Siemens SINAMICS G130 Operating Instructions Manual page 592

Appendix
A.2 Parameter macros
Parameters
p1240 Vdc controller configuration
p1254 Vdc controller automatic ON level
detection
p1280 Vdc controller configuration (V/f)
p1300 Open-loop/closed-loop control
operating mode
p1911 Number of phases to be identified
p2051[0] CI: PROFIBUS PZD send word
p2051[1] CI: PROFIBUS PZD send word
p2051[2] CI: PROFIBUS PZD send word
p2051[3] CI: PROFIBUS PZD send word
p2051[4] CI: PROFIBUS PZD send word
p2051[5] CI: PROFIBUS PZD send word
p2080[0] BI: PROFIBUS send status word 1
p2080[1] BI: PROFIBUS send status word 1
p2080[2] BI: PROFIBUS send status word 1
p2080[3] BI: PROFIBUS send status word 1
p2080[4] BI: PROFIBUS send status word 1
p2080[5] BI: PROFIBUS send status word 1
p2080[6] BI: PROFIBUS send status word 1
p2080[7] BI: PROFIBUS send status word 1
p2080[8] BI: PROFIBUS send status word 1
p2080[9] BI: PROFIBUS send status word 1
p2080[10] BI: PROFIBUS send status word 1
p2080[11] BI: PROFIBUS send status word 1
p2080[12] BI: PROFIBUS send status word 1
p2080[13] BI: PROFIBUS send status word 1
p2080[14] BI: PROFIBUS send status word 1
p2080[15] BI: PROFIBUS send status word 1
p2088 PROFIBUS Invert status word
p2128[14] Select fault/alarm code for trigger
p2128[15] Select fault/alarm code for trigger
p2153 Time constant revolutions actual
value filter
p4053[0] TM31 analog inputs, smoothing
time constant
p4056[0] Type of analog inputs
p4056[1] Type of analog inputs
p4076[0] Type of analog outputs
592
Sink
Description DO Parameters
Vector 1
Vector 1
Vector 1
Vector 20
Vector 1
Vector r2089[0]
Vector r0063[0]
Vector r0068[0]
Vector r0080[0]
Vector r0082[0]
Vector r2131
Vector r0899.0
Vector r0899.1
Vector r0899.2
Vector r2139.3
Vector r0899.4
Vector r0899.5
Vector r0899.6
Vector r2139.7
Vector r2197.7
Vector r0899.9
Vector r2199.1
Vector r1407.7
Vector 0
Vector r2129.14
Vector r2197.3
Vector r2129.15
Vector B800h
Vector 7910
Vector 5000
Vector 20
TM31 0
TM31 0
TM31 0
TM31 1
Source
Description
Vdc-max controller enabled
Automatic detection enabled
Vdc-max controller enabled
Encoderless speed control
1 phase
ZSW1
n-act unsmoothed
I-act unsmoothed
M-act unsmoothed
P-act unsmoothed
FAULT
Ready for switching on
Ready for operation
Operation
Fault
No OFF2
No OFF3
Switching on inhibited
Alarm active
No setpoint/actual value deviation Vector
Control request
Comparison value reached
M/I/P limiting not active
No alarm for motor overtempera-
ture
Clockwise
No Therm. alarm Power unit
overload
A7910: Alarm, motor overtemper-
ature
A5000: Therm. alarm Power unit
overload
20 ms
0 ms
Voltage 0...10 V
Voltage 0...10 V
Voltage 0...10 V
Operating Instructions, 07/2016, A5E00331449A
DO
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
Vector
TM31
TM31
TM31
TM31
Inverter chassis units