Toshiba e-STUDIO2006 Service Manual page 677

05/08 Mode Element Sub element
08 Setting Process Development Toner near empty
mode
08 Setting Process Fuser Fusing correction
mode control time
immediately after
warming-up
08 Setting Process Fuser Fusing correction
mode control time
immediately after
warming-up
08 Setting Process Fuser Correction of
mode temperature rising
prevention (Latest
value)
08 Setting Process Fuser Correction of
mode temperature rising
prevention (Latest
value)
08 Setting Process Fuser
mode
08 Setting Process Fuser
mode
08 Setting Process Fuser
mode
08 Setting Process Fuser
mode
© 2013-2017 TOSHIBA TEC CORPORATION All rights reserved
Sub-
Item Subitem Code
code
5156 3 Fine adjustment
ofthreshold
fordisplaying
remainingtoner and
toner nearempty
5210 0 Temperature correction
5210 1 Maximum time of lamp
ON
5337 0 Ready
5337 1 Printing
5469 - Low power
consumption control
5497 0 Low power
consumption control:
Lamp maximum ON
time (Center)
5497 1 Low power
consumption control:
Lamp maximum ON
time (Side)
5497 2 Low power
consumption control:
Lamp maximum ON
time (Center)
Default Acceptable
Details SRAM
value value
100 50-150 M
2 0-10 M
2 0-10 M
0 0-15 M
0 0-15 M
1 0-1 M
10 1-50 M
10 1-50 M
10 1-50 M
14-2-61
Contents
Adjusts the threshold value for displaying remaining
amount of toner and toner near empty. Display threshold
value = default threshold value x setting value/100 (unit: %)
50: Setting value x 0.5
100: Setting value x 1.0
150: Setting value x 1.5
0: Disable 1: 1 min. 2: 2 min. 3: 3 min. 4: 4 min. 5: 5 min. 6:
6 min. 7: 7 min. 8: 8 min. 9: 10 min. 10: 15 min.
0: Disable 1: 1 min. 2: 2 min. 3: 3 min. 4: 4 min. 5: 5 min. 6:
6 min. 7: 7 min. 8: 8 min. 9: 10 min. 10: 15 min.
o o o o o o
0: 0 C 1: -1 C 2: -2 C 3: -3 C 4: -4 C 5: -5 C 6: -6
o o o o o
-7 C 8: -8 C 9: -9 C 10: -10 C 11: -11 C 12: -12
o o o
13 C 14: -14 C 15: -15 C
o o o o o o
0: 0 C 1: -1 C 2: -2 C 3: -3 C 4: -4 C 5: -5 C 6: -6
o o o o o
-7 C 8: -8 C 9: -9 C 10: -10 C 11: -11 C 12: -12
o o o
13 C 14: -14 C 15: -15 C
This code is used when using low power consumption
control. Note that inconsistent fusing may occur if the fuser
roller temperature is low. Use the above default value,
unless otherwise required.
0: Invalid, 1: Valid
This code is used to set a Lamp ON time on Low power
consumption control. Use the above default value, unless
otherwise required.
Setting value x 100 msec
This code is used to set a Lamp ON time on Low power
consumption control. Use the above default value, unless
otherwise required.
Setting value x 100 msec
This code is used to set a Lamp ON time on Low power
consumption control. Use the above default value, unless
otherwise required.
Setting value x 100 msec
e-STUDIO2303A/2303AM/2803AM/2309A/2809A
SELF-DIAGNOSIS CODE (03/04/05/08 CODE)
Proce 23LM/ 23HA/
23LA
dure 28LM 28HA
4 Y Y Y
4 Y Y Y
4 Y Y Y
o 14 Y Y Y
C 7:
o
C 13: -
o 14 Y Y Y
C 7:
o
C 13: -
1 Y Y Y
4 Y Y Y
4 Y Y Y
4 Y Y Y