Hakko Electronics Monitouch V9 Series Connection Manual page 293

16-40 16. Fuji Electric
Address
47zz
48zz
49zz
50zz
51zz
52zz
53zz
54zz
55zz
56zz
57zz
58zz
59zz
60zz
61zz
62zz
63zz
64zz
65zz
66zz
67zz
68zz
69zz
70zz
71zz
72zz
73zz
74zz
75zz
76zz
77zz
78zz
79zz
80zz
81zz
82zz
83zz
84zz
F-MPC04/F-MPC04P/F-MPC04S
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
(Blank)
FePSU F-MPC30/F-MPC50/F-MPC55V/F-MPC60B
(Blank) Reverse phase relay
(Blank) Demand average time
Year setting
CB opening jam monitoring time
Month setting
CB closing jam monitoring time
Monitoring trip coil TC disconnection, OFF
Date setting
expedited, function application setting
Hour setting
kWh pulse constant
Minute setting
kvarh pulse constant
(Blank) Selective input 1 function setting
(Blank) Selective input 2 function setting
(Blank) Selective input 3 function setting
(Blank) Selective input 4 function setting
(Blank) Selective input 5 function setting
(Blank) Selective input 6 function setting
(Blank) Selective input 7 function setting
(Blank) Selective input 8 function setting
(Blank) Device fault detection function setting
(Blank) Fault pick-up output setting
(Blank) Transmission component 1 output setting
(Blank) Transmission component 2 output setting
(Blank) Distant/direct state output setting
(Blank) Transducer output current phase setting
(Blank) Transducer output voltage phase setting
Residue/CT 3rd selection (zero-phase
(Blank)
current)
(Blank)
Protective INST (phase N) (current setting)
(Blank) Protective INST (phase N) (output setting)
(Blank) Protective OC (phase N) (current setting)
(Blank) Protective OC (phase N) (characteristic)
Protective OC (phase-N) (time
(Blank)
magnification)
(Blank) Protective OC (phase N) (output setting)
Protective OCA overcurrent pre-alarm
(Blank)
(phase N) (current setting)
Protective OCA overcurrent pre-alarm
(Blank)
(phase N) (operation time)
Protective OCA overcurrent pre-alarm
(Blank)
(phase N) (output setting)
(Blank) Protective OCGA pre-alarm (current setting)
(Blank) Protective OCGA pre-alarm (operation time)
(Blank) Protective OCGA pre-alarm (output setting)
(Blank) Protective DT2 (current setting)
(Blank)
Protective DT2 (operation time)
(Blank) Protective DT2 (output setting)
*3
*3
*5
*5
*2
*2
*2