4Wd Position Indicator Operation Check; 4Wd Control System Operation Inspection; Visual Inspection - Suzuki 2006 SX4 Service Manual

3B-10 Differential:
Step 5. Trouble symptom confirmation
Check trouble symptoms based on information obtained
in "Step 1. Customer complaint analysis: " and "Step 2.
DTC check, record and clearance: ".
Also, reconfirm DTC according to "DTC Confirmation
Procedure" described in each DTC flow.
Step 6 and 7. Rechecking and record of DTC
Refer to "DTC Check" for checking procedure.
Step 8. 4WD control symptom diagnosis
Check the parts of the system suspected as a possible
cause referring to "4WD Control Symptom Diagnosis".
Step 9. Troubleshooting for DTC
Based on the DTC indicated in Step 6 / 7 and referring to
"applicable DTC flow", locate the cause of the trouble,
namely in a sensor, switch, wire harness, connector,
coupling assembly, 4WD control module or other part
and repair or replace faulty parts.
Step 10. Check for intermittent problem
Check parts where an intermittent trouble is easy to
occur (e.g. wire harness, connector, etc.), referring to
"Intermittent and Poor Connection Inspection in Section
00" and related circuit of DTC recorded in Step 2.
Step 11. Final confirmation test
Confirm that the problem symptom has gone and the
vehicle is free from any abnormal conditions. If what has
been repaired is related to the malfunction DTC, clear
the DTC once and check to ensure that no malfunction
DTC is indicated.

4WD Position Indicator Operation Check

1) Turn ignition switch to OFF position.
2) Check that 4WD position indicators turn on for about
2 seconds and then turns off.
If any faulty condition is found, proceed to "4WD
Position Indicator Does Not Come ON at Ignition
Switch ON but Engine Stops" or "4WD Position
Indicator Remains ON Steady at Ignition Switch ON".

Visual Inspection

Check the following parts and systems visually.
Inspection Item
• Rear differential oil ---- level, leakage
• Transfer gear oil ---- level, leakage
• Manual transmission oil ---- level, leakage
• Rear differential mounting(s) ---- wear and looseness
• Fuses ---- burning
• Battery ---- fluid level, corrosion of terminal
• Connectors of electric wire harness ---- disconnection,
friction
• Other parts that can be checked visually

4WD Control System Operation Inspection

NOTE
• It automatically changes into "4WD-auto"
position, when the vehicle speed becomes
specified speed or more at "4WD-lock"
position. It is "4WD-auto" position until
switch will be selected to "4WD-lock"
position at next time.
• When ABS operates while changed of each
position, it is discontinued of change. End
of the ABS operation, and then returned to
the position of before.
1) Inspect switch operation from "4WD-auto" to "2WD"
as follows.
a) Start engine.
b) Push 2WD/4WD switch to "2WD" position.
c) Check that 4WD AUTO indicator and 4WD
2) Inspect switch operation from "2WD" to "4WD-auto"
as follows.
a) Start engine.
b) Push 2WD/4WD switch to "AUTO" position.
c) Check that 4WD AUTO indicator comes ON
3) Inspect switch operation from "4WD-auto" to "4WD-
lock" as follows.
a) Start engine.
b) Push 2WD/4WD switch to "LOCK" position, and
c) Check that 4WD AUTO indicator not come ON
S6RW0C3204002
4) Inspect switch operation from "4WD-lock" to "4WD-
auto" as follows.
a) Start engine.
b) Push 2WD/4WD switch to "AUTO" position.
c) Check that 4WD AUTO indicator comes ON
"Rear Differential Oil Change"
"Transfer Oil Change in Section 3C"
"Manual Transaxle Oil Change in Section 5B"
"Battery Inspection in Section 1J"
"Intermittent and Poor Connection Inspection in Section
00"
LOCK indicator not come ON.
steady and 4WD LOCK indicator not come ON.
keep it for 3 seconds or more.
and 4WD LOCK indicator comes ON steady.
steady and 4WD LOCK indicator not come ON.
Referring
S6RW0C3204003
S6RW0C3204004