Clip Player Content Operations - Sony XVS-G1 User Manual

For details, see "Properties display" (page 272).
Selecting a clip player output channel
Use the menu for the target clip player output channel for
operation.
When clip player output channel 1 (Clip 1) or clip player
output channel 2 (Clip 2) is selected, open the following
menu.
To recall video content:
Open the Home > Clip Player > Clip1/Clip2 > Clip >
Recall menu (14101.11).
The odd-numbered clip player output channel (Clip 1)
is shown on the upper left, and the even-numbered clip
player output channel (Clip 2) is shown on the lower
left. Content can be displayed in list view or thumbnail
view on the right.
For combined channels, the combined clip player
output channels (Clip 1/Clip 2) are shown on the left.
To play video content:
Home > Clip Player > Clip1/Clip2 > Clip > Play menu
(14101.12).
Information and operation buttons for the odd-
numbered clip player output channel (Clip 1) are
shown at the top, and information and operation
buttons for the even-numbered clip player output
channel (Clip 2) are shown at the bottom.
For combined channels, information and operation
buttons for the combined clip player output channels
(Clip 1/Clip 2) are shown.
Combining clip player output channels
Enable group mode.
This section describes combining Clip 1 and Clip 2 as an
example.
1
Open the Home > Clip Player > Clip Common >
Channel > Config menu (14103.32).
The combine status is displayed for each clip player
output channel.
2
Set the [ ] button between [Clip 1] and [Clip 2] to the
on state.
Group mode becomes enabled, Clip 1 and Clip 2
output channels are combined, and a blue frame
appears. The clip player output channel display
changes to [Clip 1/Clip 2].
To uncombine, set the [
To enable group mode using the clip player
output channel menu
Set the [Group Mode] button to the on state in the Home >
Clip Player > Clip1/Clip2 > Clip > Recall menu
(14101.11).
] button to the off state.
138
Notes
• Channels cannot be combined/uncombined in the
following cases.
- When channels are locked
- When playing video
• If group mode is enabled while content is recalled on a
clip player output channel, the following occurs.
- If content 1 of combined content is recalled on Clip 1
and no content is recalled on Clip 2, the channels are
combined and content 2 corresponding to the
combined content on Clip 1 is recalled on Clip 2.
- If content 1 of combined content is recalled on Clip 1
and other content is recalled on Clip 2, a message
appears. If you press [OK], the content recalled on
Clip 2 is released, the channels are combined and
content 2 corresponding to the combined content on
Clip 1 is recalled on Clip 2.
- In all other cases, when content is recalled on Clip 1 or
Clip 2, a message appears. If you press [OK], the
recalled content is released, the channels are
combined, and both Clip 1 and Clip 2 become black
signals.
• If group mode is disabled while combined content is
recalled on Clip 1 and Clip 2, a message appears. If you
press [OK], the channels are uncombined, content 1 of
the combined content remains recalled on Clip 1, content
2 recalled on Clip 2 is released, and Clip 2 becomes a
black signal.
Locking clip player output channels
You can lock a clip player output channel when video
content is recalled on the clip player output channel.
The following operations are inhibited on a locked clip
player output channel.
• Recalling content
• Enabling/disabling audio
The following operations are inhibited for content recalled
on a locked clip player output channel.
• Unloading content
• Deleting content
To lock Clip 1, set the [Output Lock] switch for [Clip 1] to
the on state in the following menus.
• Home > Clip Player > Clip1/Clip2 > Clip > Recall menu
(14101.11)
• Home > Clip Player > Clip1/Clip2 > Clip > Play menu
(14101.12)

Clip Player Content Operations

For details about displaying and selecting content, see
"Content Operations" (page 271).