8-114 Tray 3 Prefeed Sensor On Jam RAP
The Tray 3 Prefeed Sensor did not detect paper within the specified time after the prefeed
started.
Initial Actions
•
Ensure that the No Paper Sensor is properly installed in the Paper Tray Feed Head.
•
Refer to BSD 7.7, BSD 8.3, and BSD 8.10 for the following procedure.
•
Check for any obstructions in the paper path.
•
Pull out Paper Tray 3
•
Open the Lower Left Door
(PL
2.8).
•
Open the Tray 3 Feeder
(PL
2.4).
Procedure
Cheat the L/H Cover Interlock Switch. Enter dC330 008-114 Tray 3 Pre feed Sensor and
press Start. Block the Tray 3 Prefeed Sensor with a sheet of paper. The
from H to L.
Y
N
The display indicates a constant H.
Y
N
Go to
Flag 1
on BSD 8.3 and check the harness for a short circuit. If the harness is
good, replace the Tray 3 Prefeed Sensor
Connect the meter from P/J415A-11 on the IOT Drive PWB to machine frame. Block the
Tray 3 Prefeed Sensor with a sheet of paper. The voltage at P/J415A-11 goes from +5
VDC when the sensor is not blocked, to less than +1.0 VDC when the sensor is
blocked.
Y
N
There is +5 VDC between P/J803B-5 and P/J803B-3 on the Tray PWB.
Y
N
Go to
Flag 2
on BSD 8.3 and check the harness for a short circuit. If the har-
ness is good, replace the Tray PWB
Go to
Flag 1
and
Flag 2
on BSD 8.3 and check the harness for an open circuit. If the
harness is OK, replace the Tray 3 Prefeed Sensor
replace the Tray PWB
(PL
9.3).
Replace the Tray PWB
(PL
9.3).
Enter dC330 008-018 Tray 3 Feed/Lift Motor (Feed). Press Start and Stop several times.
The Tray 3 Feed/Lift Motor energizes and deenergizes.
Y
N
Go to the
7-283 Tray 3 Lift Motor Failure RAP
Enter dC330 008-016 Tray 3 Nudger Roll Solenoid. Press Start and Stop several times.
The Tray 3 Nudger Solenoid energizes.
Y
N
Press the Stop button. There is +24 VDC at P/J803B-1 on the Tray PWB.
Y
N
Replace the Tray PWB
(PL
9.3).
A
B
Status Indicator RAPs
8-114 Tray 3 Prefeed Sensor On Jam RAP
display
changes
(PL
2.5).
(PL
9.3).
(PL
2.5). If the problem continues,
manuals4you.com
manuals4you.com
A
B
There is +24 VDC at P/J803B-2 on the Tray PWB.
Y
N
Go to
Flag 7
on BSD 7.7 and check the harness for an open circuit. If the harness is
good, replace the Tray 3 Nudger Solenoid
Press Start. The voltage at P/J803B-2 goes to approximately 0 VDC.
Y
N
Press Start. There is +5 VDC at P/J801B-10 of the Tray PWB.
Y
N
Go to
Flag 8
on BSD 7.7 and check the harness for an open or short circuit. If
the harness is good, replace the IOT Drive PWB
Replace the Tray PWB
(PL
Replace the Tray 3 Nudger Solenoid
Enter dC330 008-019 Tray 3 Take Away Feed Clutch. Press Start and Stop several times.
The Tray 3 Takeaway Feed Clutch energizes.
Y
N
Press the Stop button. There is +24 VDC at P/J802B-12 on the Tray PWB.
Y
N
Replace the Tray PWB
(PL
There is +24 VDC at P/J802B-11 on the Tray PWB.
Y
N
Go to
Flag 5
on BSD 8.3 and check the harness for an open circuit. If the harness is
good, replace the Tray 3 Takeaway Feed Clutch
Press the Start button. The voltage at P/J802B-11 goes to approximately 0 VDC.
Y
N
There is +5 VDC at P/J801B-7 on the Tray PWB.
Y
N
Go to
Flag 6
on BSD 8.3 and check the harness for an open circuit. If the har-
ness is good, replace the IOT Drive PWB.
Replace the Tray PWB
(PL
Replace the Tray 3 Takeaway Feed Clutch
Check/replace the Tray 3 Feeder Assembly
broken, binding, or slipping.
1/05
2-86
(PL
2.5).
(PL
9.2).
9.3).
(PL
2.5).
9.3).
(PL
2.7A).
9.3).
(PL
2.7A).
(PL
2.4). Replace any components that are worn,
DocuColor 12/DCCS50
Reissue