Setting Modifiers - Sony XVS-G1 User Manual

Frame I/O (2-channel mode) pattern numbers
2861 to 2864
No. Parameter Adjustment
1 Rot X Rotation around Y-axis (rotation in
horizontal direction)
2 Rot Y Rotation around X-axis (rotation in
vertical direction)
3 Rot Z Rotation around Z-axis
5 Delay Timing for image selected on a
utility bus to enter the frame
Brick (3-channel mode) pattern number 3601
No. Parameter Adjustment
1-1 Side V Size X Side V horizontal scaling factor
1-2 Side V Size Y Side V vertical scaling factor
1-3 Height Height of brick
1-4 Side V Center X Side V horizontal center position
1-5 Side V Center Y Side V vertical center position
2-1 Side H Size X Side H horizontal scaling factor
2-2 Side H Size Y Side H vertical scaling factor
2-3 Height Height of brick
2-4 Side H Center X Side H horizontal center position
2-5 Side H Center Y Side H vertical center position
a) The [Height] parameter in numbers 1-3 and 2-3 are common.
b) Side V/side H image horizontal center position. At –100.00, the center is
at the left edge of the screen. At +100.00, the center is at the right edge of
the screen.
c) Side V/side H image vertical center position. At –100.00, the center is at
the bottom edge of the screen. At +100.00, the center is at the top edge of
the screen.

Setting Modifiers

You can add modifiers to modify a DME wipe pattern.
Direction
Sets the direction of travel of the DME wipe.
Notes
• The direction cannot be set for the following patterns.
- Frame I/O pattern numbers 1201, 1202, 1203, 1205,
1206, 1208, 1209, 1225
- P in P pattern number 1251
- Mosaic pattern number 1701
- Defocus pattern number 1702
• In a key DME wipe, the direction can be set for the
following patterns.
- Frame I/O pattern numbers 1204, 1207, 1221 to 1224
- Resizer Frame I/O pattern numbers 7204, 7207, 7221
to 7224
Edge
Adds a border to a DME wipe pattern.
Note
The edges cannot be set for the following patterns.
• Split pattern numbers 1011, 1012, 1013
• Mosaic pattern number 1701
• Defocus pattern number 1702
Position
You can move a DME wipe pattern to a desired position.
You can move to a specified position (upper left, upper
right, bottom left, bottom right) using Position Select.
The position can be set for the following patterns.
The target position and movement varies depending on the
pattern.
• Squeeze pattern number 1031
Resizer Squeeze pattern number 7031
As the transition progresses, the pattern center
automatically moves from the initial set position toward
a)
the center of the screen.
b)
• Squeeze pattern numbers 1032, 1033
You can set the pattern position at the start of the
c)
transition. As the transition progress resumes after the
dead band, the pattern automatically moves from the
initial position toward the center of the screen.
a) • Frame I/O pattern numbers 1201 to 1209, 1221 to 1225
P in P pattern number 1251
b)
Resizer Frame I/O pattern numbers 7201 to 7208, 7221
c)
to 7224
You can set the pattern position at the end of the first
transition.
• P in P pattern numbers 2651, 2652
You can configure each channel separately, or configure
two channels simultaneously, depending on their
relative positions.
• Brick pattern numbers 2801 to 2804, 2811 to 2814
You can set the vertical position where the brick slides
in.
• Frame I/O pattern numbers 2851 to 2854, 2861 to 2864
You can set the pattern position at the end of the first
transition for each channel.
Size
Sets the size of a DME wipe pattern.
Note
The size can be set for the following patterns.
• Frame I/O pattern numbers 1201 to 1209, 1221 to 1225,
2851 to 2854, 2861 to 2864
• P in P pattern numbers 1251, 2651, 2652
• Resizer Frame I/O pattern numbers 7201 to 7208, 7221
to 7224
Crop
Crops the top, bottom, left, right sides of a DME wipe
pattern.
116