Configuring Axes And Axes Groups - Omron NY532-1500 User Manual
Ny-series ipc machine controller
industrial panel pc / industrial box pc
Hide thumbs
Also See for NY532-1500:
- Reference manual (702 pages) ,
- Setup and user's manual (118 pages) ,
- Troubleshooting manual (778 pages)
Table of Contents
Advertisement
Configuring Axes and Axes
Groups
NY-series Industrial Panel PC / Industrial Box PC Motion Control User's Manual (W559)
This section describes the concept of axes and axes groups, the settings for axes that
are required for the MC test run function to operate on the Sysmac Studio, and the
instructions for creating and configuring axes and axes groups using the Sysmac Stu-
dio.
3-1 Axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-1-1
Introduction to Axes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-1-2
Introduction to Axis Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3-1-3
Introduction to Axis Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
3-1-4
Specifying an Axis in the User Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
3-2 Axis Setting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3-2-1
Axis Configuration Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3-2-2
Setting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
3-3 Axes Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3-3-1
Introduction to Axes Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
3-3-2
Introduction to Axes Group Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
3-3-3
Introduction to Axes Group Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
3-3-4
Specifying an Axes Group in the User Program . . . . . . . . . . . . . . . . . . . . . . 3-23
3-4 Setting Procedures for Axes Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
3-4-1
Setting Procedure for an Axes Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
3-4-2
Setting Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
3
3-1
Advertisement
Table of Contents
