Sony XVS-G1 User Manual page 168

Play the target device to set using the device control
block and press the [STOP TC] button at the position
to set as the stop point.
5
Set loop/recue.
Press the [LOOP] button, turning it on, to set loop. Or
press the [RECUE] button, turning it on, to set recue.
To set neither loop or recue, set the [LOOP] button and
[RECUE] button to the off state.
Note
Loop/recue are only available for disk recorders that
use the video disk communications protocol.
Setting cueup & play (menu)
1
Select a region and recall a register.
In the [Effect Timeline Recall/Store] taskbar, press the
[Recall/Store] button to display the [Recall/Store
Register] window. Select an external device region
(Device1 to Device12), press the [Recall] button, enter
a register number, and press [Enter].
For details about recalling an effect timeline register,
see "Recalling an Effect Timeline" (page 200).
2
Open the Home > External Device > Device > Cueup
& Play menu (16101.31).
Cueup & play settings information is displayed for
each device channel number (1 to 12).
3
Select the target device for operation.
4
Press the left button in the [Start TC] group and enter
a start point timecode in the numeric keypad window.
To clear the setting
Press the [Clear] button in the [Start TC] group.
5
Press the left button in the [Stop TC] group and enter
a stop point timecode in the numeric keypad window.
To clear the setting
Press the [Clear] button in the [Stop TC] group.
6
Press the left button in the [Delay] group and enter a
start delay time in the numeric keypad window.
Set a value in the range 00:00 to 59:xx ("xx" is the
number of frames per second – 1 frame).
To clear the setting
Press the [Clear] button in the [Delay] group.
7
In the [Mode] group, set loop/recue.
Loop: Set loop.
Recue: Set recue.
To set neither loop or recue, set the [Loop] button and
[Recue] button to the off state.
Note
Loop/recue are only available for disk recorders that
use the video disk communications protocol.
8
Save the register.
In the [Effect Timeline Recall/Store] taskbar, press the
[Recall/Store] button to display the [Recall/Store
Register] window. Press the [Store] button, check the
register number, and press [Enter]. You can change the
register number if you want to save in a register
different from the recalled register.
For details about saving an effect timeline register, see
"Saving an Effect Timeline" (page 201).
Executing cueup & play (utility control
block)
You can execute cueup & play using the utility control
block.
Selecting regions and recalling registers are controlled
using the menu.
For details, see "Executing cueup & play (menu)"
(page 168).
You can also select a region and recall an effect timeline
register by recalling a shotbox register in the utility control
block.
For details, see "Executing a Shotbox (Utility Control
Block)" (page 234) and "Assigning a Utility Function"
(page 318).
Operate using the following buttons.
[REWIND] button: Cueup the start point timecode.
During cueup, the [ALL STOP] button in the device
control block flashes amber and then lights green
when the start point is reached. During cueup on the
reference region device when multiple devices are
selected, the [CUE] button flashes amber and then
lights green when the start point is reached.
[RUN] button: Start playback. Playback stops at the stop
point timecode.
Executing cueup & play (menu)
1
Select a region and recall a register.
In the [Effect Timeline Recall/Store] taskbar, press the
[Recall/Store] button to display the [Recall/Store
168