Checking Vtr/Disk Recorder/Extended Vtr Information - Sony MVS-6520 User Manual

recording starts at the position in the same file where
recording was interrupted.
To stop recording
Press the [STOP] button or the [ALL STOP] button in the
device control block.
Checking VTR/Disk Recorder/
Extended VTR Information
You can check the following information using the Device
>DDR/VTR >Cueup & Play menu (5331).
DEV (device name): DEV1 to DEV12 represent
respectively device 1 to device 12.
Reg (register): Number of the register to which settings
apply.
Status: Status of each device.
Operating When VTR is used When video disk
status
display
XXXX Communications
with the device are
being carried out
normally, but status
information is not
received.
Local The REMOTE/
LOCAL switch of
the device is set to
LOCAL.
Tape Out No tape is loaded.
Rec Recording.
Cue> Cueing up in the
forward direction.
Cue< Cueing up in the
reverse direction.
Eject Ejecting cassette.
Stb Off
Stopped in standby
off mode.
Stop Stopped in standby
on mode.
Play Playing.
FF Fast forwarding.
Rewind Rewinding.
Shtl> Playing in the
forward direction in
shuttle mode.
Shtl<
Playing in the
reverse direction in
shuttle mode.
Var> Playing in the
forward direction in
variable mode.
232
Control of VTRs, Extended VTRs, and Disk Recorders
Current: Shows timecode for current device position.
Start TC: Shows timecode for start point set on device.
Stop TC: Shows timecode for stop point set on device.
Variable: Shows the variable speed set for each device.
communications,
Delay: Shows start delay time set on device.
Extended VTR, or
Mode: Shows operation mode (Loop or Recue) set for
Sony disk 9-pin
protocol is used
Not
communicating, or
Cueup & Play
communicating but
the device type
cannot be read.
You can use the device control block or Device menu to
save Cueup & Play settings (start point timecode, stop
Port is not open.
point timecode, start delay time, and so on) for a VTR, disk
recorder or Extended VTR in an effect register. By
recalling this register, you can operate the following
buttons in the Flexi Pad to automatically control the VTR,
No file loaded.
disk recorder or Extended VTR.
a)
Recording.
[REWIND] button: Cue up to the start point timecode
–
[RUN] button: Play
With this function you can also stop the VTR, disk
–
recorder or Extended VTR used for playback at the stop
point timecode recalled from the same register.
–
Disk recorder (video disk communications
–
protocol) operation when loop /recue is set
When loop is set: Plays repeatedly between the start point
Stopped.
When recue is set: Automatically cues up the start point
Playing.
–
–
Notes
–
• In an effect register set on the VTR/disk recorder
timeline, Cueup & Play settings are not possible. To add
Cueup & Play settings to such a register, first clear the
–
VTR/disk recorder timeline setting before carrying out
the operation.
• When using a disk recorder with Cueup & Play, if you
Playing in the
carry out the following sequence of operations, the
forward direction in
system may freeze on the frame of the start point.
variable mode.
Operating When VTR is used When video disk
status
display
Var< Playing in the
reverse direction in
variable mode.
Jog> Playing in the
forward direction in
jog mode.
Jog< Playing in the
reverse direction in
jog mode.
Still Playing still image.
a) Not supported by Extended VTR.
each device.
and stop point.
when play reaches the stop point.
communications,
Extended VTR, or
Sony disk 9-pin
protocol is used
Playing in the
reverse direction in
variable mode.
Playing in the
forward direction in
jog mode.
Playing in the
reverse direction in
jog mode.
–