Omron NX701-17 Series Troubleshooting Manual page 118

3 Error Tables
Event code Event name
54014805 hex Communications
Timeout
(Ver. 1.12 or
later)
54014806 hex Invalid Mode
(Ver. 1.12 or
later)
54014807 hex I/O Power OFF
Status
(Ver. 1.12 or
later)
54014808 hex Verification Error
(Ver. 1.12 or
later)
54015420 hex Electronic Gear
Ratio Numerator
Setting Out of
Range
54015421 hex Electronic Gear
Ratio Denomina-
tor Setting Out of
Range
54015422 hex Target Velocity
Setting Out of
Range
54015423 hex Acceleration Set-
ting Out of Range
54015424 hex Deceleration Set-
ting Out of Range
54015425 hex Jerk Setting Out of
Range
54015427 hex Torque Ramp Set-
ting Out of Range
54015428 hex Master Coefficient
Scaling Out of
Range
54015429 hex Slave Coefficient
Scaling Out of
Range
5401542A hex Feeding Velocity
Setting Out of
Range
3-40
Meaning
A timeout occurred in com- • The communications
munications.
• The cable for Ether-
• Noise
• Device failure
The specified IO-Link mas- • The specified IO-Link
ter port is not the IO-Link
mode.
The I/O power is not sup- • The I/O power is not
plied to the specified IO-
Link master port.
The specified IO-Link mas- • The specified IO-Link
ter port had a verification
error or a communications
error.
The parameter specified for • Instruction input
the RatioNumerator input
variable to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the RatioDenominator input
variable to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the Velocity input variable
to a motion control instruc-
tion is out of range.
The parameter specified for • Instruction input
the Acceleration input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the Deceleration input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the Jerk input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the TorqueRamp input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the MasterScaling input
variable to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the SlaveScaling input vari-
able to a motion control
instruction is out of range.
The parameter specified for • The Feed Velocity
the FeedVelocity input vari-
able to a motion control
instruction is out of range.
Assumed cause
Maj Prt
timeout time is shorter
than the message
response time.
CAT or for IO-Link is
broken.
master port is not the
IO-Link mode.
supplied to the speci-
fied IO-Link master
port.
master port had a veri-
fication error or a com-
munications error.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
(input variable Feed-
Velocity) is still at the
default (0).
NJ/NX-series Troubleshooting Manual (W503)
Level
Refer-
ence
Min Obs Info
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502
S W502