Setting A Disk Recorder (Vdcp) - Sony XVS-G1 User Manual

3
In the [TC Source] group, select a timecode source
(reference number for determining the tape position).
LTC: Use LTC (Longitudinal Time Code).
When interpolation data is returned from a VTR,
use that interpolation data.
LTC:VITC: Normally use LTC, except when the tape
is moving at speeds at which LTC cannot be read,
use VITC.
When interpolation data is returned from a VTR,
use that interpolation data.
VITC: Use VITC (Vertical Interval Time Code).
CTL: Use CTL (Control) pulse or timer counter pulse.
Use this only for a tape on which no timecode is
recorded.
4
In the list on the right, set the VTR constants of the
item.
Press the [Setting] button for an item to set and enter a
VTR constant (00 to FF) in the numeric keypad
window.
Item Item description
VTR Constant HI-BYTE (DEVICE TYPE)
Block1 Byte1
VTR Constant LO-BYTE (DEVICE TYPE)
Block1 Byte2
VTR Constant HI-BYTE (FRAME) (PREROLL TIME)
Block1 Byte3
VTR Constant LO-BYTE (FRAME) (PREROLL TIME)
Block1 Byte4
VTR Constant EDIT DELAY (FRAME)
Block1 Byte5
VTR Constant EE DELAY (FRAME)
Block1 Byte6
VTR Constant OVER RUN (FRAME)
Block1 Byte7
VTR Constant TRAJECTORY
Block1 Byte8
VTR Constant TC READ DELAY (FRAME)
Block2 Byte1
VTR Constant START DELAY (FRAME)
Block2 Byte2
VTR Constant AFTER SYNC DELAY –
Block2 Byte3
VTR Constant AFTER SYNC DELAY +
Block2 Byte4
VTR Constant MODE1
Block2 Byte5
VTR Constant MODE2
Block2 Byte6
VTR Constant MAX PRRL SPEED
Block2 Byte7
VTR Constant QUICK PVW PRRL TIME (FRAME)
Block2 Byte8

Setting a Disk Recorder (VDCP)

1
Open the Home > Setup > External Device > Serial/
Net Port Setting > DDR VDCP menu (19105.63).
A list of ports is shown on the left and the settings
status of the selected port is shown on the right.
2
In the list on the left, select the target port to set.
3
In the [DDR Type] group, select a type of disk
recorder.
Player: Player
Recorder: Recorder
4
In the [Name Mode] group, select a file name mode.
Fixed 8 Character: 8-character file name
Variable Length: Variable-length file name (up to 23
characters)
5
In the [Frame Control Mode] group, select a frame
control mode.
For a disk recorder that does not support a timecode
with a drop frame bit, set drop frame mode or non drop
frame mode.
Drop Frame: Drop frame mode
Non Drop Frame: Non-drop frame mode
Notes
• Configurable only when the system signal format
frequency is 59.94.
• If the drop frame bit of the timecode is set, it
operates in drop frame mode.
6
In the [TC Sense] group, select a timecode sense
mode.
Zero based: Timecode sense (detection), taking the
first frame of the loaded file as 00:00:00:00.
SOM based: Sense (detection) occurs using the
timecode recorded in the loaded file.
7
Enable/disable duration detection using the [Duration
Sense] button.
On: Enable duration sense (detection).
Off: Disable duration sense (detection).
8
In the list on the right, set the video port and response
speed of the item.
Press the [Setting] button for an item to set and enter a
setting in the numeric keypad window.
336