Mitsubishi Electric MELSEC Q Series Programming Manual page 106

3 POSITIONING DEDICATED SIGNALS
(3) Manual pulse generator axis No. setting registers (D714 to D719)
(a) These registers stores the axis No. controlled with the manual pulse
generator.
b15 b14 b13 b12 b11 b10
D714
Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
P1
D715
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
D716 Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
P2
D717
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
D718 Axis 16 Axis 15 Axis 14 Axis 13 Axis 12 Axis 11 Axis 10 Axis 9 Axis 8 Axis 7 Axis 6 Axis 5 Axis 4 Axis 3 Axis 2 Axis 1
P3
D719
Axis 32 Axis 31 Axis 30 Axis 29 Axis 28 Axis 27 Axis 26 Axis 25 Axis 24 Axis 23 Axis 22 Axis 21 Axis 20 Axis 19 Axis 18 Axis 17
(b) Refer to Section 6.22 for details of the manual pulse generator operation.
(4) Manual pulse generator 1-pulse input magnification setting
registers (D720 to D751) ..................................... Command device
(a) These register set the magnification (1 to 10000) per pulse of number of the
input pulses from manual pulse generator at the pulse generator operation.
1-pulse input
magnification Axis No.
setting register
D720 Axis 1
D721 Axis 2
D722 Axis 3
D723 Axis 4
D724 Axis 5
D725 Axis 6
D726 Axis 7
D727 Axis 8
D728 Axis 9
D729 Axis 10
D730 Axis 11
D731 Axis 12
D732 Axis 13
D733 Axis 14
D734 Axis 15
D735 Axis 16
(b) Refer to Section 6.22 for details of the manual pulse generator operation.
........................ Command device
b9 b8
(Note-1): Make the axis No. controlled with the manual pulse generator
setting with 1/0.
1 : Specified axis
0 : Unspecified axis
(Note-2): The following range is valid.
Q172DSCPU : Axis No.1 to 16
Q172DCPU(-S1) : Axis No.1 to 8
1-pulse input
Setting range magnification
setting register
1 to 10000
3 - 57
b7 b6 b5 b4 b3 b2
Axis No.
D736 Axis 17
D737 Axis 18
D738 Axis 19
D739 Axis 20
D740 Axis 21
D741 Axis 22
D742 Axis 23
D743 Axis 24
D744 Axis 25
D745 Axis 26
D746 Axis 27
D747 Axis 28
D748 Axis 29
D749 Axis 30
D750 Axis 31
D751 Axis 32
(Note): The following range is valid.
• Q172DSCPU
• Q172DCPU(-S1) : Axis No. 1 to 8
b1 b0
Setting range
1 to 10000
: Axis No. 1 to 16