Siemens SINAMICS G150 Manual page 1016

2 Parameters
2.3 Parameters for data sets
p0625[0...n]
p0626[0...n]
p0627[0...n]
p0628[0...n]
p0629[0...n]
r0630[0...n]
r0631[0...n]
r0632[0...n]
r0633[0...n]
p0634[0...n]
p0635[0...n]
p0636[0...n]
p0637[0...n]
p0643[0...n]
p0650[0...n]
p0651[0...n]
p0652[0...n]
p0653[0...n]
p0655[0...n]
p0656[0...n]
p0657[0...n]
p0658[0...n]
p0659[0...n]
p0660[0...n]
p0826[0...n]
p0827[0...n]
p1231[0...n]
p1232[0...n]
p1233[0...n]
p1234[0...n]
p1236[0...n]
p1237[0...n]
p1909[0...n]
p1980[0...n]
p1982[0...n]
p1991[0...n]
p1999[0...n]
p4610[0...n]
p4611[0...n]
p4612[0...n]
p4613[0...n]
r5398[0...n]
r5399[0...n]
1016
Motor ambient temperature during commissioning / Mot T_ambient
Motor overtemperature, stator core / Mot T_over core
Motor overtemperature, stator winding / Mot T_over stator
Motor overtemperature rotor winding / Mot T_over rotor
Stator resistance reference / R_stator ref
Mot_temp_mod ambient temperature / Mod T_ambient
Mot_temp_mod stator iron temperature / Mod T_stator
Mot_temp_mod stator winding temperature / Mod T_winding
Mot_temp_mod rotor temperature / Mod rotor temp
Q flux flux constant unsaturated / PSIQ KPSI UNSAT
Q flux quadrature axis current constant unsaturated / PSIQ KIQ UNSAT
Q flux direct axis current constant unsaturated / PSIQ KID UNSAT
Q flux flux gradient saturated / PSIQ Grad SAT
Overvoltage protection for synchronous motors / Overvolt_protect
Actual motor operating hours / Mot t_oper act
Motor operating hours maintenance interval / Mot t_op maint
Motor stator resistance scaling / Mot R_stator scal
Motor stator leakage inductance scaling / Mot L_S_leak scal
Motor magnetizing inductance d axis saturated scaling / Mot L_m d sat scal
Motor magnetizing inductance q axis saturated scaling / Mot L_m q sat scal
Motor damping inductance d axis scaling / Mot L_damp d scal
Motor damping inductance q axis scaling / Mot L_damp q scal
Motor damping resistance d axis scaling / Mot R_damp d scal
Motor damping resistance q axis scaling / Mot R_damp q scal
Motor changeover motor number / Mot_chng mot No.
Motor changeover status word bit number / Mot_chg ZSW bitNo.
Armature short-circuit / DC braking configuration / ASC/DCBRK config
DC braking braking current / DCBRK I_brake
DC braking time / DCBRK time
Speed at the start of DC braking / DCBRK n_start
Ext. armature short-cct. contactor feedback signal monit. time / ASC ext t_monit
External armature short-circuit delay time when opening / ASC ext t_wait
Motor data identification control word / MotID STW
PolID technique / PolID technique
PolID selection / PolID selection
Motor changeover angular commutation correction / Ang_com corr
Ang. commutation offset calibr. and PollD scaling / Com_ang_offs scal
Motor temperature sensor 1 sensor type MDS / Temp sens1 typ MDS
Motor temperature sensor 2 sensor type MDS / Temp sens2 typ MDS
Motor temperature sensor 3 sensor type MDS / Temp sens3 typ MDS
Motor temperature sensor 4 sensor type MDS / Temp sens4 typ MDS
Mot_temp_mod 3 alarm threshold image p5390 / A thr image p5390
Mot_temp_mod 3 fault threshold image p5391 / F thr image p5391
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A