Malfunction Indicator Lamp (Mil) Check; Diagnosis Connector); Power" Lamp Operation Check - Suzuki GRAND VITARA Owner's Manual

5A-20 Automatic Transmission/Transaxle:
NOTE
The form is a standard sample. It should be modified according to conditions characteristic of each
market.
Step 2. DTC / Freeze Frame Data Check, Record and
Clearance
First, referring to "DTC Check: ", check DTC (including
pending DTC). If DTC exists, print or write down DTC
and freeze frame data and then clear them by referring
to "DTC Clearance: ". DTC indicates malfunction in the
system but it is not possible to know from it whether the
malfunction is occurring now or it occurred in the past
and normal condition has been restored. In order to
know that, check symptom in question according to Step
5 and then recheck DTC according to Step 6.
Diagnosing a trouble based on the DTC in this step only
or failure to clear the DTC in this step may result in an
faulty diagnosis, trouble diagnosis of a normal circuit or
difficulty in troubleshooting which is otherwise
unnecessary.
Step 3 and Step 4. Visual Inspection
As a preliminary step, be sure to perform visual check of
the items that support proper function of the A/T and
engine referring to "Visual Inspection: ".
Step 5. Trouble Symptom Confirmation
Check trouble symptoms based on information obtained
in Step 1 "Customer Complaint Analysis" and Step 2
"DTC/Freeze Frame Data Check, Record and
Clearance".
Also, recheck DTC according to "DTC Confirmation
Procedure" described in each DTC flow.
Step 6 and Step 7. Recheck and Record of DTC /
Freeze Frame Data
Refer to "DTC Check: " for checking procedure.
Step 8. A/T Basic Check and A/T Trouble Diagnosis
Perform A/T basic check according to "A/T Basic Check:
" first. When the end of the flow has been reached,
check the parts of the system suspected as a possible
cause referring to "A/T Symptom Diagnosis: " and based
on symptoms appearing on the vehicle (symptoms
obtained through steps of customer complaint analysis,
trouble symptom confirmation and/or A/T basic check)
and repair or replace faulty parts, if any.
Step 9. Troubleshooting for DTC
Based on the DTC indicated in Step 6 and 7 and
referring to applicable DTC flow, locate the cause of the
trouble, namely in a sensor, switch, wire harness,
connector, actuator, TCM or other part and repair or
replace faulty parts.
Step 10. Check for Intermittent Problem
Check parts where an intermittent trouble is easy to
occur (e.g., wire harness, connector, etc.), referring to
"Intermittent and Poor Connection Inspection: in Section
00" and related circuit of DTC recorded in Step 2.
Step 11. Final Confirmation Test
Confirm that the problem symptom has gone and the A/T
is free from any abnormal conditions.
If what has been repaired is related to the malfunction
DTC, clear the DTC once, set conditions under which
DTC was detected and A/T and/or vehicle was repaired
and confirm that no DTC is indicated.

Malfunction Indicator Lamp (MIL) Check

Refer to "Malfunction Indicator Lamp (MIL) Check: in
Section 1A".
Transmission Warning Light Operation Check
(Vehicle is Equipped with Engine Diagnosis
Connector)
1) Turn ignition switch ON.
2) Check that transmission warning light lights for about
2 – 4 sec. and then goes OFF. If anything faulty is
found, advance "Transmission Warning Light Circuit
Check – Light Does Not Come "ON" at Ignition
Switch ON (Vehicle is equipped with engine
diagnosis connector): " or "Transmission Warning
Light Circuit Check – Light Remains "ON" at Ignition
Switch ON (Vehicle is equipped with engine

diagnosis connector): ".

"POWER" Lamp Operation Check

1) Turn ignition switch ON.
2) Check that "POWER" lamp lights for about 2 – 4 sec.
and then goes OFF.
If anything faulty is found, advance to ""POWER"
Light Circuit Check – Light Does Not Come "ON" at
Ignition Switch ON: ".
S5JB0A5104002
S5JB0A5104003
S5JB0A5104004