Honda NC700 2012 Service Manual page 16

dummyhead dummyhead
NC700XD/SD
Transmission Gear I.D.
Gear bushing
O.D.
Gear-to-bushing
clearance
Gear bushing I.D.
Inner mainshaft
O.D.
Outer mainshaft
O.D.
Countershaft O.D.
Bushing-to-shaft
clearance
Shift fork, Fork I.D.
fork shaft
Claw thickness
Shift fork shaft O.D.
CRANKSHAFT/PISTON/CYLINDER SPECIFICATIONS
Crankshaft Connecting rod side clearance
Runout
Main journal bearing oil clearance
Cylinder I.D.
Out-of-round
Taper
Warpage
Piston, piston Piston O.D. at 13 mm (0.5 in) from
rings bottom
Piston pin bore I.D.
Piston pin O.D.
Piston-to-piston pin clearance
Piston ring end
gap
Piston ring-to-ring
groove clearance
Cylinder-to-piston clearance
Connecting rod small end I.D.
Crankpin bearing oil clearance
ITEM
M5
M6
C1
C2
C3, C4
M5
M6
C1
C2
C3, C4
M5
M6
C1
C2
C3, C4
M5
M6
C1
C2
At M5 bushing
At M6 bushing
At C1 bushing
At C2 bushing
M5
M6
C1
C2
ITEM
Right side
Left side
Top
Second
Oil (side rail)
Top
Second
STANDARD
33.000 – 33.025 (1.2992 – 1.3002)
43.000 – 43.025 (1.6929 – 1.6939)
31.010 – 31.035 (1.2209 – 1.2218)
25.000 – 25.021 (0.9843 – 0.9851)
31.000 – 31.025 (1.2205 – 1.2215)
32.955 – 32.980 (1.2974 – 1.2984)
42.950 – 42.975 (1.6909 – 1.6919)
30.970 – 30.995 (1.2193 – 1.2203)
24.959 – 24.980 (0.9826 – 0.9835)
30.950 – 30.975 (1.2185 – 1.2195)
0.020 – 0.070 (0.0008 – 0.0028)
0.025 – 0.075 (0.0010 – 0.0030)
0.015 – 0.065 (0.0006 – 0.0026)
0.020 – 0.062 (0.0008 – 0.0024)
0.025 – 0.075 (0.0010 – 0.0030)
29.985 – 30.006 (1.1805 – 1.1813)
40.007 – 40.028 (1.5751 – 1.5759)
28.000 – 28.021 (1.1024 – 1.1032)
21.985 – 22.006 (0.8655 – 0.8664)
29.957 – 29.970 (1.1794 – 1.1799)
39.975 – 39.991 (1.5738 – 1.5744)
27.967 – 27.980 (1.1011 – 1.1016)
21.952 – 21.965 (0.8643 – 0.8648)
0.015 – 0.049 (0.0006 – 0.0019)
0.016 – 0.053 (0.0006 – 0.0021)
0.020 – 0.054 (0.0008 – 0.0021)
0.020 – 0.054 (0.0008 – 0.0021)
12.000 – 12.018 (0.4724 – 0.4731)
5.93 – 6.00 (0.233 – 0.236)
11.957 – 11.968 (0.4707 – 0.4712)
STANDARD
0.15 – 0.35 (0.006 – 0.014)
–
–
0.019 – 0.037 (0.0007 – 0.0015)
73.000 – 73.015 (2.8740 – 2.8746)
–
–
–
72.976 – 72.990 (2.8731 – 2.8736)
18.010 – 18.013 (0.7091 – 0.7092)
17.996 – 18.000 (0.7085 – 0.7087)
0.010 – 0.017 (0.0004 – 0.0007)
0.15 – 0.30 (0.006 – 0.012)
0.30 – 0.42 (0.012 – 0.017)
0.20 – 0.70 (0.008 – 0.028)
0.035 – 0.080 (0.0014 – 0.0032)
0.030 – 0.055 (0.0012 – 0.0022)
0.010 – 0.039 (0.0004 – 0.0015)
17.964 – 17.977 (0.7072 – 0.7078)
0.026 – 0.044 (0.0010 – 0.0017)
GENERAL INFORMATION
Unit: mm (in)
SERVICE LIMIT
33.04 (1.301)
43.04 (1.694)
31.06 (1.223)
25.03 (0.985)
31.04 (1.222)
32.93 (1.296)
42.93 (1.690)
30.94 (1.218)
24.94 (0.982)
30.93 (1.218)
0.10 (0.004)
0.11 (0.004)
0.10 (0.004)
0.09 (0.004)
0.11 (0.004)
30.03 (1.182)
40.038 (1.5763)
28.04 (1.104)
22.02 (0.867)
29.93 (1.178)
39.965 (1.5734)
27.95 (1.100)
21.94 (0.864)
0.09 (0.004)
0.10 (0.004)
0.08 (0.003)
0.08 (0.003)
12.03 (0.474)
5.9 (0.23)
11.95 (0.470)
Unit: mm (in)
SERVICE LIMIT
0.45 (0.018)
0.03 (0.001)
0.03 (0.001)
0.05 (0.002)
73.07 (2.877)
0.10 (0.004)
0.10 (0.004)
0.10 (0.004)
72.970 (2.8728)
18.023 (0.7096)
17.988 (0.7082)
0.035 (0.0014)
0.6 (0.02)
0.6 (0.02)
0.8 (0.03)
0.15 (0.006)
0.13 (0.005)
0.05 (0.002)
17.985 (0.7081)
0.05 (0.002)
1-11