Huawei NetEngine80E Configuration Manual - Reliability page 1126

HUAWEI NetEngine80E/40E Router
Configuration Guide - Reliability
3.
Issue 02 (2014-09-30)
[PE1-Tunnel1/0/1] tunnel-protocol mpls te
[PE1-Tunnel1/0/1] destination 3.3.3.3
[PE1-Tunnel1/0/1] mpls te tunnel-id 200
[PE1-Tunnel1/0/1] mpls te signal-protocol cr-static
[PE1-Tunnel1/0/1] mpls te bidirectional
[PE1-Tunnel1/0/1] mpls te commit
[PE1-Tunnel1/0/1] quit
# Configure an MPLS TE tunnel from PE2 to PE1 and PE3.
[PE2] interface tunnel1/0/0
[PE2-Tunnel1/0/0] ip address unnumbered interface loopback 0
[PE2-Tunnel1/0/0] tunnel-protocol mpls te
[PE2-Tunnel1/0/0] destination 1.1.1.1
[PE2-Tunnel1/0/0] mpls te tunnel-id 100
[PE2-Tunnel1/0/0] mpls te signal-protocol cr-static
[PE2-Tunnel1/0/0] mpls te commit
[PE2-Tunnel1/0/0] quit
[PE2] interface tunnel1/0/2
[PE2-Tunnel1/0/2] ip address unnumbered interface loopback 0
[PE2-Tunnel1/0/2] tunnel-protocol mpls te
[PE2-Tunnel1/0/2] destination 3.3.3.3
[PE2-Tunnel1/0/2] mpls te tunnel-id 300
[PE2-Tunnel1/0/2] mpls te signal-protocol cr-static
[PE2-Tunnel1/0/2] mpls te bidirectional
[PE2-Tunnel1/0/2] mpls te commit
[PE2-Tunnel1/0/2] quit
# Configure an MPLS TE tunnel from PE3 to PE1 and PE2.
[PE3] interface tunnel1/0/1
[PE3-Tunnel1/0/1] ip address unnumbered interface loopback 0
[PE3-Tunnel1/0/1] tunnel-protocol mpls te
[PE3-Tunnel1/0/1] destination 1.1.1.1
[PE3-Tunnel1/0/1] mpls te tunnel-id 200
[PE3-Tunnel1/0/1] mpls te signal-protocol cr-static
[PE3-Tunnel1/0/1] mpls te commit
[PE3-Tunnel1/0/1] quit
[PE3] interface tunnel1/0/2
[PE3-Tunnel1/0/2] ip address unnumbered interface loopback 0
[PE3-Tunnel1/0/2] tunnel-protocol mpls te
[PE3-Tunnel1/0/2] destination 2.2.2.2
[PE3-Tunnel1/0/2] mpls te tunnel-id 300
[PE3-Tunnel1/0/2] mpls te signal-protocol cr-static
[PE3-Tunnel1/0/2] mpls te commit
[PE3-Tunnel1/0/2] quit
Configure the ingress and egress for a static bidirectional co-routed LSP.
NOTE
A static bidirectional co-routed LSP on an ingress can go Up only when the LSP name is the same
as the tunnel interface name on the ingress. Note that the initial letters of the tunnel interfaces are in
upper case. Transit and egress names do not have this limit.
# Configure PE1 as the ingress for the static bidirectional co-routed LSPs from PE1 to PE2
and from PE1 to PE3.
[PE1] bidirectional static-cr-lsp ingress Tunnel/0/0
[PE1-bi-static-ingress-Tunnel1/0/0] forward nexthop 10.1.2.2 out-label 20
bandwidth ct0 10000
[PE1-bi-static-ingress-Tunnel1/0/0] backward in-label 30
[PE1] bidirectional static-cr-lsp ingress Tunnel/0/1
[PE1-bi-static-ingress-Tunnel1/0/1] forward nexthop 10.1.3.2 out-label 40
bandwidth ct0 10000
[PE1-bi-static-ingress-Tunnel1/0/1] backward in-label 50
[PE1-bi-static-ingress-Tunnel1/0/1] quit
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10 Bit-Error-Triggered Protection Switching Configuration
1109