Hakko Electronics Monitouch V9 Series Connection Manual page 291

16-38 16. Fuji Electric
F*JF-R
Communication setting
The communication parameters can be set using keys attached to the front of the digital regular electricity meter.
Be sure to match the settings to those made under [Communication Setting] of the editor.
Type
Communication
setting
* The communication parameter (stop bit) is fixed to 1 bit.
Available Device Memory
The available setting range of device memory varies depending on the model. Be sure to set within the range available for the
model to be used. Use [TYPE] when assigning indirect device memory for macro programs.
00
(data request of circuit No. 1 to 4)
01
(data request of circuit No. 5 to 8)
02
(data request of circuit No. 9, 10 or E)
(Data request of the minimum/maximum voltage, power factor of circuit 1 to 10, and
03
invalid power)
09 (model code)
10 (operation status)
11
(pre-alarm value)
12
(current value measurement data)
13
(integrated value data)
14
(demand measurement data)
15
(data of a maximum value of demand measurement)
16
(historical data 1)
17 (historical data 2)
18
(setting data)
*1 When a device memory other than status is used, set the decimal point of the numerical display part to "3".
*2 "0" is stored in the address for which "(Blank)" is indicated in the table below.
*3 For setting data, see "18 (Setting Data)" described below.
18 (Setting Data)
Address
00zz
01zz
02zz
03zz
04zz
05zz
06zz
07zz
08zz
09zz
10zz
11zz
Item
Address
Baud Rate
Data Length
Parity Bit
Device Memory
*1
*1
*1
*1 *2
*1
*1 *2
*1 *2
*1 *2
*1 *2
*3
F-MPC04/F-MPC04P/F-MPC04S
Wiring method (voltage measured)
*1
Ratio of VT 1 (primary voltage)
Ratio of VT 1 (secondary voltage)
Demand average time
Frequency
Number of applicable circuits
Pulse multiplying factor
*1
Ratio of VT 2 (primary voltage)
Ratio of VT 2 (secondary voltage)
Number of turns for CT2 secondary line
*1
CT primary current
OCG sensitivity current
Setting
01 - 99
4800bps / 9600bps / 19.2 kbps
7 / 8 bits
None / Even / Odd
*1 *2
FePSU
(Blank)
(Blank)
*1
(Blank)
Demand average time
(Blank)
(Blank)
(Blank)
(Blank)
*1
(Blank)
(Blank)
(Blank)
(Blank)
(Underlined setting: default)
Example
01
19.2 kbps
7 bits
Odd
TYPE Remarks
00H Double-word, read only
01H Double-word, read only
02H Double-word, read only
03H Double-word, read only
09H Read only
0AH Read only
0BH Double-word, read only
0CH Double-word, read only
0DH Double-word, read only
0EH Double-word, read only
0FH Double-word, read only
10H Double-word, read only
11H Double-word, read only
12H Double-word
F-MPC30/F-MPC50/F-MPC55V/F-MPC60B
CT primary rated current
Ratio of VT (primary voltage)
Ratio of VT (secondary voltage)
Rated frequency
*2
Protective INST (current setting)
Protective INST (output setting)
*2
Protective DT (current setting)
*2
Protective DT (operation time)
*2
Protective DT (output setting)
Protective OC (current setting)
Protective OC (characteristic)
Protective OC (time magnification)
*2