Precautions For Dtc Troubleshooting; Precautions Of Ecm Circuit Inspection; Precautions Of Electric Throttle Body System Calibration; General Description - Suzuki GRAND VITARA Owner's Manual

Precautions For DTC Troubleshooting

• Before performed trouble shooting, be sure to read
the "Precautions of ECM Circuit Inspection: ".
• When measuring circuit voltage, resistance and/or
pulse signal at ECM connector, connect the special
tool to ECM and/or the ECM connectors referring to
"Inspection of ECM and Its Circuits: ".
• Upon completion of inspection and repair work,
perform "DTC Confirmation Procedure" and confirm
that the trouble has been corrected.

Precautions of ECM Circuit Inspection

• ECM connectors are waterproofed. Each terminal of
the ECM connectors is sealed up with the grommet.
Therefore, when measuring circuit voltage, resistance
and/or pulse signal at ECM connector, do not insert
the tester's probe into the sealed terminal at the
harness side. When measuring circuit voltage,
resistance and/or pulse signal at ECM connector,
connect the special tool to the ECM connectors. And,
insert the tester's probe into the special tool's
connectors at the harness side, and then measure
voltage, resistance and/or pulse signal. Or, ECM and
its circuits may be damaged by water.

Statement on Cleanliness and Care

An automobile engine is a combination of many
machined, honed, polished and lapped surfaces with
tolerances that are measured in the thousands of an
millimeter (ten thousands of an inch).
Accordingly, when any internal engine parts are
serviced, care and cleanliness are important.
It should be understood that proper cleaning and
protection of machined surfaces and friction areas is part
of the repair procedure. This is considered standard
shop practice even if not specifically stated.
• A liberal coating of engine oil should be applied to
friction areas during assembly to protect and lubricate
the surfaces on initial operation.
• Whenever valve train components, pistons, piston
rings, connecting rods, rod bearings, and crankshaft
journal bearings are removed for service, they should
be retained in order.
At the time of installation, they should be installed in
the same locations and with the same mating
surfaces as when removed.
• Battery cables should be disconnected before any
major work is performed on the engine.
Failure to disconnect cables may result in damage to
wire harness or other electrical parts.
• The four cylinders of the engine are identified by
numbers; No.1 (1), No.2 (2), No.3 (3) and No.4 (4)
counted from crankshaft pulley side to flywheel side.
Engine General Information and Diagnosis:
• Wire colors of the special tool's connectors are
S5JB0A1100005 different from the ones of the ECM connectors.
However, the circuit arrangement of the special tool's
connectors is same as the one of the ECM
connectors. Therefore, measure circuit voltage and
resistance by identifying the terminal location subject
to the measurement.
Precautions of Electric Throttle Body System
Calibration
After performing one of works described below, it is
necessary to re-register the completely closed throttle
valve reference position stored in memory of ECM. (For
S5JB0A1100003
detailed information, refer to "Description of Electric
Throttle Body System Calibration: ".) For the procedure
to register such data in ECM, refer to "Electric Throttle
Body System Calibration: in Section 1C".
• To shut off backup power of ECM for such purposes of
battery replacement or "DOME" fuse removal
• To erase DTCs P0122, P0123, P0222, P0223, P2101,
P2102, P2103, P2111, P2119 and/or P2135
• To replace ECM
• To replace throttle body and/or accelerator pedal
position (APP) sensor assembly

General Description

S5JB0A1101001
[A]
4
3
2
[B]
[A]: J20 engine
[B]: M16 engine
1A-2
S5JB0A1100004
1
4
3
2
1
I5JB0A110001-02