Operating Notes - Yamaha CS1D Operating Manual

Important
Read the following before operating the CS1D
Warnings
Do not allow water to enter this unit or allow the
unit to become wet. Fire or electrical shock may
result.
Connect this unit's power cord only to an AC outlet
of the type stated in this Owner's Manual or as
marked on the unit. Failure to do so is a fire and elec-
trical shock hazard.
Do not place heavy objects, including this unit, on
top of the power cord. A damaged power cord is a
fire and electrical shock hazard. In particular, be
careful not to place heavy objects on a power cord
covered by a carpet.
Do not modify the unit. Doing so is a fire and electri-
cal shock hazard.
Do not place a container with liquid or small metal
objects on top of this unit. Liquid or metal objects
inside this unit are a fire and electrical shock hazard.
Cautions
This unit has ventilation holes at the top and bottom
to prevent the internal temperature rising too high.
Do not block them. Blocked ventilation holes are a
fire hazard.
Since this device is heavy, please use an appropriate
number of people (two or more) when moving it.
Before moving the CS1D, you must be sure to lower
the display toward the back until it is fastened in
position.

Operating Notes

The digital circuits of this unit may induce a slight
noise into nearby radios and TVs. If noise occurs,
relocate the affected equipment.
Handling the included PM1D System Software disc
The included PM1D System Software Disc is CD-R media containing documentation and software for the PM1D.
A computer with a connected CD drive is required in order to use this documentation and software.
For details on the contents, refer to the documentation on the disc.
Please observe the following points when handling the disc.
Failure to do so may cause problems such as the recorded data being lost, the drive to malfunction, or the printed label to
become blurred.
Do not place the disc in locations of direct sunlight,
high temperature, or high humidity.
Do not touch either surface of the disc.
Hold the disc at the edges. Gently wipe dust or dirt
off of the recording surface of the disc.
ii
Using a mobile telephone near this unit may induce
noise. If noise occurs, use the telephone away from
the unit.
XLR-type connectors are wired as follows: pin 1:
ground, pin 2: hot (+), and pin 3: cold (–).
If the message "WARNING LOW BATTERY !"
appears when you turn on this unit, contact your
dealer as soon as possible about replacing the inter-
nal data backup battery. The unit will still operate
correctly, but data other than the presets will be lost.
We recommend that you save the data on an ATA-
compatible PC flash storage card before replacing the
battery.
The performance of components with moving con-
tacts, such switches, rotary controls, faders, fans, and
connectors, deteriorates over time. The rate of dete-
rioration depends on the operating environment and
is unavoidable. Consult your dealer about replacing
defective components.
The CS1D is cooled by fan exhaust openings located
on its rear panel. Check these regularly and use a vac-
uum cleaner etc. to ensure that the openings do not
become clogged with dust. Before performing this
maintenance, you must turn off the POWER switch
of the PM1D power supply unit and make sure that
the CS1D is not operating.
The power must be turned on/off using the POWER
switch of the PW1D power supply unit. Do not turn
the power on/off by plugging in the power cable, or
by using a power strip or circuit breaker. Doing so
may cause malfunctions.
Do not rapidly turn on and off the POWER switch of
the PW1D power supply unit. Doing so may cause
excessive current to damage the system. You must
allow at least five seconds to elapse between power-
on and power-off.
Do not wipe the disc with chemicals or detergents.
Do not bend or drop the disc.
Use an air duster or cleaner to remove dust. Vigor-
ously rubbing the surface of the disc with a dry cloth
may scratch the disc.