Add Parameters To The Parameter List Displayed In Stop/Running State - INVT Goodrive350 Series Operation Manual

Goodrive350 series high-performance multifunction VFD
edit operation, it will return to the previous menu (parameter list remain unchanged).
Note: For the parameter objects in the list header, shift-up operation will be invalid, and the
same principle can be applied to the parameter objects in the list footer; after deleting a
certain parameter, the parameter objects under it will be shifted up automatically.
The monitoring items displayed in the parameter list of running state can be added as needed
(through the menu of the function code in state check group), and the list can also be edited such as
"shift up", "shift down" and "delete from the list". The edit function is shown in the interface below.
16:02:35
Forward Local Ready
Parameter displayed in stop state
Parameter displayed in running state
Return Homepage
The parameter list of common parameter setup can be added, deleted or adjusted as needed,
including delete, shift-up and shift-down; the addition function can be set in a certain function code of
a function group. The edit function is shown in the figure below.
16:02:35 Forward Local Ready
Common parameter
setup
Parameter setup
State monitoring/fault
record
Motor parameter
autotuning
Parameter backup/restore
to default value
System setting
Return Homepage

5.4.3 Add parameters to the parameter list displayed in stop/running state

In the fourth-level menu of "State monitoring", the parameters in the list can be added to the
"parameter displayed in stop state" list or "parameter displayed in running state" list as shown below.
16:02:35 Forward
Local Ready
P17.00：Setting frequency
P17.01：Output frequency
P17.02：Ramps reference frequency
P17.03：Output voltage
P17.04：Output current
P17.05：Motor speed
Return Add
16:02:35 16:02:35 16:02:35 16:02:35
Forward Forward Forward Forward Local Local Local Local Ready Ready Ready Ready
P17.00: 设定频率 P17.00: 设定频率 P17.00: 设定频率
P17.00：Setting frequency
P17.01：Output frequency P17.01：输出频率 P17.01：输出频率 P17.01：输出频率
P17.02：Ramps reference frequency P17.02：斜坡给定频率 P17.02：斜坡给定频率 P17.02：斜坡给定频率
P17.03：输出电压 P17.03：输出电压 P17.03：Output voltage P17.03：输出电压
P17.04：输出电流 P17.04：Output current P17.04：输出电流 P17.04：输出电流
P17.05：电机转速 P17.05：电机转速 P17.05：电机转速 P17.05：Motor speed
返回 返回 返回 添加 添加 添加
Return Add
Press key to enter parameter addition interface, select the operation needed, and press
16:02:35
01: GD350
P17.01：Output frequency
P17.00：Set frequency
P17.11：DC bus voltage
P17.03：Output voltage
P17.04：Output current
P17.05：Motor speed
Select Return
Figure 5.11 List edit diagram 2
01: GD350 16:02:35
P00.10：Keypad setting frequency
P00.00：Speed control mode
P00.11：Acceleration time 1
P00.12：Deceleration time 1
P00.01：Running command channel
P00.13：Running direction selection
Return
Select
Figure 5.12 List edit diagram 3
16:02:35
01: GD350
Add to the parameter list displayed in stop state
Add to the parameter list displayed in running state
Return
Select
16:02:35 16:02:35 16:02:35 16:02:35
01: GD350 01：GD350 01：GD350
01：GD350
添加到停机状态显示参数 添加到停机状态显示参数 添加到停机状态显示参数
Add to the parameter list displayed in stop state
添加到运行状态显示参数 添加到运行状态显示参数 添加到运行状态显示参数
Add to the parameter list displayed in running state
返回 返回 返回
选择 选择 选择 Return
Select
Figure 5.13 Add parameter diagram 1
Forward Local Ready 01: GD350
Edit
Confirm
Forward Local Ready 01: GD350
Edit
Select
Forward
Local Ready 01: GD350
Homepage
Confirm
Forward Local Ready 01: GD350 01：GD350 01：GD350
01：GD350
主页 主页 主页
Homepage 确定 确定 确定
Confirm
-42-
Basic operation instructions
16:02:35
Forward Local Ready 01: GD350
Shift up
Shift down
Delete from the list
Return Homepage
16:02:35 Forward Local Ready 01: GD350
Shift up
Shift down
Delete from the list
Return Homepage
16:02:35 Forward
Local Ready
Ensure to add to the parameter list
displayed in stop state?
Return Homepage
16:02:35 16:02:35 16:02:35 16:02:35
Forward 01：GD350 01：GD350 01: GD350
Local Ready 01：GD350
Ensure to add to the parameter list
确认添加到运行状态显示参数？ 确认添加到运行状态显示参数？ 确认添加到运行状态显示参数？
displayed in running state?
返回 返回 返回 主页 主页 主页
Return Homepage
Select
Select
01: GD350
Confirm
确定 确定 确定
Confirm