10-133 Duplex Out Sensor On Jam Rap - Xerox DocuColor 12/DCCS50 Service Manual

10-133 Duplex Out Sensor On Jam RAP

The Duplex Out Sensor did not actuate within the specified time after the start of Reverse
Feed.
Initial Actions
Refer to BSD 10.8, 10.9, and 10.12 for the following procedure.
Check for the following:
• Proper Nip Drive force at Drive Rolls (Baffle latches properly).
• Obstructions in the paper path.
• Contamination on the Duplex Path Roll
• Ensure that connectors P/J412A, P/J417A, and
Drive PWB and there are no obvious crimped or broken wires.
Procedure
Enter dC330 010-133 Duplex Out Sensor. Ensure the Drawer is closed. Press Start. The
display indicates L.
Y N
Connect the meter from P/J420-A5 on the IOT Drive PWB to GND. The
cates less than +1.0 VDC.
Y N
There is +5 VDC between P/J420-A6 and P/J420-A4 on the IOT Drive PWB.
Y N
Go to Flag 6 on BSD 10.10. Check the harness for a short circuit. If the harness
is good, replace the IOT Drive PWB
Check the actuator for the Duplex Out Sensor. If it is good, go to
on BSD 10.10 and check the harness for an open circuit. If the harness is good,
replace the Duplex Out Sensor
Drive PWB (PL 9.2).
Replace the IOT Drive PWB (PL 9.2).
NOTE: To block the Duplex Out Sensor, open the Drawer then open Jam Clearance Lever 3
on the bottom of the Drawer. Place a sheet of paper on the baffle, close the baffle and Drawer.
Block the Duplex Out Sensor with a sheet of paper. The display indicates H.
Y N
Go to Flag 5 on BSD 10.10. Check the harness for a short circuit. If the harness is good,
replace the Duplex Out Sensor (PL 2.21).
Enter dC330 010-025 Inverter Roll Solenoid Nip. Press Start. The Release Solenoid ener-
gizes.
Y N
Press Stop. +24 VDC is measured between P/J412A-14 and GND.
Y N
+24 VDC is measured between P/J412A-13 and GND.
Y N
Replace the IOT Drive PWB
A B C
Status Indicator RAPs
10-133 Duplex Out Sensor On Jam RAP
(PL 2.21).
P/J420 are seated correctly on the IOT
meter
(PL 9.2).
Flag 5 and
(PL 2.21). If the problem continues, replace the IOT
(PL 9.2).
A B C
Go to Flag 4 on BSD 10.8 and check the harness for an open circuit. If the harness is
good, replace the Release Solenoid
Press Start. The voltage at P/J412A-14 momentarily goes to approximately +12 to
+15 VDC then returns to +24 VDC.
Y N
Replace the IOT Drive PWB
Replace the Release Solenoid
Enter dC330 010-026 Inverter Roll Solenoid Release. Press Start. The Release Solenoid
deenergizes.
Y N
Press Stop. +24 VDC is measured between P/J412A-12 and GND.
Y N
Go to Flag 5 on BSD 10.8 and check the harness for an open circuit. If the harness is
good, replace the Release Solenoid
Press Start. The voltage at P/J412A-12 momentarily goes to approximately +12 to
+15 VDC then returns to +24 VDC.
Y N
indi-
Replace the IOT Drive PWB
Replace the Release Solenoid
Enter dC330 010-020 Inverter Motor Forward. Press Start and Stop several times. The
Inverter Motor energizes and deenergizes.
Y N
Press Stop. +24 VDC is measured between P/J417A-13, 14, 17, 18 on the IOT Drive
Flag 6
PWB and GND.
Y N
+24 VDC is measured between P/J417A-15 on the IOT Drive PWB and GND.
Y N
Replace the IOT Drive PWB
Go to Flag 4 and Flag 5
harness and connectors are OK, replace the Inverter Motor
Press Start. The voltage at P/J417A-13, 14, 17, 18 on the IOT Drive PWB goes to
approximately +18 VDC.
Y N
Replace the IOT Drive PWB
Replace the Inverter Motor
Enter dC330 010-021 Inverter Motor Reverse. Press Start and Stop several times. The
Inverter Motor energizes and deenergizes.
Y N
Replace the IOT Drive PWB
Check for obvious damage, missing and/or broken Drive Motor gear assemblies and drive
belts that would cause the paper to be slow to actuate the Duplex Out Sensor.
1/05
2-150
manuals4you.com manuals4you.com
(PL 2.24).
(PL 9.2).
(PL 2.24).
(PL 2.24).
(PL 9.2).
(PL 2.24).
(PL 9.2).
on BSD 10.9 and check the harness and connectors. If the
(PL
(PL 9.2).
(PL 2.24).
(PL 9.2).
DocuColor 12/DCCS50
2.24).
Reissue