Page 1 Owner’s Manual...
Page 2 300 ohm ribbon lead, change the lead-in to coaxial type cable. If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA 90620 The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
Page 3: Operating Notes
(two or more) when moving it. uum cleaner etc. to ensure that the openings do not • Before moving the CS1D, you must be sure to lower become clogged with dust. Before performing this the display toward the back until it is fastened in posi- maintenance, you must turn off the POWER switch of tion.
Page 4 Copyright No part of the CS1D software or this Owner’s Manual may be reproduced or distributed in any form or by any means without the prior written authorization of Yamaha Corporation. © 2000 Yamaha Corporation. All rights reserved.
Page 5 Operating Manual...
Page 6 Operating Manual (Start-up)
Page 7: Table Of Contents
Introduction .........1 About the “CS1D Operating Manual (Start-up)” ......1 Printing conventions in “CS1D Operating Manual (Start-up)”.
Page 8 Contents Basic settings (Mirror mode) ......26 Selecting the operation mode (Mirror mode) ......26 Setting the word clock (Mirror mode) .
Page 9: Introduction
Introduction About the “CS1D Operating Manual (Start-up)” The “CS1D Operating Manual (Start-up)” is an introductory manual that explains how to connect the various compo- nents of the PM1D system and verify that the PM1D system is operating correctly. When starting up the PM1D system for the ﬁrst time, or if you have changed the conﬁguration of the system such as when the PM1D system has been moved to another location and/or re-connected, we recommend that you follow the procedure described in this manual to verify that the system is operating correctly.
Page 10: Introducing The Various Components
48CH 96CH POWER cards installed Cards can be installed in the AI8 only by a Yamaha service engineer. The user must never attempt to install a card himself. Analog output unit (AO8) This is an output unit that outputs analog audio signals...
Page 11 Introducing the various components It is not possible to install and use a total of five or more AP8AD/AP8DA cards. Also, if you are using AP8AD/AP8DA cards simultaneously with MY8- AD/MY4-AD/MY4-DA cards, there are restrictions on the number of cards, as described below. Never exceed the allowable number of cards, since attempting to use a greater number of cards than allowed may damage the DIO8 due to excessive...
Page 12: Terms Used In The "Cs1D Operating Manual (Start-Up)
Terms used in the “CS1D Operating Manual (Start-up)” Of the specialized terms used in operating the CS1D, this section will explain the terms that appear in “CS1D Operating Manual (Start-up).” For a more detailed explanation of terms, refer to “CS1D Operating Manual (Basic Operation).”...
Page 13 Hint As an alternative way to perform this action, you can use a mouse connected to the MOUSE connector of the CS1D. Mouse Track pad Drag Drag...
Page 14: Connections (Standard Mode)
Connections (Standard mode) This section explains connections for Standard mode, in which one console (CS1D) is connected to one engine (DSP1D- EX {DSP1D}). Connecting the console and engine (Standard mode) The following diagram shows typical connections between the console and engine for Standard mode.
Page 15 Use the included special cable to connect the DC POWER INPUT connector of the console to the DC Use only Yamaha-manufactured D-sub half pitch 68 OUTPUT connector of the PW1D power supply. pin cables to connect the digital input/output con- nectors.
Page 16: Connecting An Analog Input/Output Unit To The Engine
CS1D Operating Manual (Start-up) Connecting an analog input/output unit to the engine (Stan- dard mode) The following diagram shows a common way of making connections between the engine and analog input/output units for Standard mode. INPUT 2 OUTPUT 2 ENGINE A...
Page 17: Mode)
Connections (Standard mode) Connecting a digital input/output unit to the engine (Standard mode) When connecting a DIO8 digital input/output unit to the engine in Standard mode, the method will depend on whether you use only slots 1–4 (of the DIO8’s slots 1–8) or slots 1–4 as well as slots 5–8. 1 If input/output cards are installed only in DIO8 2 If input/output cards are also installed in DIO8 slots 1–4...
Page 18: Connections (Mirror Mode)
Connections (Mirror mode) This section explains connections for Mirror mode, in which one console (CS1D) is connected to two engines (DSP1D- EX {DSP1D}). Connecting the console and engines (Mirror mode) The following diagram shows typical connections between the console and engines for Mirror mode.
Page 19 RS-232-C RS-232-C RS-422 RS-422 riences difﬁculties. Console (CS1D) In order to minimize the clock switching time in such cases, we recommend that you supply a word WORD CLOCK WORD CLOCK clock from an external clock generator to the con- sole and to engines A/B.
Page 20: Connecting An Analog Input/Output Unit To The Engines (Mirror Mode)
CS1D Operating Manual (Start-up) Connecting an analog input/output unit to the engines (Mirror mode) The following diagram shows a common way of making connections between the engine and analog input/output units for Mirror mode. WORD CLOCK IN INPUT 2 OUTPUT 2...
Page 21: Connecting A Digital Input/Output Unit To The Engines (Mirror Mode)
Connections (Mirror mode) Connecting a digital input/output unit to the engines (Mirror mode) The following diagram shows the usual method of connecting the engines to a digital input/output unit in Mirror mode. WORD CLOCK IN ENGINE A (DSP1D-EX{DSP1D}) INPUT 1 OUTPUT 1 OUTPUT A INPUT A...
Page 22: Turning On The Power And Verifying The Connections
The “PM1D Operating Manual (Start-up)” assumes that the various internal settings of the CS1D are in their default state. If you have already modiﬁed the settings of the CS1D from their initial state, or if you are not sure whether the...
Page 23: Checking The Status Of Each Device (Standard Mode)
Turning on the power and verifying the connections If the opening screen is followed by the “VERSION CHECK” popup window, it is possible that the PM1D system version is incorrect. Please unify the software version of all connected devices. For the procedure, refer to the expla- nation within the included PM1D System Software disc.
Page 24: Checking The Analog Input Unit (Standard Mode)
PM1D system. Check the connection for the WORD CLOCK IN connector of the AI8, or the CS1D word clock settings ( p.24). UC (unconnected) Control signals are not being received correctly. Make sure that the engine is powered-on.
Page 25: Checking The Analog Output Unit (Standard Mode)
Check the connection for the E2 ......The AO8 is connected to an WORD CLOCK IN connector of INPUT connector of the engine. the AO8, or the CS1D word Re-connect it to an OUTPUT clock settings ( p.24). connector. UC (unconnected) . Control signals are not being E3 ......The cable connected to the...
Page 26: Checking The Status Of Each Device (Mirror Mode)
(digital input/output the CONTROL I/O connections between the connectors, control input/output connectors). DSP1D-EX {DSP1D} and the CS1D. If both LEDs are dark, digital signals or control sig- 3 INPUT CONFIGURATION nals are not being passed between the engine and This indicates the number of monaural input chan- the console.
Page 27: Checking The Analog Input Unit (Mirror Mode)
Make sure that the engine is powered-on. ID number and A (or b) displayed alternately Since control signals from the CS1D forcibly switched the valid engine to A (or B), the setting of the CONTROL INPUT SELECTOR switch of the AI8 does not match the actual operation.
Page 28: Checking The Analog Output Unit (Mirror Mode)
A (or B), the setting of the INPUT SELECTOR switch of the AI8 does not match the actual operation. This display does not signify an actual error. How- ever as necessary, check the setting of the INPUT SELECTOR switch or the setting of the CS1D.
Page 29: Checking The Digital Input/Output Unit (Mirror Mode)
CS1D ( p.28). ID number and A (or b) displayed alternately Since control signals from the CS1D forcibly switched the valid engine to A (or B), the setting of the PORT B SELECTOR switch of the DIO8 does not match the actual operation.
Page 30: Basic Settings (Standard Mode)
Basic settings (Standard mode) When starting up the PM1D system for the ﬁrst time, you will need to select the operation mode of the PM1D (which is what determines the system conﬁguration and how the components are connected to each other), and set the word clock that will be shared by the entire system.
Page 31 At this time, noise may be produced from the output jacks of the CS1D or AO8 (in particular if an MY8-AT digital I/O card is installed in the DIO8). In order to protect your speakers, you must turn down the output of the power amp before changing this setting.
Page 32: Setting The Word Clock (Standard Mode)
CS1D Operating Manual (Start-up) Setting the word clock (Standard mode) In order for the PM1D system to function, word clock (audio system clock) synchronization must be established between all devices of the system. In this screen you can specify the word clock that will operate the PM1D system. In general, the frequency of this clock is referred to as the sampling rate or sampling frequency.
Page 33 When you change the word clock settings, noise may be heard from the output jacks of the CS1D and AO8, particularly if an MY8-AT digital I/O card is installed in the DIO8. To protect your...
Page 34: Basic Settings (Mirror Mode)
Basic settings (Mirror mode) This section explains how to select the operation mode and word clock master when using the PM1D system in Mirror mode. Selecting the operation mode (Mirror mode) [Procedure] 1. In the LCD FUNCTION ACCESS block, press the [SYS/W.CLOCK] switch several times to access the following screen.
Page 35 When you perform this switch, the word clock will be reset. At this time, noise may be produced from the output jacks of the CS1D or AO8 (in particular if an MY8-AT digital I/O card is installed in the DIO8). In order to protect your speakers, you must turn down the output of the power amp before changing this setting.
Page 36: Setting The Word Clock (Mirror Mode)
CS1D Operating Manual (Start-up) Setting the word clock (Mirror mode) This section explains how to check whether the word clock settings are appropriate when using the PM1D system in mir- ror mode. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the [SYS/W.CLOCK] switch several times to access the...
Page 37 Basic settings (Mirror mode) 3. Make sure that the master word clock and the word clock input select are set as follows. MASTER CLOCK SELECT The W.CLOCK of the engine or console is on WORD CLOCK INPUT SELECT Console W.CLOCK IN Engine A/B W.CLOCK IN Each unit...
Page 38: Checking The Operation Of Input Units
Connect a monitor system (or headphones) to the MONITOR OUT A jacks of the console (or to the MONITOR A headphone jack) m m m m Turn on the power in the order of input unit DSP1D-EX {DSP1D} engine CS1D console monitor system m m m m Patch the input unit to an input channel m m m m...
Page 39: Connect The Monitor System
In order to check the operation of an input unit, you must connect a monitor system such as powered monitor speakers or a power amp + speaker to the MONITOR OUT A jacks located on the rear panel of the CS1D console. (Since the pur- pose of this is to check the operation, high power monitors are not necessary.)
Page 40: Connect An Input Source
Connect an input source Connect one of the following input sources according to the type of input unit or card that you wish to check. To check a mic/line input card (LMY2-ML) To check an input channel of a digital I/O card installed in the AI8 (MY8-AT, MY8-TD, MY8-AE) installed in the DIO8 Connect a line output device such as a CD player or...
Page 41: Patch The Input Unit To An Input Channel
Simply connecting a source to an input unit does not cause that signal to be input to the PM1D system. In order to send signals to the PM1D system, you must assign (patch) the input jacks of the input unit to input channels of the PM1D sys- tem. This operation is performed within the display of the CS1D console. [Procedure] 1.
Page 42 CS1D Operating Manual (Start-up) Patch source input jack. From the top row, the dis- play shows the type and ID of the input unit, the num- ber of the slot in which the Number of input card is the patch...
Page 43 Checking the operation of input units Using the switches of the console Using the track pad of the console 1. Use the [CURSOR] switches in the data entry block 1. Use the track pad to move the cursor to the desired to move the cursor (the red frame) in the display to grid.
Page 44: Monitor The Input Signal
CS1D Operating Manual (Start-up) Monitor the input signal After you have patched an input source to an input channel, press the [CUE] switch for that input channel and check whether it is output from the MONITOR OUT jacks. [Procedure] 1. Play back the input source, and check that the...
Page 45 LAYER [49-96] switch is on (LED lit), channels 49–96 will be selected as the input channels that are controlled from the top panel of the CS1D. {This switch has no function on the 48 channel model.} To control channels 1–48, press the GLO- BAL LAYER [1-48] switch.
Page 46: Checking The Operation Of An Output Unit
Connect your monitor system to an output unit m m m m Turn on the power in the order of input unit DSP1D-EX {DSP1D} engine CS1D console monitor system m m m m Patch the input unit to an input channel...
Page 47: Connect The Monitor System
Checking the operation of an output unit Connect the monitor system In order to check the operation of an analog output unit, you will need to connect a monitor system such as a set of pow- ered speakers or a power amp + speakers to a DA card (LMY4-DA) installed in the AO8 analog output unit. OUTPUT UNIT NO.
Page 48: Connect An Input Source
CS1D Operating Manual (Start-up) Connect an input source As a sound source for checking, connect a line output device such as a CD player or DAT recorder to an input unit. INPUT UNIT NO. PHANTOM MASTER AI8 analog input unit...
Page 49: Patch The Input Unit To An Input Channel
Checking the operation of an output unit Patch the input unit to an input channel Patch the input jack to which you connected the input source to input channels 1/2. For details of the procedure, refer to page 33. [Procedure] 1.
Page 50: Patch The Stereo A Channel To An Output Unit
MATRIX channel, STEREO A/B channel) of the PM1D system to the jacks of an output unit. This action is per- formed within the display of the CS1D console. Here’s how to patch the STEREO A channel output signal to the output unit to which your monitor system is connected.
Page 51 Checking the operation of an output unit Patch desti- nation out- put jacks. From the top, this area shows the type and ID of the output unit, Patch source the number output of the slot in channels. which the output card is installed, and the channel...
Page 52: Send The Input Signals Of Input Channels 1/2 To The Stereo Bus
CS1D Operating Manual (Start-up) Send the input signals of input channels 1/2 to the STEREO bus With the operations you have performed up to this point, the signals of the STEREO bus of the PM1D system will be output to the output jacks to which your monitor system is connected. Now we will send the signals of the input source to the STEREO bus to verify that they can be monitored via your monitor system.
Page 53 LAYER [49-96] switch is on (LED lit), channels 49–96 will be selected as the input channels that are controlled from the top panel of the CS1D. {This switch has no function on the 48 channel model.} To control channels 1–48, press the GLO- BAL LAYER [1-48] switch.
Page 54: Turn Off The Power
For the procedure of storing a scene, refer to “CS1D Reference Manual (Hardware)” ( p.89) or “CS1D Reference Manual (Software)”...
Page 55 Operating Manual (Basic Operation)
Page 56 User interfaces within the display........9 User interface on the top panel of the CS1D ......11 External user interfaces .
Page 57 Contents Basic operation INPUT blocks/ST IN block ......34 INPUT block/ST IN block controls and functions ..... . . 34 Head amp settings .
Page 58 Contents Inserting into an output channel ........89 Direct out .
Page 59 Contents Chapter 11. Talkback/Oscillator ..... . . 120 Talkback ............120 Oscillator .
Page 60: Chapter 1. Introduction
About the “CS1D Operation Manual (Basic Operation)” The “CS1D Operation Manual (Basic Operation)” explains basic operation of the PM1D system, such as connecting the input sources and playback system, operating the CS1D console, and using the display of the CS1D to make various set- tings.
Page 61: Overview Of The Pm1D System
Overview of the PM1D system The PM1D system is a full-digital SR mixing system that consists of a CS1D console, PW1D power supply, DSP1D-EX {DSP1D} DSP unit(s), AI8 analog input unit(s), AO8 analog output unit(s), DIO8 digital input/output unit(s), and input/output cards.
Page 62 ANALOG OUTPUT BOX Up to the number Total 4 card Up to 1 card of vacant DIO8 Cards must be installed in the AO8 by a Yamaha slots service engineer. Never attempt to install these Total 5 or more cards yourself.
Page 63: Signal Flow In The Pm1D System
ﬂow will be as shown on The signals that are input from the 2-TRACK IN the next page. DIGITAL jacks 1–6 and 2-TRACK IN ANALOG jacks 1/2 of the CS1D can also be sent to the engine.
Page 64 Chapter 1. Introduction ADAT digital MTR ADAT INPUT I/O UNIT ID OUTPUT PORT B SELECTOR POWER DIO8 digital input/output unit DSP1D-EX {DSP1D} INPUT OUTPUT 1~10 engine...
Page 65: Number Of Inputs/Outputs And Channel Structure
CS1D Operating Manual (Basic Operation) Number of inputs/outputs and channel structure The DSP1D-EX {DSP1D} engine provides INPUT connectors 1–10 for connecting input units, and OUTPUT connec- tors 1–6 for connecting output units. When the PM1D system is used in Standard mode, up to ten input units (maximum of 320 input connectors) and up to six output units (maximum of 192 output connectors) are connected to one engine.
Page 66 Chapter 1. Introduction In either mode, the input connectors of an input unit must be assigned (patched) in the CS1D display to an input chan- nel in order to be used. Similarly, in order to use the output connectors of an output unit, you must assign them in the display to an output channel (MIX channel, MATRIX channel, STEREO A/B channel).
Page 67: Mix Buses/Matrix Buses
A/B. Of course, switching will occur even without this type of supply method. Hint For details on selecting the word clock master, refer to “CS1D Operation Manual (Start-up)” ( p.24) and to “CS1D Reference Manual (Software)” ( p.44). Hint As an exception, the 2-TRACK IN DIGITAL jacks 1–6 of the CS1D console have built-in sample rate converters, and...
Page 68: Chapter 2. The User Interfaces Of The Cs1D
The PM1D system is designed so that basic parameters such as channel adjustments and mixing can be controlled using only the faders and encoders on the top panel of the CS1D. However if you wish to make more detailed settings, you will need to access a speciﬁc function and edit the parameter value in software.
Page 69 CS1D Operating Manual (Basic Operation) Text input box These boxes are used to input characters/numerals/ symbols when assigning a name to a channel or scene, etc. Character palette This is a virtual keyboard used to input characters/ numerals/symbols into a text input box.
Page 70: User Interface On The Top Panel Of The Cs1D
Chapter 2. The user interfaces of the CS1D User interface on the top panel of the CS1D The top panel of the CS1D provides the following controls used for operations in the display. LCD FUNCTION ACCESS block The LCD FUNCTION ACCESS block contains switches used to access the desired function or screen in the display.
Page 71: External User Interfaces
A PS/2 compatible mouse can be connected to the is according to the English-language keyboard.) MOUSE connector on the rear panel/top panel of the Function CS1D, and used in the same way as the track pad. Same function as the [DEC/CANCEL] PageDown switch of the data entry block...
Page 72 If a PS/2 compatible numeric keypad is connected to the NUM KEY connector located on the rear panel or top panel of the CS1D, you can use the keypad to input numbers and recall scenes. The function of each key is as follows.
Page 73: Various Basic Operations
CS1D Operating Manual (Basic Operation) Various basic operations This section explains the basic operations performed in the CS1D display. In general, operations in the CS1D software will consist of combinations of these actions. Click “Click” is the action of moving the pointer to a speciﬁc item in the screen, and pressing the left or right switch of the track pad (or if using an external mouse, pressing the left or right mouse button).
Page 74: Drag And Drop
Chapter 2. The user interfaces of the CS1D Drag and drop “Drag and drop” is the action of moving the pointer to a speciﬁc item in the screen, dragging it to another location in the screen, and then releasing your ﬁnger. Drag and drop is used (for example) to copy EQ or dynamics processor settings to another channel.
Page 75: Accessing The Desired Screen
CS1D Operating Manual (Basic Operation) Accessing the desired screen There are two ways to access the desired function/screen in the display. Using the LCD FUNCTION ACCESS block Using the buttons within the display [Procedure] [Procedure] 1. Of the switches in the LCD FUNCTION ACCESS 1.
Page 76: Button Operations
Chapter 2. The user interfaces of the CS1D Button operations Buttons within the display are used to turn speciﬁc parameters on/off, or to choose one of multiple choices. Buttons can be operated in the following ways. Using the track pad (mouse)
Page 77: Moving The Cursor
CS1D Operating Manual (Basic Operation) Moving the cursor Here’s how to move the cursor (red box) in order to select the display parameter that you wish to edit. Moving the cursor Moving the cursor from a scroll window [Procedure] [Procedure] 1.
Page 78: Adjusting The Value Of A Knob Or Fader
Chapter 2. The user interfaces of the CS1D Adjusting the value of a knob or fader Knobs and faders within the display are used to adjust the value of speciﬁc parameters. Knobs and faders can be adjusted in the following ways.
Page 79: Assigning A Name
CS1D Operating Manual (Basic Operation) Assigning a name The PM1D system allows you to assign names (long name, short name) to individual channels, and to assign titles to scenes and libraries. For example, the screen shown below is the LIBRARY STORE popup window in which you can name and store a library.
Page 80 Chapter 2. The user interfaces of the CS1D buttons..Move the highlighted area to left √ ® or right. PASTE button ..The text string that had been copied to the buffer by the COPY button will be pasted. COPY button ..The speciﬁed text string will be copied from the text box into the buffer.
Page 81: Chapter 3. Audio Connections And Patching
CS1D console, and patch them to input channels and output channels. The “CS1D Operation Manual (Basic Operation)” assumes that the components of the PM1D system are connected appropriately, and that all components are operating correctly. For details on connecting the components of the PM1D system and checking their operation, refer to the “CS1D Operation Manual (Start-up).”...
Page 82 Chapter 3. Audio connections and patching AD card (LMY4-AD) The LMY4-AD provides four channels of XLR-3-31 (balanced) input jacks that can be used simulta- neously. LMY4-AD connections INPUT UNIT NO. AI8 analog input unit PHANTOM MASTER +48V POWER ANALOG INPUT BOX AD-Platine (LMY4-AD) Rhythm machine...
Page 83: Audio Connections For An Analog Output Unit
CS1D Operating Manual (Basic Operation) Audio connections for an analog output unit An LMY4-DA DA card installed in the AO8 analog output unit provides four channels of XLR-3-32 (balanced) output jacks. LMY4-DA connections OUTPUT UNIT NO. INPUT SELECTOR AO8 analog output unit...
Page 84: Audio Connections For A Digital Input/Output Unit
Chapter 3. Audio connections and patching Audio connections for a digital input/output unit The DIO8 digital input/output unit can accommodate up to eight digital I/O cards or analog I/O cards, according to your system. The following diagrams show examples of connecting the DIO8 to digital recorders in ADAT, Tascam, and AES/EBU formats.
Page 85: Audio Connections For The Console
In the PM1D system, most of the signal processing is performed in the input/output units and in the engine, and the console simply controls their operation. However as exceptions, the CS1D also has the following input/output jacks. 2-TRACK IN DIGITAL AES/EBU jacks (1–6)
Page 86 TALKBACK IN 2 jack (rear panel) These are XLR-3-31 (balanced) jacks for connecting talkback mics. These two jacks can be used simulta- neously. Audio connections for the console 3 CS1D top panel Talkback mic TALKBACK IN 2 CS1D rear panel...
Page 87: Patching
PM1D system. Hint As exceptions, patching is not necessary for the output jacks of the CS1D console itself (the STEREO OUT DIGITAL AES/EBU, STEREO OUT DIGITAL COAXIAL, MONITOR OUT ANALOG, and CUE OUT ANALOG jacks).
Page 88 Chapter 3. Audio connections and patching 2. Use the horizontal scroll bar to access the patch number. To view a unit/card/input jack that is not source input unit. currently visible, use the horizontal scroll bar. The horizontal axis of the screen shows the input unit ID number/card slot number/input jack channel From above, this indicates the type and number of input unit/...
Page 89: Output Channel Patching
The short name you assign to each channel will be displayed in various screens of the display and in the Hint [NAME] indicator of the CS1D console. If you wish to assign names to numerous channels at once, it is convenient to use the IN PATCH function NAME screen.
Page 90 The horizontal axis of the screen shows the output displayed in various screens of the display and in the unit ID number/card slot number/input jack channel [NAME] indicator of the CS1D console. number. To view a unit/card/input jack that is not currently visible, use the horizontal scroll bar.
Page 91: Chapter 4. Basic Operation For Input Channels
EQ/compressor/gate, and is sent to the STEREO bus or MIX bus. The following blocks on the CS1D console are used to control input channels. INPUT blocks 1–4 SELECTED INPUT CHANNEL block These blocks adjust the pan and level etc.
Page 92: Changing The Channel Assignments
Chapter 4. Basic operation for input channels Changing the channel assignments When the PM1D system is in its default state, INPUT blocks 1–4 are assigned input channels 1–12, 13–24, 25–36, and 37–48 respectively. Similarly, ST IN channels 1–4 are assigned to the ST IN block. However, you can change these assignments by using the SELECTED INPUT CHANNEL block MODULE [FLIP] switch and the MASTER block GLOBAL LAYER [1-48]/[49-96] switches, as described below.
Page 93: Basic Operation Input Blocks/St In Block
This LED will light when the input signal clips for that These LEDs show the operating status of the inter- input channel. nal compressor. For details on the meaning of each LED, refer to “CS1D Reference Manual (Software).” COMP GATE [+]/[THR]/[–] LEDs INPUT [SEL] switch and LED...
Page 94 These LEDs show the operating status of the inter- ST IN channel. nal compressor. For details on the meaning of each LED, refer to “CS1D Reference Manual (Software).” ST IN SEL [L]/[R] switches and LEDs COMP These switches select the channel (L or R of the corre- GATE [+]/[THR]/[–] LEDs...
Page 95: Head Amp Settings
CS1D Operating Manual (Basic Operation) Head amp settings For channels to which a mic/line amp card (LMY2-ML) has been patched, you must complete various settings for the head amp (e.g., select input jacks A/B, turn phantom power on/off) before you continue.
Page 96 Chapter 4. Basic operation for input channels If you wish to use phantom power, you must also turn on the +48V switch located on the front panel of the AI8 input unit. If this switch is off, no phan- tom power will be supplied to the cards installed in that unit.
Page 97: Sending A Signal From An Input Channel To A Stereo Bus
CS1D Operating Manual (Basic Operation) Sending a signal from an input channel to a STEREO bus Here’s how to use the INPUT block/ST IN block to send an input channel signal to a STEREO bus. Hint The procedure described here uses the example of an input channel, but virtually the same procedure applies to ST IN channels as well.
Page 98: Sending A Signal From An Input Channel To A Mix Bus
Chapter 4. Basic operation for input channels Sending a signal from an input channel to a MIX bus Here’s how to use the INPUT block/ST IN block to send an input channel signal to a MIX bus. Hint If the send destination is a MIX bus, the type of MIX bus (FIX or VARI) that you wish to use must ﬁrst be selected in the display.
Page 99 CS1D Operating Manual (Basic Operation) 2. Use the on-screen FIX/VARI buttons to select either FIX type or VARI type for adjacent odd-numbered even-numbered MIX buses. When you switch between FIX type and VARI type, the screen and signal ﬂow will change as follows.
Page 100 [PAN] encoder of the input channel be reﬂected for the MIX bus as well. For details refer to “CS1D Reference Manual (Software).” 5. In the INPUT block MIX SEND section, use the [ / DEC]/[ /INC] switches to select a MIX bus that you set to the VARI type.
Page 101 It is also possible to temporarily exchange the func- tions of the [MIX] encoders and faders of the input channel/ST IN channels, so that you can use the fad- ers to set the send levels. For details refer to “CS1D Reference Manual (Software).”...
Page 102: Pairing Settings
[SEL] switch will cause the state of CH 1 to be copied to CH 2. For details on the parameters that are cop- ied/linked when paired, refer to “CS1D Reference Manual (Appendices)” ( p.45). If you wish to reset the parameters, do so from the screen.
Page 103: Basic Operation In The Selected Input Channel Block
CS1D Operating Manual (Basic Operation) Basic operation in the SELECTED INPUT CHANNEL block Here we will explain how to control an input channel using the SELECTED INPUT CHANNEL block. The SELECTED INPUT CHANNEL block controls only the currently selected channel. In exchange for being limited to only one chan- nel, you can manually control virtually all of the mix parameters for the input channel, from head amp settings to EQ/ compressor/gate settings, and sends to the STEREO bus and MIX buses.
Page 104 Chapter 4. Basic operation for input channels PAIR PAIR EQ ON EQUALIZER PAIR STEREO section Switch the signal sent from the currently selected channel to the STEREO STEREO bus on/off PAIR and adjust its panning. ATTENUATOR GAIN section Attenuate the level of Adjust the input sensitivity the pre-EQ signal.
Page 105: Head Amp Settings
You can also use the CHANNEL SELECT [ /DEC]/ [ /INC] switches of the SELECTED INPUT [SEL] switch CHANNEL block to select the channel. For details GATE refer to “CS1D Reference Manual (Hardware)” ( p.34). ST IN block CLIP 2. In the SELECTED INPUT CHANNEL block, use the +48/ø/INSERT section to switch the phase and...
Page 106: Sending Signals From An Input Channel To The Stereo Bus
Chapter 4. Basic operation for input channels 4. While watching the level meter in the fader section These operations cannot be performed in the of the SELECTED INPUT CHANNEL block, use the SELECTED INPUT CHANNEL block. GAIN section [GAIN] encoder to adjust the input The PAD will be internally switched on or off when sensitivity of the channel.
Page 107 CS1D Operating Manual (Basic Operation) 6. In the STEREO OUTPUT block, turn on the STE- REO A [ON] or STEREO B [ON] switch. STEREO OUTPUT block STEREO A STEREO B [ON] switch [ON] switch TO MTRX MONO MUTE MUTE SAFE...
Page 108: Sending Signals From An Input Channel To A Mix Bus
Chapter 4. Basic operation for input channels Sending signals from an input channel to a MIX bus Here’s how to use the SELECTED INPUT CHANNEL block to send an input channel signal to a MIX bus. By using the SELECTED INPUT CHANNEL block, you can simultaneously control the signals that are sent from a spe- ciﬁc input channel to multiple MIX buses.
Page 109 CS1D Operating Manual (Basic Operation) 5. Use the MIX SEND section [PRE] switches to select MIX SEND [PAN] encoder the location (PRE/POST) from which the signal Adjusts the pan of the signal sent to the two MIX buses will be sent to VARI type MIX buses.
Page 110: Using The Delay
Chapter 4. Basic operation for input channels Using the delay By using the DELAY section of the SELECTED INPUT CHANNEL block, you can delay the input signal of an input channel by a speciﬁed interval. For example, this is useful when you wish to compensate for time differences between mic placed at a distance from each other.
Page 111: Using The Compressor
COMPRESSOR [WIDTH (dB)/KNEE] independently (link=off). (The LED will light encoder and [VALUE] indicator if link is on.) For details refer to “CS1D Ref- If the compressor type is COMP or erence Manual (Hardware)” p.26. EXPANDER...
Page 112 In the COMP PRM screen, you can also select the key-in signal (the reference signal that operates the compressor), and select either LPF or HPF as the ﬁl- ter that processes the input signal of the compressor. For details refer to “CS1D Reference Manual (Soft- ware)” ( p.142).
Page 113 RELEASE, THRESHOLD LEVEL, and GAIN. Hint For details on the parameters of each type, refer to “CS1D Reference Manual (Appendices)” ( p.11). You can also make settings so that the relevant screen appears when you operate the COMPRESSOR sec- tion. This setting is made in the UTILITY function PREFERENCE screen (“CS1D Reference Manual...
Page 114: Using The Noise Gate
(link=off). NOISE GATE [THR] encoder and LEDs (The LED will light if link is on.) For This sets the THRESHOLD LEVEL parameter details refer to “CS1D Reference Manual NOISE GATE of the internal noise gate. The approximate (Hardware)”.
Page 115 CS1D Operating Manual (Basic Operation) [Procedure] 1. Use the INPUT block [SEL] switches or the ST IN INPUT GATE LIBRARY popup window block [L]/[R] switches to select the input channel Library list that you wish to control. This shows a list of the input noise gate data that has been stored in memory.
Page 116: Using The 4 Band Eq/Hpf
Chapter 4. Basic operation for input channels Hint For details on the parameters of each type, refer to “CS1D Reference Manual (Appendices)” ( p.16). You can also make settings so that the relevant screen appears when you operate the NOISE GATE section.
Page 117 You can also make settings so that the relevant screen appears when you operate the EQUALIZER section. This setting is made in the UTILITY function PREF- ERENCE screen (“CS1D Reference Manual (Soft- ware)” p.37). As with the compressor and noise gate, EQ settings can also be stored in or recalled from a dedicated EQ library.
Page 118: Chapter 5. Basic Operation For Output Channels
EQ and compressor, and is sent from the output jack that is patched by the OUT PATCH function. The following blocks of the CS1D console are used to control output channels. MIX OUTPUT block STEREO OUTPUT block This block speciﬁes the level and on/off setting of the...
Page 119: Switching The Channel Assignments
CS1D Operating Manual (Basic Operation) Switching the channel assignments When the PM1D system is in its initial state, MIX chan- Similarly, MATRIX channels 1–12 are assigned to the nels 1–24 are assigned to the MIX OUTPUT block. MATRIX block when the PM1D system is in its initial...
Page 120: Basic Operation Of The Mix Output Block
Chapter 5. Basic operation for output channels Basic operation of the MIX OUTPUT block This section explains basic operation of the MIX OUTPUT block. Controls and functions of the MIX OUTPUT block MIX [NAME] indicator This shows the short name of the MIX channel. MIX [TO MTRX] switch and LED This is an on/off switch for the signal that is sent from the MIX channel to the MATRIX...
Page 121: Sending A Signal From A Mix Channel To An Output Unit
CS1D Operating Manual (Basic Operation) Sending a signal from a MIX channel to an output unit Here’s how the signal sent from an input channel to the MIX bus can be output from the output unit patched to the cor- responding MIX channel.
Page 122: Sending A Signal From A Mix Channel To A Matrix Bus
Chapter 5. Basic operation for output channels Sending a signal from a MIX channel to a MATRIX bus Here’s how the signal sent from an input channel to a MIX bus can be output to a MATRIX bus. [Procedure] 1. Make sure that an appropriate signal is being sent Detail of MATRIX/ST ROUTING from an input channel to a MIX bus.
Page 123 CS1D Operating Manual (Basic Operation) 5. In the screen, drag the knob located at the intersec- 7. In the MATRIX OUTPUT block, turn on the tion of the source MIX channel and the destination MATRIX [ON] switch for the appropriate MATRIX MATRIX bus to adjust the level of the signal sent channel.
Page 124: Sending A Signal From A Mix Channel To The Stereo Bus
Chapter 5. Basic operation for output channels Sending a signal from a MIX channel to the STEREO bus Here’s how the signal sent from an input channel to a MIX bus can be output to the STEREO bus. [Procedure] 1. Make sure that an appropriate signal is being sent Hint from an input channel to the corresponding MIX bus.
Page 125: Pairing Mix Channels
If you wish to reset the parameters, do so from the screen. MIX1 (VARI) LEVEL When MIX channels are paired, the functions of the controllers on the CS1D console and the parameters in the display will change as follows. MIX2 (VARI) SELECTED INPUT CHANNEL block LEVEL...
Page 126 Chapter 5. Basic operation for output channels MIX OUTPUT block If MIX channels are paired, the left (odd-numbered) encoder will function as a [BAL] encoder to set the volume bal- ance between the two MIX channels, and the right (even-numbered) encoder will function as a [LEVEL] encoder for both MIX channels.
Page 127 CS1D Operating Manual (Basic Operation) CH to MIX screen MATRIX/ST ROUTING screen In the row of paired MIX buses, the PRE buttons and The two adjacent odd-numbered even-numbered ON/OFF buttons will be consolidated for odd knobs of the source MIX channels will be linked.
Page 128: Basic Operation Of The Matrix Output Block
Chapter 5. Basic operation for output channels Basic operation of the MATRIX OUTPUT block This section explains basic operation of the MATRIX OUTPUT block. Controls and functions of the MATRIX OUTPUT block MATRIX [NAME] indicator This displays the short name of the MATRIX SAFE [RCL] LED channel.
Page 129: Pairing Matrix Channels
OUTPUT LEVEL When MATRIX channels are paired, the functions of MATRIX 1 the controllers on the CS1D console and the parame- ters in the display will change as follows. MATRIX OUTPUT block OUTPUT LEVEL If MATRIX channels are paired, the left (odd-num-...
Page 130 Chapter 5. Basic operation for output channels When MATRIX channels are paired When MATRIX buses are paired PAN knob LEVEL knob MATRIX MATRIX channel 2 channels 1/2 OUTPUT BALANCE LEVEL PAIR MIX channel 1 MIX channel 2 MATRIX buses 1/2 MATRIX buses 1/2 MIX channel 1 MIX channel 2...
Page 131: Basic Operation Of The Stereo Output Block
CS1D Operating Manual (Basic Operation) Basic operation of the STEREO OUTPUT block This section explains basic operation of the STEREO OUTPUT block. Controls and functions of the STEREO OUTPUT block STEREO [ON] switch and LED This switch turns each STEREO A/B channel on/off individually. If this switch...
Page 132: Sending A Signal From A Stereo A/B Channel To An Output Unit
Chapter 5. Basic operation for output channels Sending a signal from a STEREO A/B channel to an output unit Here’s how a signal sent from an input channel or MIX channel to the STEREO bus can be output from an output unit patched to a STEREO A/B channel.
Page 133: Basic Operation Of The Selected Output Channel Block
CS1D Operating Manual (Basic Operation) Basic operation of the SELECTED OUTPUT CHANNEL block This section explains how to use the SELECTED OUTPUT CHANNEL block to control an output channel. In the SELECTED OUTPUT CHANNEL block, you can select one channel from the MIX channels, MATRIX channels, or L/R of the STEREO A/B channels, and use the EQ and compressor to process the signal before outputting it to an output unit or to another bus.
Page 134: Sending A Signal From An Output Channel To An Output Unit
Chapter 5. Basic operation for output channels EQUALIZER DCA section Assign the currently selected channel to the desired DCA group. OUTPUT section Control the output level and on/off status of the signal sent from the cur- rently selected channel to the output SAFE section unit or STEREO bus/MATRIX bus.
Page 135 NEL SELECT [ /DEC]/[ /INC] switches. For TO MTRX MONO [SEL] switch details refer to “CS1D Reference Manual (Hard- ware)” ( p.66). By repeatedly pressing a [SEL] switch of the STEREO OUTPUT block, you can alternate between the L channel and the R channel.
Page 136: Sending A Signal From A Mix Channel To A Matrix Bus/Stereo Bus
Chapter 5. Basic operation for output channels Sending a signal from a MIX channel to a MATRIX bus/STEREO bus Here’s how you can use the SELECTED OUTPUT CHANNEL block to send a MIX channel signal to the STEREO bus or a MATRIX bus.
Page 137 CS1D Operating Manual (Basic Operation) 8. If you are sending the MIX channel signal to the STEREO bus, use the [PAN/BAL] encoder located in the OUTPUT section to adjust the pan. If a MIX channel is selected in the SELECTED OUT-...
Page 138: Sending A Signal From The Stereo A Channel To The Matrix Bus
Chapter 5. Basic operation for output channels Sending a signal from the STEREO A channel to the MATRIX bus Here’s how to use the SELECTED OUTPUT CHANNEL block to send the signal of the STEREO A channel to a MATRIX bus.
Page 139: Delay Settings
CS1D Operating Manual (Basic Operation) Delay settings You can use the DELAY section of the SELECTED OUTPUT CHANNEL block to delay the output signal of a desired output channel by a ﬁxed time. For example, this provides a convenient way to compensate between speaker systems that are located at a distance from each other.
Page 140: Compressor Settings
[VALUE] encoder independent key-in signals (link=off). (The LED will light when link is on.) When the compressor type is For details refer to “CS1D Reference COMP or EXPANDER Manual (Hardware)” ( p.61). use the [TIME] encoder to set the KNEE parameter of the COMP or COMPRESSOR [GR] meter LEDs EXPANDER.
Page 141 The COMP PRM screen also lets you select the key- in signal (the reference signal that controls the com- pressor), and to switch between LPF and HPF to ﬁl- ter the input signal of the compressor. For details refer to “CS1D Reference Manual (Software)” ( p.93).
Page 142: Band Eq/Hpf Settings
OUTPUT CHANNEL block, turn on the COM- For details on the parameters of each type, refer to PRESSOR [ON] switch. “CS1D Reference Manual (Appendices)” ( p.11). The compressor of the corresponding channel will be You can make settings so that the corresponding enabled.
Page 143 CS1D Operating Manual (Basic Operation) [Procedure] 1. Press a [SEL] switch in the MIX OUTPUT block, MATRIX OUTPUT block, or STEREO OUTPUT block to select the output channel that you wish to control. 2. In the EQUALIZER section of the SELECTED OUT- PUT CHANNEL block, turn on the [EQ ON] switch.
Page 144: Chapter 6. Insert And Direct Out
Chapter 6. Insert and direct out This chapter explains how external devices such as effect processors can be inserted into a speciﬁc channel, and how the signal of an input channel can be directly output from a desired output jack. Insert An external device such as an effect processor can be inserted in an input channel/output channel of the PM1D system.
Page 145: Inserting Into An Input Channel
CS1D Operating Manual (Basic Operation) Inserting into an input channel Here’s how an external device connected to an input/output unit can be inserted into an input channel. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the INSERT PATCH screen (IN PATCH function)
Page 146 Chapter 6. Insert and direct out 4. In the LCD FUNCTION ACCESS block, press the INSERT/DIRECT OUT screen (IN PATCH func- INPUT [PATCH] switch several times to access the tion) following INSERT/DIRECT OUT screen (IN PATCH function). In the INSERT/DIRECT OUT screen (IN PATCH function) you can switch insertion on/off for each input channel.
Page 147 CS1D Operating Manual (Basic Operation) 8. From the 1-24 INS, 25-48 INS, 49-72 INS, 73-96 1 GAIN GANG INS, and ST IN INS tabs, click the tab that contains If this button is on, the head amp gain settings of...
Page 148: Inserting Into An Output Channel
Chapter 6. Insert and direct out Inserting into an output channel Here’s how an external device can be inserted into an output channel (MIX channel, MATRIX channel, STEREO A/B channel). Most of the steps are the same as for an input channel. [Procedure] 1.
Page 149 CS1D Operating Manual (Basic Operation) 7. In the LCD FUNCTION ACCESS block, press the For a digital I/O card (MY card) installed in the DIO8 OUTPUT [INSERT] switch. The OUT INSERT function screen will appear. This contains mainly preamp settings for the input card that is patched to the insert point.
Page 150: Direct Out
Chapter 6. Insert and direct out Direct out An input source patched to an input channel can be output directly from a desired output jack without being affected by the STEREO bus or MIX buses. Direct out connections If you wish to directly output a speciﬁc signal, you can use an output jack of an output unit as a direct output. Direct out connection example 1 Direct out connection example 2 OUTPUT UNIT NO.
Page 151 CS1D Operating Manual (Basic Operation) From the top, this shows the type and number of the output unit, the slot number of the Number of the input card, and the channel number channel of the output jack. To patch the direct out point of a channel to the desired Name of the input channel output jack, click this grid to display a “...
Page 152: Chapter 7. Dca Groups/Mute Groups
Chapter 7. DCA groups/Mute groups On the PM1D system, channels can be assigned to a DCA group/mute group to adjust the levels or switch muting on/off for a group of channels. This chapter explains operations for DCA groups and mute groups. DCA groups The PM1D system has 12 DCA groups to which input channels (input channels, ST IN channels) or output channels (MIX channels) can be assigned.
Page 153 CS1D Operating Manual (Basic Operation) Hint INPUT block INPUT block The assignment of input channels/output channels to DCA groups can also be performed within the dis- play (IN DCA/MUTE function DCA ASSIGN screen, OUT DCA/MUTE function DCA ASSIGN screen). You can also use the SELECTED INPUT CHANNEL block (or the SELECTED OUTPUT CHANNEL block) to assign the desired channel to a DCA group.
Page 154: Controlling A Dca Group
Chapter 7. DCA groups/Mute groups Controlling a DCA group By using the DCA faders in the DCA GROUP block of the console, you can control the levels of each DCA group. [Procedure] 1. Assign input channels/output channels to a DCA 4.
Page 155: Mute Groups
CS1D Operating Manual (Basic Operation) Mute groups The PM1D system provides 12 mute groups, to which the desired input channels (input channels, ST IN channels) or output channels (MIX channels, MATRIX channels) can be assigned. By using the [1]–[12] switches located in the SCENE MEMORY block of the console, you can turning muting on/off for each mute group.
Page 156: Assigning Output Channels To A Mute Group
Chapter 7. DCA groups/Mute groups Assigning output channels to a mute group Here’s how to assign an output channel (MIX channel, MATRIX channel) to a mute group. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the 3. In the same way, assign output channels to other OUTPUT [DCA/MUTE] switch several times to mute groups.
Page 157: Controlling A Mute Group
CS1D Operating Manual (Basic Operation) Controlling a mute group By using the SCENE MEMORY [1]–[12] switches in the SCENE MEMORY block of the console, you can switch muting on/off for mute groups 1–12. [Procedure] 1. Assign input channels/output channels to mute groups 1–12.
Page 158 Chapter 7. DCA groups/Mute groups 4. Press a SCENE MEMORY [1]–[12] switch. The LED of the corresponding switch will light, and the mute group assigned to that switch will be muted. (All channels assigned to that group will be in the same state as if their [ON] switches had been turned off.) Hint You can turn on multiple buttons to simultaneously...
Page 159: Chapter 8. Scene Memory
( p.166). About scenes The scenes of the PM1D system contain settings for all the controllers of the CS1D (except for display contrast and ana- log volume settings), as well as the settings for the following functions in the display.
Page 160 Chapter 8. Scene memory The currently selected scene is shown by the [SCENE Using the SCENE MEMORY [0]–[9] switches to NUMBER] indicator located in the SCENE MEMORY directly input the scene number block of the console. In this method, you use a three-digit number to specify the scene number.
Page 161: Scene Memory Operations
RECALL STORE SCENE NUMBER SCENE MEMORY block MUTE [Procedure] 1. Use the panel controllers of the CS1D to set the mix parameters. 2. Use the SCENE MEMORY [0]–[9] switches or the RECALL PREVIEW UNDO SCENE MEMORY [ /DEC]/[ /INC] switches to...
Page 162: Recalling A Scene
Chapter 8. Scene memory If there are any changes in a UNIT, PATCH, or You must ﬁrst switch the EVENT RECALLING but- NAME library that is linked to that scene, the popup ton to “DISABLE.” window for the corresponding library will appear While a message asking you to conﬁrm the Store after the SCENE STORE popup window.
Page 163: Using Preview Mode
Only the setting values of the scene selected in step 2 will be loaded, and shown in the LEDs and display of the CS1D panel. However, the internal signal pro- cessing of the system will remain as it was prior to the recall operation, and will not change.
Page 164: Directly Recalling A Scene
Chapter 8. Scene memory Directly recalling a scene Frequently-used scenes can be assigned to the SCENE MEMORY [1]–[12] switches of the SCENE MEMORY block, and directly recalled at one touch. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the 4.
Page 165: Chapter 9. Recall Safe/Mute Safe
Chapter 9. Recall safe/Mute safe This chapter explains the “Recall Safe” function that excludes speciﬁc channels or parameters from recall operations, and the “Mute Safe” screen that excludes speciﬁc channels from mute operations. Recall safe “Recall Safe” is a function that allows you to specify certain channels or parameters to remain unaffected when a scene is recalled.
Page 166: Using The Screen To Set/Defeat Recall Safe
Chapter 9. Recall safe/Mute safe If Recall Safe is speciﬁed for either (not both) the channels are paired, pairing will be forcibly odd-numbered or even-numbered channel of two defeated, and the channel that was set to Recall Safe channels, and you recall a scene in which these two will maintain the state prior to the recall.
Page 167: Mute Safe
CS1D Operating Manual (Basic Operation) In the case of parameters of which there is only one 3. To defeat Recall Safe, turn off the button of the cor- setting for two adjacent odd-numbered even- responding channel/parameter in the RECALL numbered channels (such as the parameters listed SAFE screen.
Page 168: Using The Screen To Set/Defeat Mute Safe
Chapter 9. Recall safe/Mute safe Using the screen to set/defeat Mute Safe You can also set/defeat Mute Safe from within the display. This method is convenient when you wish to quickly make set- tings for multiple channels. [Procedure] 1. To set Mute Safe for input channels, press the 3.
Page 169: Chapter 10. Monitor
The PM1D system provides two monitor outputs, MONITOR A and MONITOR B. For each, the monitoring source can be selected and the output level set independently. To control MONITOR A/MONITOR B from the CS1D console, you will use the following sections of the MASTER block.
Page 170: Controls And Functions Of The Monitor A/Monitor B Sections
MONITOR A headphone jack nel, output channel, or DCA group is on, and the located on the top panel or front panel of the CS1D. cue signal will be output from MONITOR OUT jacks A. The CUE ACTIVE LED (located in the...
Page 171 MONITOR A screen. MONITOR A output when that signal exceeds a cer- tain level. For details refer to “CS1D Reference Man- ual (Software)”. 4. In the MASTER block MONITOR A section, press...
Page 172: Using The Monitor B Section To Monitor A Signal
CS1D. Do not use the top panel PHONES MONITOR jack simultaneously with the front panel MONITOR headphone jack. Doing so may cause the CS1D to malfunction due to excessive current. 2. In the LCD FUNCTION ACCESS block, press the [MON/CUE] switch several times to access the fol- lowing MONITOR B screen.
Page 173 Hint In the MONITOR B screen you can also use DIRECT IN to directly monitor the signal from a speciﬁc input jack. For details refer to “CS1D Reference Man- ual (Software)”. 4. In the MASTER block MONITOR B section, press...
Page 174: Using The Cue/Solo Function
Cue mode and Solo mode The input channels, output channels, and DCA groups of the CS1D each provide a [CUE] switch that is used by the Cue/ Solo function. The result of pressing the [CUE] switch will depend on whether CUE mode or SOLO mode is selected.
Page 175: Cue/Solo Groups
DCA GROUP block [CUE] switch ority, and the cue/solo signals of that group will be enabled. For details on cue operation, refer to “CS1D Refer- ence Manual (Hardware)” ( p.81). Hint For details on DCA groups, refer to “Chapter 7. DCA...
Page 176: Controls And Functions Of The Cue Section
Chapter 10. Monitor Controls and functions of the CUE section Operations for the Cue/Solo function are performed in the CUE section of the MASTER block or in the display (MON/ CUE function CUE/SOLO screen). The controls and functions of the CUE section are explained below. [INPUT AFL] switch and LED This switch selects the output location of the signal that is sent to the CUE bus when a [CUE] switch of an input...
Page 177 CS1D Operating Manual (Basic Operation) 3. Use the [INPUT AFL] switch located in the CUE 7. Make sure that the [SOLO] switch of the CUE sec- section of the MASTER block to specify the posi- tion is off (Cue mode).
Page 178: Using The Solo Function
Chapter 10. Monitor Using the Solo function Here’s how to use the Solo function of the PM1D. [Procedure] 1. Use the [LAST CUE] switch of the CUE section to 4. In the SOLO SAFE section of the CUE/SOLO select either LAST CUE mode ([LAST CUE] switch screen, select the channel(s) that you wish to on) or MIX CUE mode ([LAST CUE] switch off) as exclude from the Solo operation.
Page 179: Talkback
The CS1D console has input jacks for two talkback mics: a TALKBACK 1 jack (top panel) and a TALKBACK 2 jack (rear panel). The talkback signals that are input from these two jacks are mixed inside the CS1D and can be sent to the desired bus or output jack.
Page 180 If necessary, you can also output the talkback signal directly from a desired output jack. For details refer to “CS1D Reference Manual (Software)”. 4. In the TALKBACK section of the MASTER block, press the [TB ON] switch.
Page 181: Oscillator
CS1D Operating Manual (Basic Operation) Oscillator The PM1D provides an internal oscillator for test purposes, and can send a sine wave or pink noise to the desired bus. This can be used to check the operation of devices connected to an output unit, or to check the acoustical characteristics of a concert location.
Page 182 Hint If necessary, you can also output the oscillator signal directly from the desired output jack. For details refer to “CS1D Reference Manual (Software)”. 6. Press the [OSC ON] switch in the OSCILLATOR section of the MASTER block. MASTER block...
Page 183: Chapter 12. Internal Effects
Chapter 12. Internal effects This chapter explains how to use the internal effects. About the internal effects of the PM1D system The PM1D system contains eight effect units. For each effect unit, you can select one of 29 effect types. The inputs and outputs of these internal effects are not ﬁxed to any particular bus or channel.
Page 184: Patching An Internal Effect
Chapter 12. Internal effects Patching an internal effect To use an internal effect, you must ﬁrst patch the input and output of the effect to an appropriate signal path. Here we will explain two typical methods of patching. Using an internal effect via the MIX bus Here’s how you can patch MIX channel outputs to the effect input, and the effect outputs to input channels.
Page 185 CS1D Operating Manual (Basic Operation) The EFFECT function has eight screens for the eight 5. From the buttons in the top row of the screen, click effects EFFECT 1 – EFFECT 8, allowing settings to be the MIX button, and then click the number of the made independently.
Page 186 Chapter 12. Internal effects 7. In the row of buttons at the top of the screen, click Hint either the IN 1-48 button or the IN 49-96 button If the MIX channels are paired, the left (odd-num- {on the 48 channel mode, this button has no effect}, bered) encoder will function as a MIX [BAL] and then click the button for the channel that you encoder to adjust the volume balance between the...
Page 187: Inserting An Internal Effect Into A Channel
CS1D Operating Manual (Basic Operation) Inserting an internal effect into a channel With this method, an internal effect can be patched between the insert out and insert in of a desired channel. As an example, we will explain how to insert an effect into an input channel.
Page 188 Chapter 12. Internal effects For channels that are already used by another chan- 10. Turn on the [ON] switch of the input channel (or nel, the NAME will be displayed in white characters ST IN channel) into which the effect was inserted, on a red background.
Page 189: Basic Operation Of The Effect Screen
CS1D Operating Manual (Basic Operation) Basic operation of the effect screen This section explains how you can use the EF function screen to edit effect parameters, and recall/store effect library data. Editing effect parameters In the EFFECT function screen, you can use the knobs or buttons to edit effect parameters.
Page 190: Recalling Effect Data From The Library
Chapter 12. Internal effects CS1D MIX OUTPUT block Hint • When the EFFECT 1–EFFECT 8 screens are dis- played, you can obtain the same result by holding down the [SHIFT/GRAB] switch located in the PAIR PAIR PAIR PAIR PAIR PAIR data entry block and pressing the MIX LAYER [1- 24] switch or [25-48] switch.
Page 191 CS1D Operating Manual (Basic Operation) 2. Click the EFFECT LIBRARY button located in the upper right of the screen. The EFFECT LIBRARY popup window will appear, in which you can recall/store effect data from/to the effect library. EFFECT LIBRARY button...
Page 192: Storing Effect Data To The Library
Chapter 12. Internal effects Storing effect data to the library You can store (save) effect parameter settings in the effect library for later re-use. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the LIBRARY STORE popup window [EFFECT] switch several times to select the desired screen from EFFECT 1 –...
Page 193: Chapter 13. Graphic Eq
Chapter 13. Graphic EQ The PM1D system provides twenty-four 31-band graphic EQ modules. This chapter explains how to operate the graphic Inserting a graphic EQ into a channel The 24 GEQ (graphic EQ) modules built into the PM1D system can be patched to the insert-out/insert-in of a desired channel.
Page 194 Chapter 13. Graphic EQ The following signal routes can be selected as a patch 6. Turn on the GEQ ON/OFF button located in the destination. upper middle of the screen. IN 1-48 INSERT OUT Hint Patch to the insert-out/insert-in of an input chan- The GEQ can also be switched on/off in the GEQ nel 1–48 or ST IN channel 1–4.
Page 195: Controlling A Graphic Eq
CS1D Operating Manual (Basic Operation) Controlling a graphic EQ To control a graphic EQ, you can either use the virtual faders and virtual knobs shown in the display, or the DCA faders of the CS1D console. Controlling a graphic EQ from the display Here’s how to control the desired GEQ module by using the virtual faders and virtual knobs shown in the GEQ function...
Page 196: Controlling A Graphic Eq From The Dca Faders
Chapter 13. Graphic EQ on/off, the Q knobs adjust the steepness, and the F Hint knobs adjust the center frequency. Notch ﬁlters 1–4 are independent of the graphic EQ, Notch ﬁlters and are not affected by the GEQ ON/OFF button. If necessary, you can access the graphic EQ module and use only the notch ﬁlters.
Page 197 GROUP block will return to their previous state. following diagram. At this time, the [FADER STATUS] switches in the DCA GROUP block of the CS1D will function as graphic EQ band select switches, as shown in the fol- lowing diagram.
Page 198: Chapter 14. Midi/Time Code
MIDI IN MIDI OUT MIDI IN External device (MIDI sequencer, etc.) Console (CS1D) 2. In the LCD FUNCTION ACCESS block, press the MIDI PROGRAM screen (MIDI/GPI/TC function) [MIDI/GPI/TC] switch several times to access the following MIDI PROGRAM screen. LCD FUNCTION ACCESS...
Page 199 In this case, the number displayed in the CH MIDI channel/program number. When the corre- column of the PROGRAM CHANGE EVENT list sponding events are executed on the CS1D, a pro- will be the bank number. gram change 1–128 will be transmitted to the external device on a MIDI channel 1–16.
Page 200 MIDI channel. The event assigned to that program number will be executed. When you execute one of the assigned events on the CS1D, a program change (or bank select + program change) will be transmitted to the external device.
Page 201: Using Time Code To Control Events
CS1D Operating Manual (Basic Operation) Using time code to control events On the PM1D system, speciﬁed scenes can be recalled when the LTC time code received at the TIME CODE IN connec- tor (or the time code internally generated by the PM1D system itself) reaches a speciﬁed time location. Here we will explain how to capture a time code time location, and how to assign the desired scene to that time location.
Page 202 Chapter 14. MIDI/Time Code The following sources can be selected. 7. When you come to the moment at which you want a scene to be recalled, click the CAPTURE button in CONSOLE ..Time code (LTC) will be received the TC EVENT screen. from the TIMECODE IN con- Each time you click the CAPTURE button, the time nector of the console.
Page 203: Chapter 15. Using A Memory Card To Save/Load Data
[PC] card slot A or B located on the top panel of the [UTILITY] switch several times to access the fol- CS1D. lowing LOAD/SAVE screen. Cards may be inserted or removed while the power of the CS1D is turned on. LCD FUNCTION ACCESS block MASTER block [UTILITY] switch...
Page 204 Chapter 15. Using a memory card to save/load data LOAD/SAVE screen (UTILITY function) 5. If you selected Scene Memory in step 4, use the on- screen From No. knob and To No. knob to specify the desired number(s). (Alternatively, you can select “ALL.”) For example if you select Scene Memory in the SAV- ING MEMORY SELECT section and set the From...
Page 205: Loading A File From A Memory Card
CS1D Operating Manual (Basic Operation) Loading a ﬁle from a memory card Here’s how to load the desired data from a memory card into the PM1D system. [Procedure] 1. Insert the PC ﬂash storage card containing the data LOAD/SAVE screen (UTILITY function) into [PC] card slot A or B located on the top panel of the CS1D.
Page 206 Chapter 15. Using a memory card to save/load data Never insert or remove a memory card while the card is being accessed. If the EVENT RECALLING button is set to “ENABLE” in the MIDI/GPI/TC function TC EVENT screen, the LOAD button will be grayed, and loading will not be possible.
Page 207: Chapter 16. Various Settings
This chapter explains various settings that allow you to customize the PM1D system. Initial settings for the console Here’s how to make initial settings that affect the basic operation of the CS1D console, such as track pad/mouse opera- tion and operation within the display.
Page 208 DELAY button Delay-related con- IN DELAY / OUT trollers DELAY ing data to a memory card inserted in the PC ATA STORAGE CARD slot of the CS1D, the settings of ROUTING button Routing-related PAN/ROUTING / controllers MATRIX/ST or the PREFERENCE screen will be saved on the card as OUT CH VIEW well.
Page 209: Setting The Internal Calendar And Clock
CS1D Operating Manual (Basic Operation) Setting the internal calendar and clock Here’s how to set the date of the internal calendar and the time of the internal clock. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the 2. Use the six knobs of the INTERNAL CALENDAR/ [UTILITY] switch several times to access the fol- CLOCK section to set the date and time.
Page 210: Specifying The Metering Points
Chapter 16. Various settings Specifying the metering points The metering point (the location at which the level is detected) for the level meters on the CS1D console can be speciﬁed independently for input channels and output channels. Input channel metering point Here’s how to set the metering point for the input levels displayed by the level meters of the INPUT block/ST IN block.
Page 211: Output Channel Metering Point
[METER] switch Hint You can also use the METER [PEAK HOLD] switch in the METER section (MASTER block) of the CS1D to turn peak hold on/off for the output channels. MATRIX 1-24/ST/MONITOR screen (METER function) The MIX 1-48 screen and MATRIX 1-24/ST/MONI-...
Page 212: User Defined Function Settings
Chapter 16. Various settings User deﬁned function settings You can assign the desired function to the USER DEFINE [1]–[8] switches in the USER DEFINE block of the CS1D con- sole, and use them to control the system. [Procedure] 1. In the LCD FUNCTION ACCESS block, press the...
Page 213 CS1D Operating Manual (Basic Operation) BOOKMARK (parameters: none) Access the last-registered screen. The LED will light for a USER DEFINE switch to which this function is assigned if a screen has been assigned. When the functions of the USER DEFINE [1]–[8] switches are...
Page 214 Reference Manual...
Page 215 Reference Manual (Hardware)
Page 216 Contents How the “CS1D Reference Manual (Hardware)” is organized ....1 Printing conventions in the “CS1D Reference Manual (Hardware)” ............3 INPUT block .
Page 217 Contents MASTER block........... . . 77 TALKBACK section.
Page 218: How The "Cs1D Reference Manual (Hardware)" Is Organized
How the “CS1D Reference Manual (Hardware)” is organized How the “CS1D Reference Manual (Hardware)” is organized The “CS1D Reference Manual (Hardware)” explains the function and operation of each block of the CS1D control sur- face. CS1D Top panel SELECTED OUTPUT CHANNEL block ( p.56) MATRIX OUTPUT block ( p.46)
Page 219 “CS1D Operating Manual (Basic Opera- tion).” For details on the functions and operations within the display of the CS1D, refer to “CS1D Reference Manual (Software).” Screen shots shown in this manual are taken from a prototype. Please be aware that they may differ...
Page 220: Printing Conventions In The "Cs1D Reference Manual
Printing conventions in the “CS1D Reference Manual (Hard- ware)” In general, the “CS1D Reference Manual (Hardware)” is written for the 96 channel model of the PM1D system (the model that uses the DSP1D-EX for its engine). If speciﬁcations differ between the 96 channel model and the 48 channel model (the model that uses the DSP1D for its engine), the speciﬁcations of the 48...
Page 221: Input Block
CS1D Reference Manual (Hardware) INPUT block [Function] This block speciﬁes the pan and level of the signals patched to monaural input channels 1–96 {1–48}, and sends them to the STEREO bus or MIX buses 1–48 or assigns them to the DCA groups.
Page 222: Input Block Channel Assignments
INPUT block channel assignments The top panel of the CS1D has four blocks located at top, bottom, left and right. When the PM1D system is in the default state, channels 1–12, 13–24, 25–36, and 37–48 are assigned to these blocks in the...
Page 223 48.) FADER …… When the CS1D is in its default state, changing the MIX bus that is the object of operations in one INPUT block will also cause the MIX bus selected for the other INPUT blocks to be switched in tan- MIX1 (ODD) dem.
Page 224 INPUT [PAN] encoder. For details refer to The range is from – dB – +10 dB, and the approxi- “CS1D Reference manual (Software),” CH to MIX mate current value is shown by the LEDs around the (PAN/ROUTING function).
Page 225 CS1D Reference Manual (Hardware) B INPUT [ø] (Phase) LED The adjustable range is +10 dB — –68 dB. The If settings have been made to invert the phase of the approximate current value is shown by the LEDs input signal for this input channel, this LED will around the perimeter of the encoder.
Page 226 CH 1 [SEL] switch and press the CH 2 [SEL] switch. The state of CH 1 will be copied to CH Threshold level 2. For details on the parameters that are copied/ linked for a pair, refer to “CS1D Reference Manual (Appendices)” (→p.45). Time [–]...
Page 227: Input Fader
CS1D Reference Manual (Hardware) When the FADER FLIP [CH] switch is on If a VARI type MIX bus is selected, this encoder will adjust the send level to that MIX bus. If a FIX type MIX bus is ® selected, only the LED at the...
Page 228 INPUT block M INPUT [ASSIGN DCA] switch and LEDs O SAFE [MUTE] LED This switch assigns the input channel to DCA groups This LED will light if the input channel has been set 1–12. When an input channel is assigned to a DCA to Mute Safe (a state in which the input channel is group, the corresponding LED will light.
Page 229 CS1D Reference Manual (Hardware) ST IN block [Function] This block adjusts the pan and level of the stereo signals patched to ST IN channels 1–8 {1–4}, and sends them to the STEREO bus or to MIX buses 1–48, or assigns them to DCA groups.
Page 230: St In Block
ST IN block Channel assignments for the ST IN block The ST IN block contains four modules, two above and two below. In the default state of the PM1D system the lower two modules are assigned to control ST IN channels 1/2, and the upper two modules are assigned to control ST IN channels 3/4.
Page 231 CS1D Reference Manual (Hardware) The on/off setting can be switched from the console in the SELECTED INPUT CHANNEL block, or in STATUS the display (PAN/ROUTING function CH to MIX screen/MIX ASSIGN screen). You can set the FADER [FLIP] switch in the SELECTED INPUT CHANNEL block to exchange (ﬂip) the function of the ST IN [MIX] encoder (2)
Page 232 ST IN block 7 ST IN [INS] LED CLIP This LED will light if insertion is turned on for the ST IN channel. COMP Insertion can be switched from the console in the SELECTED INPUT CHANNEL block, or in the dis- play (IN PATCH function INSERT/DIRECT POINT GATE screen).
Page 233 CS1D Reference Manual (Hardware) When the compressor type is COMPANDER Hint The noise gate on/off status and its parameters can COMPANDER be set in the SELECTED INPUT CHANNEL block, Key-in signal Level Output signal or in the display (IN GATE/COMP function GATE ATTACK PRM screen).
Page 234 ST IN block When the FADER FLIP [CH] switch is on STATUS If a VARI type MIX bus is selected, this encoder will adjust the send level to that MIX bus. If a FIX type MIX bus is selected, only the LED at the ®...
Page 235 CS1D Reference Manual (Hardware) I ST IN [DCA] switch and LEDs K SAFE [MUTE] LED This switch assigns the ST IN channel to DCA This LED will light if the ST IN channel has been set groups 1–12. to Mute Safe (a state in which the channel is unaf- fected by mute group operations).
Page 236: Selected Input Channel Block
SELECTED INPUT CHANNEL block SELECTED INPUT CHANNEL block [Function] In this block you can view and set the parameters of the currently selected input channel or ST IN channel. Hint If desired, the related screen can be made to appear automatically when this block is operated. This setting is made in the UTILITY function PREFERENCE screen.
Page 237 CS1D Reference Manual (Hardware) [Procedure] Selecting a channel The channel to be controlled by the SELECTED INPUT CHANNEL block can be selected in the following ways. 1. Use a [SEL] switch 2. Use the SELECTED INPUT CHANNEL block You can use the INPUT block INPUT [SEL] switches...
Page 238: 48/Ø/Insert (+48/Phase/Insert) Section
SELECTED INPUT CHANNEL block +48/ø/INSERT (+48/phase/insert) section In this section you can switch phantom power on/off, reverse the phase, and switch insertion on/off. +48V INSERT +48V / / INSERT 1 [+48 V] switch and LED If an AD card with head amp is patched to the chan- nel, this switch turns the phantom power on/off.
Page 239: Input Section
CS1D Reference Manual (Hardware) INPUT section In this section you can switch between input jacks A/B of the AD card with head amp (LMY2-ML). INPUT 1 INPUT [A]/[B] switches and LEDs The LED for the currently selected input jack (A/B) If an AD card with switchable input jacks A/B is will light.
Page 240: Mix Send Section
SELECTED INPUT CHANNEL block MIX SEND section In this section, the signals sent from the currently selected channel to MIX buses 1–48 can be switched on/off, and their send levels adjusted. PAIR PAIR PAIR 1 MIX SEND [PAIR] LED 2 MIX SEND [LEVEL/PAN] encoder and LEDs This LED will light to indicate two adjacent odd and This encoder sets the send level of the signal that is even-numbered MIX buses 1–48 (MIX buses 1/2, 3/...
Page 241 CS1D Reference Manual (Hardware) 3 MIX SEND [NAME] indicator Of the LEDs around the [PAN] encoder, the LED at mark indicates that the signal is panned to the This shows the short name of the MIX bus. center. The short name can be input in the display (OUT PATCH function NAME screen, etc.).
Page 242: Compressor Section
SELECTED INPUT CHANNEL block COMPRESSOR section In this section you can make settings for the internal compressor. All parameters can be controlled from the top panel, except for compressor library store/recall operations, compressor type selection, and key-in signal selection. 3 COMPRESSOR FILTER [ON] switch and LED This is an on/off switch for the HPF or LPF that is placed in the ﬁrst stage of the internal compressor.
Page 243 CS1D Reference Manual (Hardware) A COMPRESSOR [ON] switch and LED Hint This switch turns the internal compressor on/off. In the UTILITY function PREFERENCE screen you When the compressor is on, the LED will light. can specify whether the GR meter display will be linked with the compressor on/off setting.
Page 244: Noise Gate Section
SELECTED INPUT CHANNEL block NOISE GATE section In this section you can make settings for the internal noise gate. All parameters can be controlled from the top panel, except for noise gate library store/recall operations, noise gate type selection, and key-in signal selection. 4 NOISE GATE SIG [+]/[THR]/[–] LEDs These LEDs indicate the level of the noise gate key-in signal (after passing through the ﬁlters).
Page 245 CS1D Reference Manual (Hardware) The current value is shown by the [VALUE] indica- B NOISE GATE [ON] switch and LED tor. (Either the [msec] or [sec] LED will light to indi- This switch turns the internal noise gate on/off. cate the units of the displayed value.) When the noise gate is on, the switch LED will light.
Page 246: Equalizer Section
SELECTED INPUT CHANNEL block EQUALIZER section In this section you can make settings for the internal four-band EQ (HIGH, HIGH MID, LOW MID, LOW). Of the four bands, HIGH and LOW EQ can be switched between shelving and peaking, and the HIGH band can also be used as an LPF.
Page 247: Stereo Section
CS1D Reference Manual (Hardware) STEREO section In this section, the signal that is sent from the currently selected channel to the STEREO bus can be switched on/off and panned. STEREO 1 STEREO [FIXED MIX PAN] switch and LED 2 STEREO [TO ST] switch and LED...
Page 248: Gain Section
SELECTED INPUT CHANNEL block GAIN section 1 [GAIN] encoder and LEDs 2 GAIN [CLIP] LED If an AD card with head amp is patched to this chan- This LED will light if the input signal of the input nel, this encoder sets the input sensitivity of the head channel clips.
Page 249: Fader Section
CS1D Reference Manual (Hardware) FADER section In this section you can switch the currently selected channel on/off, and set its input level. 1 CLIP [EQ] LED 5 Meter LEDs This LED will light when the post-EQ signal clips. This is a twelve-point LED meter that indicates the input level of the channel.
Page 250: Dca Section
SELECTED INPUT CHANNEL block DCA section This section assigns the currently selected channel to a DCA group. It is convenient to use this section when you wish to assign a single channel to multiple DCA groups. 1 DCA [1]–[12] switches and LEDs [Procedure] These switches assign the currently selected channel Using the SELECTED INPUT CHANNEL block to...
Page 251: Safe Section
CS1D Reference Manual (Hardware) SAFE section In this section you can set or defeat Recall Safe or Mute Safe settings for the currently selected channel. RECALL MUTE SAFE 1 SAFE [RECALL] switch and LED 2 SAFE [MUTE] switch and LED...
Page 252 SELECTED INPUT CHANNEL block This function is convenient when you wish to quickly select an input channel that is at the same position of another INPUT block. 4 [CHANNEL COPY] switch and LED This switch is used to copy parameters from the desired input channel to another input channel.
Page 253: Global Control Section
The functions of the faders and [MIX] encoders will change as follows, depending on the switch that is turned on. The status of this switch will always be shown at the bottom of the display. For details refer to “CS1D Reference manual (Software).” When FADER FLIP [CH] switch is on (default)
Page 254 TOR A and MONITOR B. Do not use both the headphone jack on the top panel and the headphone jack on the front panel at the same time. Doing so can cause the CS1D to malfunction due to excessive current.
Page 255 CS1D Reference Manual (Hardware) Signal ﬂow for input channels 1–96 {1–48} from PRE ATT. CH 1(-48) to OUTPUT PATCH from PRE EQ METER (-96) INSERT OUT 1(-48) (-96) PEAK METER METER METER METER FADER INSERT ATT. 4BAND COMP DELAY GATE...
Page 256: Display
Before moving the CS1D, you must be sure to lower the display toward the back until it is fastened in position. Since the LCD display is manufactured with extremely del-...
Page 257: Mix Output Block
CS1D Reference Manual (Hardware) MIX OUTPUT block [Function] This block sets the level and on/off status of the signals sent from the input channels and ST IN channels to MIX buses 1–48, and outputs them to the output units patched to each MIX channel and to the STEREO bus and MATRIX buses.
Page 258: Channel Assignments In The Mix Output Block
MIX OUTPUT block Channel assignments in the MIX OUTPUT block The MIX channel section of the MIX OUPUT block contains a total of 24 MIX channel modules; 12 channels above and 12 channels below. In the default state of the PM1D system, these modules are assigned to control MIX channels 1–24. However in the MIX OUTPUT block MIX LAYER section, you can change this assignment as follows.
Page 259: Mix Channel Section
CS1D Reference Manual (Hardware) MIX channel section In this section you can switch the on/off status and set the output level of each MIX channel 1–48. PAIR 1 MIX [NAME] indicator 5 MIX [RCL SAFE] LED This displays the short name of the MIX channel.
Page 260 MIX OUTPUT block [Procedure] When MIX channels are not paired Assigning a MIX channel to a DCA group 1. In the DCA GROUP block, press one of the [ASSIGN DCA] switches 9–12 to select a DCA group (9–12). 2. In the MIX OUTPUT block, press the MIX [DCA] switch of the MIX channel that you wish to assign to the above-selected DCA group.
Page 261 (OUT- ied to MIX 2. For details on the parameters that are PUT PATCH function INSERT PATCH screen) will copied/linked for a pair, refer to “CS1D Reference be enabled. Manual (Appendices)” ( p.45).
Page 262: Mix Layer Section
MIX OUTPUT block MIX LAYER section In this section you can select the group of channels that will be controlled by the MIX channel section. 1-24 LAYER 1 MIX LAYER [1–24]/[25–48] switches and LEDs These switches select the channels that will be con- trolled by the MIX channel section.
Page 263: Matrix Output Block
CS1D Reference Manual (Hardware) MATRIX OUTPUT block [Function] In this block you can set the level and on/off status of the signals that are sent from MIX channels 1–48, STE- REO A, B channel, and SUB IN channels to MATRIX buses 1–24, and send them to the output unit that is patched to each MATRIX channel.
Page 264: Matrix Output Block Channel Assignments
MATRIX OUTPUT block MATRIX OUTPUT block channel assignments The MATRIX channel section of the MATRIX OUTPUT block contains 12 modules. When the PM1D system is in its default state, these modules are assigned to control MATRIX channels 1–12. However, these assignments can be changed as follows by an operation in the MATRIX LAYER section. Using the MATRIX LAYER switches to change the MATRIX channel assignments 1-12...
Page 265: Matrix Channel Section
CS1D Reference Manual (Hardware) MATRIX channel section In this section you can set the on/off status and output level of MATRIX channels 1–24. PAIR 1 MATRIX [NAME] indicator 5 MATRIX [PAIR] LED This displays the short name of the MATRIX chan- This LED will light when two adjacent odd and even- nel.
Page 266 MATRIX OUTPUT block When MATRIX channels are not paired 7 MATRIX [INS] LED This LED indicates the insertion on/off status for the MATRIX channel. When insertion is on, the LED will light, and the insert out/in point speciﬁed in the display (OUTPUT MATRIX MATRIX PATCH function INSERT PATCH screen) will be...
Page 267 MATRIX 2 [SEL] switch. The state of MATRIX 1 will be copied to MATRIX 2. For details on the parameters that are copied/linked for a pair, refer to “CS1D Reference Manual (Appendices)” ( p.45). If you wish to reset the parameters, do so from the screen.
Page 268: Matrix Layer Section
MATRIX OUTPUT block MATRIX LAYER section In this section you can select the group of channels that will be controlled by the MATRIX channel section. 1-12 MATRIX LAYER 1 MATRIX LAYER [1–12]/[13–24] switches and LEDs The channels controlled by the MATRIX channel section will change as follows, according to the switch that is turned on.
Page 269: Stereo Output Block
CS1D Reference Manual (Hardware) STEREO OUTPUT block [Function] This block mixes the signals that are sent from the input channels and the output channels to the STEREO bus, and sends them to the output units that are patched to the STEREO A/B channels. If you are using the...
Page 270 STEREO OUTPUT block TO MTRX MONO MUTE MUTE SAFE SAFE ST OUTPUT ST OUTPUT 1 STEREO [ON] switch and LED 2 STEREO A [TO MTRX] switch and LED (STEREO This is the on/off switch for the STEREO A/B chan- A channel only) nel.
Page 271 CS1D Reference Manual (Hardware) 3 STEREO B [MONO] switch and LED (STEREO B Using the STEREO A channel [SEL] switch to channel only) alternate between L and R channels This switch selects monaural or stereo output for the STEREO B channel.
Page 272 STEREO OUTPUT block 5 STEREO [INS] LED This LED indicates the insertion on/off status of the STEREO A/B channel. When insertion is on, the switch LED will light, and the insert out/in points speciﬁed in the display (OUTPUT PATCH function INSERT PATCH screen) will be enabled.
Page 273: Selected Output Channel Block
CS1D Reference Manual (Hardware) SELECTED OUTPUT CHANNEL block [Function] In this block you can set and view the parameters of the currently selected input channel (MIX channel, MATRIX channel, L or R channels of STEREO A/B). Hint If desired, you can cause the corresponding screen to automatically appear when you operate this block.
Page 274 SELECTED OUTPUT CHANNEL block [Procedure] Selecting a channel The channel to be controlled by the SELECTED OUT- PUT CHANNEL block can be selected in the following ways. 1. Using the [SEL] switch You can use the following [SEL] switches to directly select the desired output channel.
Page 275 CS1D Reference Manual (Hardware) 2. Using the SELECTED OUTPUT CHANNEL block You can use the CHANNEL SELECT [ST]/ [MATRIX]/[MIX] switches of the SELECTED OUT- PUT CHANNEL block to select the desired channel group (STEREO A/B, MATRIX, MIX), and then use the CHANNEL SELECT [ /DEC]/[ /INC] switches to step through the channels consecutively.
Page 276: Delay Section
SELECTED OUTPUT CHANNEL block DELAY section In this section you can make settings for the internal delay function. msec TIME DELAY 1 DELAY [ON] switch and LED Hint This is the on/off switch for the delay of the selected The output channel delay function provides a useful channel.
Page 277: Compressor Section
CS1D Reference Manual (Hardware) COMPRESSOR section In this section you can make settings for the internal compressor. All parameters can be controlled from the top panel except for compressor library store/recall operations, compressor type selection, and key-in signal selection. COMPRESSOR...
Page 278 SELECTED OUTPUT CHANNEL block When the compressor type is COMP or When compressor link is on, the compressor opera- EXPANDER tion will simply be linked by the key-in signal; the The encoder will set the KNEE parameter of the compressor parameters themselves will remain COMP or EXPANDER.
Page 279: Equalizer Section
CS1D Reference Manual (Hardware) EQUALIZER section This section sets the internal six-band EQ (HIGH, HIGH MID, MID, LOW MID, LOW, SUB LOW). Of the six bands, HIGH and SUB LOW EQ can be switched between shelving and peaking types. In addition, the HIGH band can function as an LPF, and the SUB LOW can function as an HPF.
Page 280: Output Section
SELECTED OUTPUT CHANNEL block 9 EQ [ ] switch & LED (SUB LOW band only) In this case, the SUB LOW band [Q] encoder will This switch changes the SUB LOW band EQ type to have no function, and its peripheral LEDs will go low shelving.
Page 281 CS1D Reference Manual (Hardware) 6 OUTPUT [TO ST PAN]/[BAL] switches and LEDs Adjusting the pan of the signal sent from a MIX These LEDs will be lit or dark to indicate the func- channel to the STEREO buttons tion controlled by the OUTPUT [PAN/BAL] encoder (5).
Page 282: Dca Section
SELECTED OUTPUT CHANNEL block DCA section This section assigns the currently selected MIX channel to a DCA group. If you wish to assign a single MIX channel to multiple DCA groups, it is convenient to use this section. [Procedure] 1 DCA [9]–[12] switches and LEDs These switches assign the currently selected MIX Using the SELECTED OUTPUT CHANNEL block channel to DCA groups 9–12.
Page 283: Safe Section
CS1D Reference Manual (Hardware) SAFE section This section sets/defeats Recall Safe and Mute Safe for the currently selected output channel. RECALL MUTE SAFE 1 SAFE [RECALL] switch and LED 2 SAFE [MUTE] switch and LED This switch sets/defeats Recall Safe for the currently...
Page 284 SELECTED OUTPUT CHANNEL block 4 CHANNEL SELECT [SHIFT] switch If you hold down this switch and press either of the CHANNEL SELECT [ /DEC]/[ /INC] switches, the number will change in steps of 12 from the cur- rent value. 5 [CHANNEL COPY] switch Use this switch to copy parameters of an output channel to a different output channel.
Page 285 CS1D Reference Manual (Hardware) Signal ﬂow for MIX channels from PRE EQ DE-EMPHASIS from INPUT PATCH MIX 1(-48) from PRE FADER to METER METER METER METER to MONITOR 6BAND COMP DELAY FADER INSERT IN MIX1(-48) KEY IN to MATRIX to METER MIX to STEREO Signal ﬂow for MATRIX channels...
Page 286: Dca Group Block
DCA GROUP block DCA GROUP block [Function] In this block, the input channel and output channel groups assigned to DCA 1–12 can be controlled as a group by the DCA faders. As necessary, you can also use these faders to directly control a desired input chan- nel or MIX channel, or boost/cut each band of the internal graphic EQ.
Page 287: Select The Items You Wish To Control From The Dca Faders
CS1D Reference Manual (Hardware) Select the items you wish to control from the DCA faders The DCA GROUP block contains twelve DCA faders. In the default state of the PM1D system, you can use these faders to control the input channel/output channel groups that are assigned to DCA 1–12. However, you can also make settings in the DCA GROUP block FADER STATUS section to change the items that will be controlled by the DCA faders.
Page 288: Dca Fader Section
DCA GROUP block DCA fader section In this section you can control the levels of the DCA groups, input channels, or MIX channels assigned to DCA groups 1–12. You can also use this section to adjust the boost/cut amount for each band of the internal graphic EQ. 1 DCA [NAME] indicator In this case, DCA faders 9–12 The upper row of indicators will show the type and...
Page 289 CS1D Reference Manual (Hardware) 6 DCA SAFE [RECALL] LED Hint If DCA groups 1–12 are assigned to the DCA faders, If the bands of the internal graphic EQ are assigned this LED will light to indicate DCA groups that are...
Page 290: Fader Status Section
DCA GROUP block FADER STATUS section In this section you can select what will be controlled by DCA faders 1–12. 1–12 13–24 25–36 37–48 FADER STATUS 1 FADER STATUS [IN]/[1–12]/[13–24]/[25–36]/[37– FADER STATUS [1–12]/[13–24]/[25–36]/[37–48] 48]/[DCA] switches and LEDs switches These switches select what will be controlled by DCA The DCA faders will control the output levels of the faders 1–12.
Page 291 CS1D Reference Manual (Hardware) [Procedure] 6. If you wish to mute a speciﬁc group, press the DCA [MUTE] switch. Using DCA faders to control DCA groups 1–12 The DCA [MUTE] switch LED will light, and the 1. Press any one of the DCA GROUP block DCA...
Page 292 DCA GROUP block 2. Click desired MODULE button located in the upper 5. Click a button to select the output channel in which left of the screen. you wish to insert the graphic EQ. The MODULE button lets you select the graphic EQ When inserting to an input channel module that you wish to control.
Page 293 DCA faders to control the graphic EQ. In this case, the [FADER STATUS] switches located above the DCA GROUP block on the CS1D top panel will function as band select switches for the bands of the graphic EQ, as shown in the following illustration.
Page 294: Master Block
MASTER block MASTER block [Function] In this block you can use functions that apply to the entire CS1D, such as talkback and oscillator operations, selecting the monitor source, and adjusting the monitor level. SOURCE SOURCE DELAY GLOBAL LAYER MASTER block...
Page 295: Talkback Section
Hint light and a +10 dB input signal will be nominal The TALKBACK 2 jack on the rear panel of the CS1D input. When off, the LED will be dark and the input provides another talkback mic input in addition to sensitivity will be –44 dB.
Page 296: Oscillator Section
LEVEL TB OUT TALKBACK OUT Frequncy: 100Hz - 10kHz to CASCADE OUT to OUTPUT PATCH TALKBACK IN +48V OSC ON OSC OUT OSC OUT PHANTOM +48V to MONITOR B to OUTPUT PATCH PINK ASSIGN LEVEL NOISE LEVEL BURST NOISE [CS1D]...
Page 297: Card Slot Section
Operation is not guaranteed for any other media. The above-listed media is normally sold in a for- matted condition. The CS1D does not have a for- matting function, so if you need to format the media, please use an external device such as a com-...
Page 298: Cue Section
MASTER block CUE section This section selects the cue point and monitoring method of the channel selected by the [CUE] switch. 1 [CUE OUT LEVEL] volume When SOLO mode is selected, the signal that is mon- This is an analog volume that sets the output level of itored from the CUE OUT jacks, MONITOR OUT the signal output from the CUE OUT jacks.
Page 299 CS1D Reference Manual (Hardware) When this switch is on (the LED will light), the signal Hint will be sent from the PFL (pre-fader listen) position On the PM1D system, Cue can be classiﬁed into the to the CUE bus. When this switch is off, the signal following three groups.
Page 300: Monitor A Section
DIGITAL 1 jack or 2-TRACK IN ANALOG 1 jacks With the default state of the PM1D, the setting of the located on the rear panel of the CS1D. MONITOR A SOURCE switches will be ignored if The choice between analog and digital is made in the even one [CUE] switch is on, and the cue (solo) sig- display (MON/CUE function 2TR IN screen).
Page 301 CS1D Reference Manual (Hardware) 2 MONITOR A DELAY [TIME] encoder and [VALUE] indicator The MONITOR A DELAY [TIME] encoder is used to set the delay time of the delay that is built into the MONITOR A output and the cue output.
Page 302: Monitor B Section
DIGITAL 1 jack or 2-TRACK IN ANALOG 1 jacks IN 3–6, or DIRECT IN) that was previously deﬁned located on the rear panel of the CS1D. by the user in the display (MON/CUE function The choice between analog and digital is made in the MONITOR B screen).
Page 303 CS1D Reference Manual (Hardware) 3 MONITOR B [ON] switch and LED Hint This is an on/off switch for the MONITOR B output. The value of this level cannot be stored in a scene or The switch LED will light when this is on.
Page 304: Engine Section
MASTER block ENGINE section If two DSP1D (or DSP1D-EX) DSP units are connected to a single CS1D, this section selects the DSP unit that will be controlled. 1 ENGINE [A]/[B] switches and LEDs PM1D system version 1.0 does not support addi- These switches select which of two DSP1D (or tional DSP units except when using Mirror mode.
Page 305: Meter Section
CS1D Reference Manual (Hardware) METER section In this section you can select the channels whose level will be shown by the level meter, and specify the level detection point. 1 METER [PRE] switch and LED 2 METER [PEAK HOLD] switch and LED...
Page 306: Scene Memory Block
SCENE MEMORY block SCENE MEMORY block [Function] In this block you can store and recall mix parameters as scene memories. Mute operations for mute groups 1– 12 are also performed in this block. RECALL MUTE RECALL PREVIEW UNDO RECALL STORE SCENE NUMBER CLEAR DIRECT RECALL...
Page 307: Scene Memory
CS1D Reference Manual (Hardware) RECALL MUTE RECALL PREVIEW UNDO RECALL STORE SCENE NUMBER CLEAR DIRECT RECALL MUTE MASTER SCENE MEMORY 1 SCENE MEMORY [1]–[12] switches and LEDs 2 SCENE MEMORY [RECALL]/[MUTE] LEDs These switches directly recall twelve previously- These LEDs indicate the function of the SCENE selected scenes from the scenes stored in memory.
Page 308 If you accidentally recall an unwanted scene, you can that scene will be reﬂected by the CS1D panel, but press this switch to return to the state prior to recall- the internal signal processing will not be affected.
Page 309 CS1D Reference Manual (Hardware) [SCENE NUMBER] For example, if you repeatedly press the SCENE MEMORY [ /INC] switch, the displayed number Immediately after you recall a will change as follows. scene, the number will be lit Scene numbers that contain no data...
Page 310 (NORMAL mode). If desired, a message can ask you to conﬁrm the recall operation when you press the SCENE MEMORY 1. Use the panel controllers of the CS1D to set the mix [RECALL] switch. parameters. This setting is made in the display (UTILITY func- 2.
Page 311 MUTE GROUP ASSIGN screen, and also in the OUT DCA/MUTE function MUTE GROUP 4. As desired, use the controls of the CS1D panel to ASSIGN screen. modify the settings. If you operate the panel controls in PREVIEW mode, 2.
Page 312 SCENE MEMORY block OUT DCA/MUTE function MUTE GROUP ASSIGN SCENE function DIRECT RECALL screen screen MUTE MASTER button Input channels can be assigned to mute groups 1– 12, and output groups can be assigned to mute groups 9–12. Hint However, it is not possible to assign both input and The function of the SCENE MEMORY [1]–[12] output channels to a mute group 9–12.
Page 313: Lcd Function Access/User Define Block
CS1D Reference Manual (Hardware) LCD FUNCTION ACCESS/USER DEFINE block [Function] In this block you can recall desired functions or screens in the display, or execute functions that were previ- ously deﬁned by the user. LCD FUNCTION ACCESS/USER DEFINE block...
Page 314: Lcd Access Global Section
LCD FUNCTION ACCESS/USER DEFINE block LCD ACCESS GLOBAL section In this section, functions that affect the entire PM1D By holding down the [SHIFT/GRAB] switch of the data system can be recalled to the display. entry section and pressing one of these switches, you can By repeatedly pressing the same switch, you can select access the previous page within that function.
Page 315: Lcd Access Input Section
CS1D Reference Manual (Hardware) LCD ACCESS INPUT section In this section, functions that affect input channels can By holding down the [SHIFT/GRAB] switch of the data be recalled to the display. entry section and pressing one of these switches, you can By repeatedly pressing the same switch, you can select access the previous page within that function.
Page 316: Data Entry Block
Data entry block Data entry block [Function] This block is used to move the display pointer (the arrow displayed in the screen) or cursor (the red circle that indicates a selection), or to modify the value of a parameter. Data entry block...
Page 317 For details refer to “CS1D Reference Manual (Soft- this switch and pressing the [DEC/CANCEL]/[INC/ ware), Other”...
Page 318: Meter Bridge Block
Meter bridge block Meter bridge block [Function] Displays the levels of the output channels and cue output. CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP MIX OUT CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP HOUR MINUTE SECOND FRAME TIME CODE...
Page 319: Meter Section (Left)
CS1D Reference Manual (Hardware) Meter section (left) CLIP CLIP CLIP CLIP CLIP CLIP CLIP CLIP MIX OUT 1 MIX OUT 1–24 meters These LED meters show the output level of MIX channels 1–24. Meter section (right) CLIP CLIP CLIP CLIP...
Page 320: Time Code Section
(LTC) that is input from the TIME CODE IN con- function TC EVENT screen) to select the source nector in the rear panel of the CS1D, or of the time (internal or external) of the time code that is dis- code that is generated within the PM1D system.
Page 321: Rear Panel Block
Rear panel block [Function] This is the block where the CS1D is connected to external devices. Here you can make connections to other devices of the PM1D system (DSP units, input/output units, power supplies), and to external audio devices such as DAT recorders, monitor systems, and MIDI devices.
Page 322: Digital I/O Section
1 DIGITAL I/O CONSOLE connectors (1/2) These are 68-pin D-sub connectors that exchange multi-channel digital audio signals with a second CS1D console when two CS1D consoles are used in a single PM1D system (Dual Console mode). Connect the ﬁrst console’s DIGITAL I/O CONSOLE connec- tor to the second console’s DIGITAL I/O ENGINE A...
Page 323: 2-Track In Digital Section
CS1D Reference Manual (Hardware) 2-TRACK IN DIGITAL section 1 2-TRACK IN DIGITAL AES/EBU jacks (1–6) 2-TRACK IN DIGITAL These are AES/EBU (XLR-3-31) jacks for inputting AES/EBU format digital sources from external devices such as CD players and DAT recorders. 2 2-TRACK IN DIGITAL COAXIAL jacks (1–2 only)
Page 324: Word Clock Section
3 75 [ON/OFF] switch This switch terminates the word clock connector. In general, this should be turned ON if the CS1D is the last device in the word clock connection chain, or if nothing is connected to the WORD CLOCK IN/ OUT connectors.
Page 325: 2-Track In Analog Section
CS1D Reference Manual (Hardware) 2-TRACK IN ANALOG section 1 2-TRACK IN ANALOG L/R jacks (1–2) 2-TRACK IN These are XLR-3-31 (balanced) jacks that input ste- ANALOG reo analog signals from external devices. Hint The signals that are input from these jacks can be...
Page 326: Talkback In 2 Section
This is an XLR-3-31 jack for connecting a talkback mic. The talkback signal that is input from this jack will be mixed within the CS1D with the signal from the TALKBACK 1 jack on the top panel, and sent to the same buses or output jacks.
Page 327: Dc Power Section
This switches the cooling fan between high and low settings. For normal use, set this to LOW. However if the CS1D is in a location of high temper- ature or is outside in direct sunlight, set this to HIGH. You should also set this to HIGH if you feel that the...
Page 328: Control Section 1
An external monitor can be connected to this con- nector to output the same image as the built-in dis- This cannot be used simultaneously with the play of the CS1D. MOUSE connector of the front panel block. Only Connect a display that supports a resolution of 800 ×...
Page 329: Control Section 2
CS1D console or internal) and the frame rate can be selected in the when two CS1D consoles are used in a single PM1D display (MIDI/GPI/TC function TC EVENT screen). system (Dual Console mode).
Page 330: Input/Output Signal Flow
The following diagram shows the signal ﬂow from the The following diagram shows the signal ﬂow from the input jacks of the CS1D until the signal is sent to the DS1D DSP unit until the signal is sent to the CS1D.
Page 331: Front Panel Block
Do not use the front panel headphone jacks at the as the track pad. same time as the top panel headphone jacks. Doing so can cause the CS1D to malfunction due to exces- This cannot be used simultaneously with the sive current.
Page 332 Reference Manual (Software)
Page 333 Contents How the “CS1D Reference Manual (Software)” is organized ....1 Printing conventions in the “CS1D Reference Manual (Software)” ... . 1 Information shown in the display .
Page 334 Contents ST OUT DIGITAL (stereo out digital) ....... . 68 MONITOR A .
Page 335 Contents INSERT/DIRECT POINT ......... 124 INSERT/DIRECT VIEW.
Page 336: How The "Cs1D Reference Manual (Software)" Is Organized
How the “CS1D Reference Manual (Software)” is organized In the “CS1D Reference Manual (Software),” the screens that appear in the display of the console (CS1D) are organized into the following four sections. This manual explains how to access the screens, the function of each part, and related procedures.
Page 337: Information Shown In The Display
CS1D Reference Manual (Software) Information shown in the display A typical screen of the CS1D The following information is shown in the display of the CS1D. [Upper part of the display (Common to each screen)] 1 DISPLAY FUNCTION 3 SEL CH (selected channel) This displays the abbreviation for the currently This shows the currently selected channel.
Page 338 This symbol will be displayed if the [CUE] switch of ager for Windows software running on your com- an input channel is on. puter. (It will not appear in the display of the CS1D.) OUTPUT CUE This symbol displayed on your computer indicates This symbol will be displayed if the [CUE] switch of that your computer and the CS1D are ofﬂine.
Page 339 CS1D Reference Manual (Software) [Center of the display] 7 Tab If a function consisting of multiple screens is selected, you can click this area to switch screens within that function. The number and content of the screens will depend on the function.
Page 340 The status of the currently selected channel and of This shows the function that is currently assigned to the CS1D will be displayed. DCA faders 1–12 of the CS1D (located in the DCA GROUP block) (“CS1D Reference Manual (Hard- ware) p.71).
Page 341: Function Menu
CS1D Reference Manual (Software) Function menu Selecting a function [Function] Here you can select the function that will be shown in the display. This menu will be the starting point when you use operations in the display to select a speciﬁc screen.
Page 342 Make settings for the meters on the top panel of the Make settings for talkback, the internal oscillator, CS1D, the meters in the meter bridge block, and the and monitor/cue ( p.62). meters that appear in the display ( p.58).
Page 343 CS1D Reference Manual (Software) 3 Input functions These buttons access functions for the input chan- nels (monaural input channels, ST IN channels). The content of each function is described below. (The abbreviated function name shown in the dis- play is given in parentheses.) PATCH (IN PATCH) Assign input units to input channels ( p.118).
Page 344: Global Functions
Global functions EFFECT functions Using internal effects 1–8 EFFECT 1–EFFECT 8 [Function] For internal effects 1–8, select the type, edit parameters, and patch inputs and outputs. Console In the LCD FUNCTION ACCESS block, press the [EFFECT] switch (press repeat- edly until the screen shown at the right appears) Display MENU button...
Page 345 L/R output channels of the internal the result in stereo. For details on the type to which effect. each effect belongs, refer to “CS1D Reference Manual (Appendices).” When you channel these buttons, a popup window will appear, in which you can select the signal.
Page 346 These parameters determine the effect. The type of effect parameters will depend on the cur- rently selected effect (3). For details on the effect parameters, refer to “CS1D Reference Manual (Appendices)”. C BALANCE This knob adjust the balance between the original (dry) sound and the effect (wet) sound.
Page 347: Effect Assign
Global functions EFFECT ASSIGN [Function] Displays a list of the effect types, the signal routes assigned to input and output, and the bypass and cue set- tings used by internal effects 1–8. Console In the LCD FUNCTION ACCESS block, press the [EFFECT] switch (press repeatedly until the screen shown at the right appears) Display...
Page 348: Geq (Graphic Eq) Functions
GEQ (graphic EQ) functions GEQ (graphic EQ) functions Using the internal 31 band graphic EQ on the output channels GEQ PARAMETER [Function] In this screen you can make settings for the twenty-four 31-band graphic EQ modules that are provided for insertion into input/output channels.
Page 349 LIMIT parameter (8). A red line displayed in the knob portion of the fader indicates that it can currently be controlled by the DCA faders of the CS1D. 0 NOTCH 1–4 Use the NOTCH 1–NOTCH 4 buttons to switch each These are four notch ﬁlters that operate on the signal...
Page 350 12-band groups and assigned to the popup window are accessed, you can hold down the DCA faders of the CS1D top panel, so that the faders panel [SHIFT/GRAB] switch and press a FADER can be used to control the boost/cut amount of each STATUS switch [1-12]/[13-24]/[25-36] to produce band.
Page 351: Geq Assign 1-12/13-24 (Graphic Eq Assign 1-12/13-24)
Global functions GEQ ASSIGN 1-12/13-24 (graphic EQ assign 1–12/13–24) [Function] This screen displays the GEQ 1–24 settings, the signal routes in which they are inserted, and the input/output levels. Console In the LCD FUNCTION ACCESS block, press the [GEQ] switch (press repeatedly until the screen shown at the right appears) Display...
Page 352 CH 1-24, CH 25-48, CH 49-72, CH 73-96 or ST IN 1-8 screens that are dis- played when you press the INPUT [GEQ] switch in the LCD FUNCTION ACCESS block of the CS1D console. A window will appear, asking you to conﬁrm the 2.
Page 353: Scene Functions
Global functions SCENE functions Operating scene memories MEMORY [Function] Store mix parameters into a scene memory, or recall a previously-stored scene. Console In the LCD FUNCTION ACCESS block, press the [SCENE] switch (press repeatedly until the screen shown at the right appears) Display MENU button SCENE button...
Page 354 LINK button is on when you VIEW] switch in the SCENE MEMORY block of the recall a scene, the library of the corresponding num- CS1D. ber will be recalled at the same time. Libraries whose TITLE EDIT...
Page 355 Global functions CLEAR Deletes the currently selected scene, and temporarily Erases the currently selected scene. saves it in the buffer memory. Scenes of other numbers will not be affected. The scenes following the deleted number will move forward by one number. Before CLEAR SCENE...
Page 356 Cancels the previously-executed Cut, Clear, Insert, or SCENE function MEMORY screen is turned off. Paste operation to return to the previous state. 1. Use the CS1D panel controls and the on-screen 4 SCENE INC/DEC (scene increment/decrement) knobs and sliders to set the mix parameters.
Page 357 You can also recall a speciﬁc channel to the SELECTED INPUT CHANNEL block or SELECTED Hint OUTPUT CHANNEL block of the CS1D, and view a By clicking the STORE UNDO button, you can speciﬁc screen in the display to see the settings in return to the state prior to when the scene memory detail.
Page 358: Recall Safe
SCENE functions RECALL SAFE [Function] Select the channels, parameters, or units that you wish to set to Recall Safe (a state of being excluded from Recall operations). For example if you have speciﬁed Recall Safe for a channel that you always want to operate manually, the parameters of that channel will not change even if you recall a new scene.
Page 359 Global functions 5 OTHERS Hint Using these buttons, elements other than the above You may select two or more parameters for the same channel parameters can be selected for Recall Safe channel (except for ALL). status. The following parameters can be selected. ALL will automatically be selected for channels for DCA 1–12 ....
Page 360: Fade Time
SCENE functions FADE TIME [Function] Make settings for the Fade function that smoothly changes the faders until they reach the levels speciﬁed by a newly selected scene. Console In the LCD FUNCTION ACCESS block, press the [SCENE] switch (press repeat- edly until the screen shown at the right appears) Display...
Page 361 Global functions 3 SET ALL When the SAME AS FADING button is on This button turns on the fade function of all chan- The Fade function will be enabled for the PAN nels. parameters of only the input channels selected in 4. The Fade function for the PAN parameter is valid 4 CLEAR ALL only for input channels and ST IN channels.
Page 362: Direct Recall
DIRECT RECALL [Function] Make settings for the Direct Recall function that allows you to use the SCENE MEMORY [1]–[12] switches (SCENE MEMORY block) of the CS1D to directly recall speciﬁc scenes. Console In the LCD FUNCTION ACCESS block, press the [SCENE] switch...
Page 363 The SCENE MEMORY [RECALL] LED (SCENE Click the line for the desired scene, and it will be MEMORY block) of the CS1D will light. In this con- selected. dition, you can press SCENE MEMORY [1]–[12] To display a scene that is not currently shown in the switches to recall the previously-assigned scenes.
Page 364: Midi/Gpi/Tc Function
When a MIDI program change is received from an external device, the event (scene recall/effect recall) that you speciﬁed for that program number will be executed. Also, when the corresponding event is executed on the CS1D, a MIDI program change message will be trans- mitted to the external device.
Page 365 When the corresponding event is executed on the received on the MIDI channel (RX CH) speciﬁed by CS1D, messages will be transmitted on the TX CH in the RX CH knob (7) will execute the event that has the sequence of Bank Select 1–16 Program been assigned to each program number.
Page 366 1. Connect the MIDI OUT connector of the external This list shows the event (scene recall/effect recall) device to the [MIDI IN] connector of the CS1D or that is assigned to each program change number. to the [MIDI IN] connector of the DSP1D-EX {DSP1D}.
Page 367 Program changes can also be transmitted from the PM1D system to an external device. To do so, con- nect the MIDI OUT connector of the CS1D or DSP1D-EX {DSP1D} to the MIDI IN connector of the external device, and execute the event on the CS1D that was assigned to the program number in step 9.
Page 368: Tc Event (Time Code Event)
TC EVENT (time code event) [Function] When LTC time code received from an external device (or time code generated within the CS1D) reaches a certain time, the speciﬁed scene will be recalled. This function will operate only while the CS1D and DSP1D are connected and operating.
Page 369 1. Connect the time code output connector of the external device to the [TIME CODE IN] connector of the CS1D or to the [TIME CODE IN] connector of the DSP1D-EX {DSP1D}. 2. Access the MIDI/GPI/TC function TC EVENT...
Page 370 MIDI/GPI/TC function 6. When you have captured each of the desired time 9. If necessary, use the knobs of the TIME CODE area locations, stop time code output on the external to make ﬁne adjustments to the captured time code device.
Page 371: Utility Functions
(as a substitute for clicking) will be enabled. SPEED This knob speciﬁes the speed at which the pointer will be moved by the built-in track pad of the CS1D or by the mouse connected to the [MOUSE] connec- tor. You can select from four levels: 1–4.
Page 372 SELECTED INPUT CHANNEL/SELECTED OUTPUT CHAN- NEL block on the CS1D. The controllers corresponding to each button and the screens that appear are as follows. Button...
Page 373: User Define
Global functions USER DEFINE [Function] Assign the function to be executed by the USER DEFINE [1]–[8] switches in the USER DEFINE block of the CS1D. Console In the LCD FUNCTION ACCESS block, press the [UTILITY] switch (press repeatedly until the screen...
Page 374 MONITOR A screen. SOURCE switch and MONITOR B SOURCE switch of the CS1D will have no effect until the next 2. From the USER DEFINE [1]–[8] switches, select the time you select the monitor source from the panel.
Page 375: Load/Save
Global functions LOAD/SAVE [Function] Load scene or library data stored on a PC ATA ﬂash storage card into the PM1D system, or save scene or library data from the PM1D system to a PC ATA ﬂash storage card. Console In the LCD FUNCTION ACCESS block, press the [UTILITY] switch (press repeatedly until the screen shown at the right appears)
Page 376 UTILITY functions 3 From No./To No. (specify range) 6 FILE SIZE These knobs specify the range (numbers) of the Display the estimated size required to save the items scene memories in SAVING MEMORY SELECT (2) selected in the SAVING MEMORY SELECT section that will be affected by the operation.
Page 377 1. Insert a PC ATA ﬂash storage card into [PC] card an existing ﬁle, the previous ﬁle will be deleted. slot A or B, located on the top panel of the CS1D. Once you have pressed the button to execute this...
Page 378 Loading a ﬁle from memory card 1. Insert a PC ATA ﬂash storage card into [PC] card slot A or B, located on the top panel of the CS1D. 2. Access the UTILITY function LOAD/SAVE screen. 3. From the list shown at the right, select the ﬁle that you wish to load, and click it.
Page 379: Sys/W.clock (System/Word Clock) Function
If the engine is the DSP1D-EX, the system will oper- Specify the system conﬁguration and connection ate with 96 monaural input channels. If the engine is method of the console (CS1D) and engine (DSP1D- the DSP1D, the system will operate with 48 monau- EX {DSP1D}).
Page 380 Digital audio signal output connectors 1/2 always you can manually switch to the other unit. (For output the same signals. If the currently enabled con- details on mirror connection, refer to “CS1D Operat- nector no longer provides a word clock, the receiving ing Manual (Start-up).”) device will automatically switch to the other connec- tor.
Page 381 Global functions This popup window will appear when a virtual unit Hint changes to a real unit. If the real unit is of the same If the state of unit connections differs from the type as the virtual unit, the unit and patch settings stored state, a popup window like the following will will be maintained when you click the OK button.
Page 382: Input Unit
SYS/W.CLOCK (system/word clock) function INPUT UNIT [Function] This screen displays the type and operating status of the cards installed in an input unit. In this screen you can also specify virtual connections of input units and cards, and make Recall Safe settings for a unit. Console In the LCD FUNCTION ACCESS block, press the [SYS/...
Page 383 Global functions Hint A card with an indication of “VIRTUAL” on a yellow background is virtually connected. If a card is indicated as “ILLEGAL” on a red back- ground, an input card is installed in an output unit (or vice versa). 3 Card assignment buttons These buttons are used to assign an I/O card to each slot of the input unit.
Page 384 SELECTOR of the DIO8 to the 5-8 position. With Hint this setting, signals will be sent from the OUTPUT When the CS1D goes off-line, and the virtually-con- A jacks to slots 1–4, and from the OUTPUT B jacks nected units/cards differ from the physically-connected to slots 5–8.
Page 385: Output Unit
Global functions OUTPUT UNIT [Function] Displays the type of card that is connected to the output unit. You can also use this screen to make virtual con- nections for output units and cards. Console In the LCD FUNCTION ACCESS block, press the [SYS/ W.CLOCK] switch (press repeat- edly until the screen shown at the right appears)
Page 386 SYS/W.CLOCK (system/word clock) function Hint A card with an indication of “VIRTUAL” on a yellow background is virtually connected. If a card is indicated as “ILLEGAL” on a red back- ground, an input card is installed in an output unit (or vice versa).
Page 387 Global functions AO8 (AO8 output unit) 6. Click the card that you wish to virtually connect. AO8-DA8 (an output unit in which eight DA Hint cards are installed) Virtually-connected cards will be indicated by “VIR- DIO8 1-4 (INPUT A jacks of DIO8 digital input/ TUAL”...
Page 388: Word Clock
SYS/W.CLOCK (system/word clock) function WORD CLOCK [Function] Although the PM1D system is designed to continue audio processing as far as possible even if there are syn- chronization-related problems or incorrect settings, word clock synchronization (audio system clock) must be established for all devices in the system. In this screen you can specify the word clock that will operate the PM1D system.
Page 389 When you change the word clock settings, noise may format) or MY8-AT (ADAT format), operation will be heard from the output jacks of the CS1D and AO8, be the same regardless of which of the four buttons particularly if an MY8-AT digital I/O card is installed you select.
Page 390 SYS/W.CLOCK (system/word clock) function If both buttons are off UNKNOWN (yellow) The 68 pin D-sub will be selected. This indicates that the clock status of that connector cannot be known, because it is a virtual connection or is unconnected. Although it is possible to select this connector, valid synchronization with the PM1D system cannot be established until an actual connection is made.
Page 391: Dither
Global functions DITHER [Function] For each output channel of the output unit, turn dithering on/off and specify the bits to which dithering will be applied. Console In the LCD FUNCTION ACCESS block, press the [SYS/W.CLOCK] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 392 SYS/W.CLOCK (system/word clock) function Output slots Output channels 2 On/off buttons These buttons switch dithering on/off in two-chan- nel units for each output slot of the output unit. 3 Bit number These buttons select the number of valid bits in two- channel units for each output slot of the output unit.
Page 393: Meter Functions
Global functions METER functions Make meter-related settings Input metering [Function] Display the input levels of input channels 1–96 {1–48} and ST IN channels 1–8 {1–4}. The location (metering point) at which the input levels are measured can also be selected. Console In the LCD FUNCTION ACCESS block, press the [METER] switch...
Page 394 POST ON....Immediately after the [ON] switch These ﬁve buttons are independent of the METER [PRE] switch in the METER section (MASTER block) of the CS1D top panel. The peak hold function will be momentarily cleared when you change the metering point. 4 PEAK HOLD If this button is on, the peak level of each meter will be held.
Page 395: Output Metering
Global functions Output metering [Function] Display the output levels of MIX channels 1–48, MATRIX channels 1–24, STEREO A/B channels, MONITOR OUT jacks A/B, and CUE OUT jacks. The location at which the output levels are measured can also be selected. Console In the LCD FUNCTION ACCESS block, press the [METER] switch...
Page 396 These buttons are linked with the METER [PRE] switch in the METER section (MASTER block) of the CS1D top panel, and their setting will also affect the level meters in the meter bridge block. When the PRE EQ or PRE FADER button is on, the METER [PRE] switch LED will light.
Page 397: Mon/Cue (Monitor/Cue) Functions
Levels of +10 dB and –44 dB are supported. When the +10 dB button is on, the TALKBACK [+10 dB] LED located on the CS1D top panel will light. 1 Level meter This level meter indicates the peak level of the signals...
Page 398 Using the Talkback function 1. Connect a talkback mic to the TALKBACK 1 jack 5 TB ON/OFF (talkback on/off) located on the CS1D top panel, and to the TALK- This switch turns talkback on/off. BACK 2 jack located on the rear panel.
Page 399: Oscillator
You can also use the ON/OFF button to switch the direct output on/off. (The ON/OFF button is linked with the [OSC OUT] switch located on the CS1D top panel.) 1 Level meter This level meter shows the output level of the oscilla- tor.
Page 400 MON/CUE (monitor/cue) functions When the PINK NOISE/BURST NOISE buttons are off A sine wave will be sent to the speciﬁed bus or output jack. 8 WIDTH & INTERVAL When burst noise is selected, these knobs adjust the time duration of the noise itself, and the spacing at which each burst will begin.
Page 401 6. Press the [OSC ON] switch located in the OSCIL- LATOR section (MASTER block) of the CS1D. (Alternatively, you can click the OSC ON/OFF but- tons located in the OSCILLATOR screen to turn the oscillator on.)
Page 402: 2Tr In (2 Track In)
MON/CUE (monitor/cue) functions 2TR IN (2 track in) [Function] Make settings for the 2-TRACK IN jacks of the CS1D. Console In the LCD FUNCTION ACCESS block, press the [MON/CUE] switch (press repeatedly until the screen shown at the right appears)
Page 403: St Out Digital (Stereo Out Digital)
Global functions ST OUT DIGITAL (stereo out digital) [Function] For the two STEREO OUT DIGIGAL jacks (A/B) of the CS1D, turn dithering on/off and specify the number of quantization bits for the output signal. Console In the LCD FUNCTION ACCESS...
Page 404: Monitor A
These are linked with the MONITOR A SOURCE MONITOR A SOURCE switch will always be output switches located on the CS1D top panel. from the MONITOR OUT jacks A. This setting is Each button corresponds to the following source.
Page 405 MONI- TOR A output. 2TR IN 3–6 ..Input signal from 2-TRACK IN DIGITAL jacks 3–6 of the CS1D When a signal of a given level is input to COMM IN, DIRECT IN..The input signal from the con-...
Page 406 0 DELAY This is linked with the [L MONO] and [R MONO] Here you can set the delay function provided for the switches in the MONITOR section of the CS1D top MONITOR/CUE bus output. panel. Use the knob to specify a delay time (0–750 msec) STEREO....L/R channels will be monitored...
Page 407: Monitor B
MONITOR B output. (Multiple selections are not possible.) These are linked with the MONITOR B SOURCE switches located on the CS1D top panel. Each button corresponds to the following source. 2TR IN1 Monitor the input signal from the 2-TRACK IN DIGITAL/ANALOG 1 jacks located on the rear panel of the CS1D.
Page 408 MATRIX 1–24 ..Output signal of MATRIX buses MONITOR B jack. 1–24 2TR IN 3–6 ..Input signal from 2-TRACK IN DIGITAL jacks 3–6 of the CS1D DIRECT IN..The input signal from the con- nector selected in the DIRECT IN SELECT section (3)
Page 409: Cue/Solo
The SOLO ON/OFF button is linked with the [SOLO] switch in the CUE section (MASTER block) of the CS1D top panel. If CUE mode is selected the [SOLO] switch LED will be dark, and if SOLO mode is selected it will blink.
Page 410 This is an on/off switch for the signal that is output from The range is –20 dB – +10 dB. the CUE OUT jacks located on the rear panel of the CS1D. This does not affect MONITOR OUT jacks A/B.
Page 411: Output Functions
Output functions OUT PATCH (output patch) functions Assign output units to output channels/insert I/O OUTPUT PATCH [Function] Patch the output jack of a card installed in an output unit or the input of an internal effect to the desired out- put channel (MIX channel, MATRIX channel, STEREO A/STEREO B channel).
Page 412 OUT PATCH (output patch) functions You may patch a single output channel to multiple Hint output jacks. However you may not patch multiple If PATCH CONFIRMATION is turned on in the output channels to a single output jack. UTILITY function PREFERENCE screen, a popup window will ask you for conﬁrmation each time you attempt to change the patch settings.
Page 413: Insert Patch
Output functions INSERT PATCH [Function] For each output channel, patch the input/output jacks where external devices such as effect processors will be inserted. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button OUTPUT PATCH...
Page 414 OUT PATCH (output patch) functions 6 Grid If you wish to use console switches to move the cur- This grid allows output jacks (horizontal lines) to be sor from the right grid (INSERT OUT) to the left patched to input channels (vertical columns). Cur- grid (INSERT IN), or in the opposite direction, hold rently-patched grids are indicated by a symbol.
Page 415: Insert Point
Output functions INSERT POINT [Function] For each output channel, switch insertion on/off, and select the insert I/O point. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button OUTPUT PATCH...
Page 416: Insert View
OUT PATCH (output patch) functions INSERT VIEW [Function] While viewing the block diagram displayed on-screen, select the insert I/O point of the desired output chan- nel. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 417 Output functions 5 INSERT ON/OFF This button switches insert on/off. It is linked to the INS. button of the OUT PATCH function INSERT POINT screen ( p.80). 6 Block diagram This is a block diagram for the currently selected output channel. Each button has the following func- tion.
Page 418: Name
OUT PATCH (output patch) functions NAME [Function] Assign a short name/long name to each MIX channel, MATRIX channel, DCA group 9–12, and STEREO A/B. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [PATCH] (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 419 Hint inputs and outputs. You can also input text from a keyboard connected to the KEYBOARD connector of the CS1D front panel. Hint This template will maintain its previous state as long as you do not initialize all memories. To return to the [Procedure] factory settings, select “INITIALIZE ALL MEMO-...
Page 420 OUT PATCH (output patch) functions 3. After you have input the characters, click the ENTER button in the screen. (Alternatively, use the [CURSOR] switches to move the cursor to the ENTER button in the screen, and press the [ENTER] switch.) The name will be registered in the name list.
Page 421: Out Insert (Output Insert) Function
Output functions OUT INSERT (output insert) function Settings for an output unit inserted into an output channel MIX 1-24 INS / MIX 25-48 INS / MATRIX 1-24 INS / ST MAS INS/UNIT LIB [Function] Make settings for the output unit that has been assigned to the insert out point of an output channel. Console In the LCD FUNCTION ACCESS block, press the OUTPUT...
Page 422 OUT INSERT (output insert) function [Screen functions] For an effect return, graphic EQ output, or talkback signal is assigned The OUT INSERT function screen displays the state of the parameter settings according to the type of unit or card that is assigned to the output channel. For an AD card with head amp (LMY2-ML) (Meter) (Meter)
Page 423 Output functions 2 A/B LINK For adjacent channels in the screen, this button links the selection of input jack A or B on an AD card with head amp. If this button is on, switching the A/B but- ton (4) of one channel will forcibly turn on the same button for the other channel.
Page 424: Out Eq (Output Equalizer) Function
OUT EQ (output equalizer) function OUT EQ (output equalizer) function Output channel EQ settings EQ PARAMETER [Function] Make 6-band EQ settings for the selected output channel. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [EQ] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 425 Output functions 4 EQ ON/OFF 6 OUTPUT EQ LIBRARY This button switches the 6-band EQ on/off. This button accesses the EQ LIBRARY window allowing you to store/recall EQ settings ( p.178). 5 EQ graph This graph displays the settings of the various EQ 7 Level meters parameters.
Page 426: Mix 1-24/Mix 25-48/Matrix 1-24/Stereo A, B
OUT EQ (output equalizer) function MIX 1-24/MIX 25-48/MATRIX 1-24/STEREO A, B [Function] This displays a list of the EQ settings for each output channel. Here you can also copy EQ settings between output channels. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [EQ] switch (press repeatedly until the desired output channel appears)
Page 427 48, MATRIX 1-24, and STEREO A/B screens that are displayed when you press the OUTPUT [EQ] switch in the LCD FUNCTION ACCESS block of the CS1D console. A window will appear, asking you to conﬁrm the copy. To execute the copy, click the OK button. To 2.
Page 428: Out Comp (Output Compressor) Function
OUT COMP (output compressor) function OUT COMP (output compressor) function Compressor settings for output channels COMP PRM (compressor parameters) [Function] Make compressor settings for the selected output channel. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [COMP] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 429 Output functions 3 Output channel number and short name 4 Type This shows the number, the short name, and the This indicates the type of the currently selected com- pairing status of the currently selected output chan- pressor. nel. You can click the heart symbol to enable/defeat pairing.
Page 430 OUT COMP (output compressor) function A RELEASE (release time) Specify the time from when the key-in signal drops Be careful not to confuse “compressor link” with below the threshold until compression is defeated. “stereo pairing of output channels.” Turning on com- pressor link simply causes the compressors to be B GAIN linked by the key-in signal;...
Page 431: Mix 1-12 - Mix 37-48/Matrix 1-12 - Matrix 13-24/Stereo A, B
Output functions MIX 1-12 – MIX 37-48/MATRIX 1-12 – MATRIX 13-24/STEREO A, B [Function] Display a list of compressor settings for each output channel. Here you can also copy compressor settings between output channels. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [COMP] switch (press repeatedly until the desired output channel appears)
Page 432 OUT COMP (output compressor) function [Procedure] Copying compressor settings to an output chan- 2. Click the OK button, and the settings will be cop- nel in the same tab (Example: copying from ied. MIX1 to MIX8) 1. Drag the mini-graph from the copy source output channel and drop it onto the copy destination out- put channel A window will appear, asking you to conﬁrm the...
Page 433 MIX 25-36, MIX 37-48, MATRIX 1-12, MATRIX 13-24 or STEREO A, B screens that are displayed when you press the OUTPUT [COMP] switch in the LCD FUNCTION ACCESS block of the CS1D console. 2. The copy destination tab screen will appear.
Page 434: Out Delay (Output Delay) Function
OUT DELAY (output delay) function OUT DELAY (output delay) function Set the channel-independent delay for output channels, and the global delay MIX 1-24 /MIX 25-48/MATRIX 1-24/STEREO A, B [Function] Set the delay for each output channel. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [DELAY] switch (press repeatedly until the screen shown at the right appears)
Page 435 Output functions BEAT Use the knob located below the numerical box to set the BPM, and the delay time will be displayed as the number of beats (quarter notes) for that tempo. FRAME The delay time will be displayed in frame units. You can use the six buttons below the FRAME button to select the number of frames per second.
Page 436: Out Dca/Mute (Output Dca/Mute) Function
OUT DCA/MUTE (output DCA/mute) function OUT DCA/MUTE (output DCA/mute) function Set DCA and mute group settings for the output channels DCA ASSIGN [Function] Assign output channels to DCA faders 9–12 and operate the DCA faders 9–12. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [DCA/ MUTE] (press repeatedly until the screen shown at the right appears)
Page 437 Output functions When a scene is recalled, the DCA group data of Recall Safe channels may be adjusted so that Recall Safe settings are consistent within DCA groups 9–12. Also when a channel library is recalled, the data that is recalled to the channel may be adjusted so that set- tings are consistent for DCA groups 9–12.
Page 438: Mute Group Assign
OUT DCA/MUTE (output DCA/mute) function MUTE GROUP ASSIGN [Function] Assign output channels to mute groups 9–12. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [DCA/ MUTE] switch (press repeatedly until the screen shown at the right appears) Display MENU button OUTPUT DCA/ MUTE button...
Page 439 Output functions Mute groups 9–12 can be used for either input chan- 2 MUTE nels or output channels. However, it is not possible These are the mute group numbers. The mute group to assign both input and output channels to the same corresponding to the grid where the cursor is cur- mute group.
Page 440: Matrix/St (Matrix/Stereo) Function
MATRIX/ST (matrix/stereo) function MATRIX/ST (matrix/stereo) function Send signals from the MIX channels, STEREO A/B channels, and SUB IN to the MATRIX buses MATRIX/ST ROUTING (matrix/stereo routing) [Function] Send signals from the MIX channels and STEREO A/B channels to the desired MATRIX bus. Console IN the LCD FUNCTION ACCESS block, press the OUTPUT...
Page 441 Output functions When using the MATRIX buses independently When using the MATRIX buses in pairs PAN knobs LEVEL knobs Adjust the panning of the sig- Adjust the send level of the LEVEL knobs nals that are sent from the signals that are sent from the Adjust the send level of the MIX channels/STEREO A/B MIX channels/STEREO A/B...
Page 442 When the POST ON button is on The signal from immediately after the MIX [ON] switch/STEREO [ON] switch on the CS1D will be sent. This parameter affects all signals that are sent from the corresponding channel to the MATRIX buses.
Page 443: Mix To Matrix
Output functions MIX to MATRIX [Function] Select a MATRIX bus, and set the level, on/off, and sent point of the signal that is sent from the MIX channel/ STEREO A/B channel to that MATRIX bus. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [MATRIX/ST] switch (press repeat- edly until the screen shown at the...
Page 444 When the POST ON button is on The signal will be sent from immediately after the MIX [ON] switch or STEREO A/B [ON] switch of the CS1D. 6 Pairing This displays the number and short name of the send source MIX channel/STEREO A/B channel and pair- ing status.
Page 445: Sub In
SUB IN [Function] Make settings for the SUB IN signal that is sent from the input jacks of the input unit or the input jacks of the CS1D directly to the MATRIX buses. Console In the LCD FUNCTION ACCESS block, press the OUTPUT...
Page 446 MATRIX/ST (matrix/stereo) function When using the MATRIX buses independently When using the MATRIX buses in pairs PAN knobs LEVEL knobs Adjust the panning of the Adjust the send level of the sig- LEVEL knobs signals that are sent from nals that are sent from the SUB Adjust the send level of the signals SUB IN to the odd-num- IN L/R channels to an odd-num-...
Page 447: Lcr
When this button is on, the STEREO B channel will (located in the SELECTED OUTPUT CHANNEL function as the CENTER channel. output block of the CS1D top panel) is not turned By adding the CENTER channel to the L/R channels of the STEREO A bus, you can implement three- channel playback.
Page 448 The master level of the CENTER channel is con- When LCR=on trolled by the fader of the STEREO B block on the CS1D. If necessary, you can also use the internal EQ or compressor of the STEREO B channel to process the signal.
Page 449: Out Ch View (Output Channel View) Function
Output functions OUT CH VIEW (output channel view) function View output channel settings CH VIEW (channel view) [Function] View the settings of the currently selected MIX channel, MATRIX channel, or STEREO A/B channel. In this screen you can also modify the parameter settings, or access individual screens. Console In the LCD FUNCTION ACCESS block, press the OUTPUT [CH...
Page 450 OUT CH VIEW (output channel view) function 4 EQ (equalizer) This area displays the on/off status of the internal EQ, the approximate response curve, and the peak level of the signal that has passed through the EQ. You can click the ON/OFF button to switch the EQ on/off, or click the mini-graph to access the EQ 7 DELAY PARAMETER popup window.
Page 451 I CUE This button monitors the output channel. It is linked with the MIX [CUE] switch, MATRIX [CUE] switch, or STEREO [CUE] switch on the CS1D top panel. J ON/OFF A CH LIBRARY (channel library) This button turns the output channel on/off. It is...
Page 452 OUT CH VIEW (output channel view) function RESET BOTH The parameters of both channels will be reset to the default settings. The channel parameters that are copied/reset when you click one of the above buttons are limited to the parameters that are linked when paired. In addition to the channel parameters, the following settings will also be copied/reset.
Page 453: Input Functions
Input functions IN PATCH functions Assign input/output units to input channels/insert I/O/direct out INPUT PATCH [Function] Patch the input jacks of the input units, 2TR IN jacks, effect returns, and talkback to the desired input channel (monaural/stereo). Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears)
Page 454 INx (AI8) ....AI8 analog input unit (x is the unit ID number) 2TR IN ....Input signal from one of the 2 TR IN connectors 1–6 on the rear panel of the CS1D console TB......Talkback signal EFF RTN .....Return signal to internal effect 1–8...
Page 455: Direct Out Patch
Input functions DIRECT OUT PATCH [Function] The signals input to the input channels are patched to the output jacks of a card installed in the output unit (AO8, DIO8), and output directly. Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display...
Page 456 IN PATCH functions 6 PATCH LIBRARY button This button is used to access the PATCH LIBRARY window in which you can save/load the patch status as a library ( p.172). 7 OUTPUT UNIT/SLOT/CH (output unit/slot/chan- nel) In order from the top, these are the type and ID number of the input unit, slot number, and output jack channel number.
Page 457: Insert Patch
Input functions INSERT PATCH [Function] For each input channel, patch the input/output jacks used for inserting external devices such as an effect pro- cessor. Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 458 IN PATCH functions Cursor movement using the [SHIFT/GRAB] switch and CURSOR [ ] switches √ ® [SHIFT/GRAB] switch 7 IN UNIT/SLOT/CH (input unit/slot/channel) In order from the top, these are the type and number ® CURSOR [ ] switch of the input unit, the slot number, and the input jack channel number.
Page 459: Insert/Direct Point
Input functions INSERT/DIRECT POINT [Function] For each input channel, switch insertion on/off, and select the insertion I/O point and the direct out point. Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button INPUT PATCH...
Page 460 IN PATCH functions 4 INSERT I/O POINT For each input channel, select the insert I/O point (the location in the signal path at which the external device will be inserted) from the following choices. PRE EQ ....Immediately before the EQ POST EQ ....Immediately after the EQ PRE COMP..Immediately before the com- pressor...
Page 461: Insert/Direct View
Input functions INSERT/DIRECT VIEW [Function] While viewing the block diagram displayed on-screen, select the insert I/O point and direct point of the desired input channel. Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 462 IN PATCH functions 5 INSERT ON/OFF This button switches insertion on/off. It has the same function as the INS. button in the INSERT/DIRECT POINT screen ( p.124). 6 Input channel block diagram This is a block diagram for the currently selected input channel.
Page 463: Name
Input functions NAME [Function] Assign a short name/long name to an input channel, or DCA. Console In the LCD FUNCTION ACCESS block, press the INPUT [PATCH] switch (press repeatedly until the screen shown at the right appears) Display MENU button INPUT PATCH button NAME tab...
Page 464 SOR] switches to move the cursor to the ENTER but- ton in the screen, and press the [ENTER] switch.) Hint You can also input text from a keyboard connected to The name will be registered in the template name the KEYBOARD connector of the CS1D front panel. list.
Page 465 Input functions Hint When the cursor is on a ﬁeld that is in an editable state (displayed in light blue), pressing the [ENTER] switch will have the same result as step 3. [Procedure] Using the template name list to assign a name to a channel/DCA A name registered in the template name list can be input directly into the name list.
Page 466: In Ha/Insert (Input Head Amp/Insert) Functions
IN HA/INSERT (Input head amp/insert) functions IN HA/INSERT (Input head amp/insert) functions Settings for the head amp/phase section of the input unit CH 1-24 – CH 73-96 / ST IN 1-8 / CH 1-24 INS – CH 73-96 INS / ST IN INS/UNIT LIB [Function] Make settings for the head amp assigned to the input channel/insert in point.
Page 467 Input functions [Screen functions] For an effect return, graphic EQ output, or talkback signal is assigned In the IN/INS screen, the state of the parameters will be displayed according to the type of unit or card that is assigned to that channel. For an AD card with head amp (LMY2-ML) (Meter) (Meter)
Page 468 IN HA/INSERT (Input head amp/insert) functions 2 A/B LINK A DE-EMPHASIS For adjacent input channels on the screen, this but- If a signal with emphasis (emphasis = ON) is input ton links the selection of input jacks A/B on an AD to the corresponding port of the digital input/output card with head amp.
Page 469: In Eq (Input Equalizer) Functions
Input functions IN EQ (Input equalizer) functions Input channel EQ settings EQ PARAMETER [Function] Set the attenuator, HPF, and four-band EQ for the selected input channel. Console In the LCD FUNCTION ACCESS block, press the INPUT [EQ] switch (press repeatedly until the screen shown at the right appears) Display MENU button...
Page 470 IN EQ (Input equalizer) functions HIGH band Center Level Frequency Crossover Gain Frequency 5 EQ ON/OFF 7 INPUT EQ LIBRARY This button switches the four-band EQ on/off. This button accesses the EQ LIBRARY window, allowing you to store/recall EQ settings ( p.176). 6 EQ graph This graph displays the settings of the various EQ 8 EQ FLAT...
Page 471 Input functions B SLOPE These buttons select the slope of the high pass ﬁlter from 6 dB, 12 dB, or 18 dB. (LOW shelving) If this button is on, LOW EQ will function as a shelv- ing ﬁlter. The Q knob will disappear. D Knobs For each band, these buttons adjust the Q, F (center frequency), and GAIN (amount of boost/cut).
Page 472: Ch 1-24 - Ch 73-96/St In 1-8
IN EQ (Input equalizer) functions CH 1-24 – CH 73-96/ST IN 1-8 [Function] View a list of the EQ settings for each input channel. Also, copy EQ settings between input channels. Console In the LCD FUNCTION ACCESS block, press the INPUT [EQ] switch (press repeatedly until the screen shown at the right appears) Display...
Page 473 CH 1-24, CH 25-48, CH 49-72, CH 73-96 or ST IN 1-8 screens that are dis- played when you press the INPUT [EQ] switch in the LCD FUNCTION ACCESS block of the CS1D console. A window will appear, asking you to conﬁrm the copy.
Page 474: In Gate/Comp Function
IN GATE/COMP function IN GATE/COMP function Gate/comp settings for the input channel GATE PRM (gate parameters) [Function] Make gate-related settings for the selected input channel. Console In the LCD FUNCTION ACCESS block, press the INPUT [GATE/ COMP] switch (press repeatedly until the screen shown at the right appears) Display...
Page 475 Input functions 3 Input channel number and short name 9 HOLD (hold time) This shows the number, the short name, and the This sets the time that the gate will remain open after pairing status of the currently selected input channel. the key-in signal falls below the threshold.
Page 476 IN GATE/COMP function E SELECT Select the key-in signal from the following choices. SELF PRE EQ Pre-EQ signal of the currently selected input channel SELF POST EQ Post-EQ signal of the currently selected input chan- LEFT CH Post-EQ signal of the previous-numbered input channel KEY IN 1–KEY IN 4 Signal of the input channel selected in the respective...
Page 477: Comp Prm (Compressor Parameters)
Input functions COMP PRM (compressor parameters) [Function] Make compressor-related settings for the selected input channel. Console In the LCD FUNCTION ACCESS block, press the INPUT [GATE/ COMP] switch (press repeatedly until the screen shown at the right appears) Display MENU button INPUT GATE/ COMP button COMP PRM tab...
Page 478 IN GATE/COMP function 4 Type This indicates the type of the currently selected com- pressor. Hint Normally, you will switch the compressor type by recalling a different type of compressor in the INPUT COMP LIBRARY window. It is not possible to change the type in this screen.
Page 479 Input functions C KNEE However you are free to subsequently turn linking This sets the sharpness of the angle at which the out- off and modify the parameter values. put level will change. A setting of HARD produces F SELECT (Key-in select) the sharpest angle, and a setting of SOFT5 produces Select the key-in signal from the following choices.
Page 480: Ch 1-12 - Ch 85-96/St In 1-4 - St In 5-8
IN GATE/COMP function CH 1-12 – CH 85-96/ST IN 1-4 – ST IN 5-8 [Function] View a list of the gate/compressor settings for each input channel. Also, copy settings between input channels. Console In the LCD FUNCTION ACCESS block, press the INPUT [GATE/ COMP] switch (press repeatedly until the screen shown at the right appears)
Page 481 Input functions [Procedures] Copying gates/compressors to an input chan- Copying gate/compressor settings to an input nels within the same tab (Example: copying channel located in a different tab (Example: from ch.1 to ch.2) copying from ch.7 to ch.20) 1. Drag the mini-graph from the copy source input 1.
Page 482 IN GATE/COMP function 3. Drag and drop the mini-graph onto the copy desti- nation input channel. A window will appear, asking you to conﬁrm the copy. To execute the copy, click the OK button. To cancel, click the CANCEL button. If you attempt to drag and drop a Gate mini-graph to Compressor (or the reverse), a warning message will appear, and the operation will not be executed.
Page 483: In Delay Functions
Input functions IN DELAY functions Make settings for individual input channel delay CH 1–24 – CH 72-96/ST IN 1-8 [Functions] Make delay settings for each input channel. Console In the LCD FUNCTION ACCESS block, press the INPUT [DELAY] switch (Press repeatedly until the desired input channel appears.) Display MENU button...
Page 484 IN DELAY functions msec (millisecond) The delay time will be displayed in millisecond units. When this button is on, the numerical boxes below and above the delay time setting knob (3) will be the same value. BEAT Use the knob located below the numerical box to set the BPM, and the delay time will be displayed as the number of beats (quarter notes) for that tempo.
Page 485: In Dca/Mute Functions
Input functions IN DCA/MUTE functions Set DCA, and mute group DCA ASSIGN [Functions] Assign input channels to DCA groups 1–12 so that they can be controlled by DCA faders 1–12. Console In the LCD FUNCTION ACCESS block, press the INPUT [DCA/ MUTE] switch (Press repeatedly until the screen shown at the right appears.)
Page 486 IN DCA/MUTE functions When a scene is recalled, the DCA data of Recall Safe 6 MUTE channels may be adjusted so that the recall safe set- These buttons switch muting on/off for each DCA tings are consistent within DCA groups 9–12. group.
Page 487: Mute Group Assign
Input functions MUTE GROUP ASSIGN [Functions] Assign input channels to mute groups 1–12. Console In the LCD FUNCTION ACCESS block, press the INPUT [DCA/ MUTE] switch (Press repeatedly until the screen shown at the right appears.) Display MENU button INPUT DCA/ MUTE button MUTE GROUP ASSIGN tab...
Page 488 IN DCA/MUTE functions assigned to a mute group 9–12 to which an output channel has already been assigned. When a scene is recalled, the mute group data of Recall Safe channels may be adjusted so that the recall safe settings are consistent within mute groups 9–12.
Page 489: Pan/Routing Function
Input functions PAN/ROUTING function Send the signal from an input channel/ST IN channel to the desired MIX bus CH to MIX (channel to mix) [Function] Send the signal from an input channel/ST IN channel to the desired MIX bus. In this screen you can also select the type (VARI or FIX) for each MIX bus.
Page 490 PAN/ROUTING function [Screen functions] MIX buses (send destination) Input channel/ST IN channels (send source) 1 Pairing 3 Send level Pairing can be selected or defeated for adjacent odd- In this section, the signal that is sent from the input numbered even-numbered MIX buses.
Page 491 Input functions When using a FIX type MIX bus independently When using FIX type MIX buses in pairs Input Input Input Input Input channel 1 Input channel 2 channel 1 channel 1 channel 2 channel 2 MIX buses 1/2 MIX buses 1/2 MIX bus 1 MIX bus 2 MIX bus 1...
Page 492 PAN/ROUTING function When using VARI type MIX buses independently When using VARI type MIX buses in pairs Input Input Input Input Input channel 1 Input channel 2 channel 1 channel 1 channel 2 channel 2 MIX buses 1/2 MIX buses 1/2 MIX bus 1 MIX bus 2 MIX bus 1...
Page 493 IN channel will be sent to the as follows. STEREO bus. This is linked with the [TO ST] switch in the SELECTED INPUT CHANNEL block of the CS1D. …… INPUT CHANNEL 7 PRE FADER/PRE EQ buttons FADER ……...
Page 494 PAN/ROUTING function settings are at different values, pan will move in tan- dem while maintaining the difference in values. This allows you to change the location while main- taining the stereo spread. INV. GANG (inverted gang) The two pan settings will be linked in the opposite direction.
Page 495: Lcr
For each input channel/ST IN channel, turn LCR mode on/off. For channels whose LCR mode is on, you can use the INPUT [PAN] encoder on the CS1D top panel to 1 CENTER BUS CONTROL simultaneously control the level of the L/R channels When this button is on, the STEREO B channel will and the CENTER channel.
Page 496 The master level of the CENTER channel is con- When LCR=on trolled by the fader of the STEREO B block on the CS1D. If necessary, you can also use the internal EQ or compressor of the STEREO B channel to process the signal.
Page 497: In Ch View (Input Channel View) Function
Input functions IN CH VIEW (input channel view) function View the settings of an input channel CH VIEW (channel view) [Function] View the settings of the currently selected input channel/ST IN channel. In this screen you can also edit the parameter settings and access individual screens.
Page 498 IN CH VIEW (input channel view) function 4 Information for the patched unit This area displays information such as the type of input unit/card assigned to that channel, the input level, gain setting, input jack A/B selection, phantom power on/off, and phase switch status. You can also use the buttons and knobs to edit the settings.
Page 499 H CUE This button is used to monitor the input channel. It is linked with the INPUT [CUE] switch on the top panel of the CS1D. I ON/OFF This button switches the input channel on/off. It is linked with the INPUT [ON] switch on the top panel of the CS1D.
Page 500 IN CH VIEW (input channel view) function 3. To pair the channels, click the CH A to B button, the CH B to A button (a channel number will appear in A and B), or the RESET BOTH button. If you decide not to specify pairing, click the CANCEL button.
Page 501: Libraries
This indicates that this number is selected for dis- play/editing. 4. Use the text palette to name the data. For details on using the text palette, refer to “CS1D Operating Manual (Basic Operation)” P.20.
Page 502 Basic library operation 5. Click the STORE button. Recalling (loading) library settings into the A window will appear, asking you to conﬁrm. PM1D system Settings that were saved in a library (or read-only preset Window to conﬁrm Store operation data) can be recalled into the PM1D system as follows. 1.
Page 503 Libraries Editing library data before recalling it Editing library data Here’s how you can edit library data within the library Data that is stored in a library can be edited within the window (before recalling it into the PM1D system), and library window (without recalling it into the PM1D sys- recall the edited data.
Page 504 Basic library operation The LIBRARY STORE popup window Changing only the name of the data If desired, you can change only the name (title) of the data in the library list. 1. Access the popup window of the desired library. For details on how to access each library, refer to the explanatory pages for the corresponding library.
Page 505: Unit Library
Libraries UNIT LIBRARY [Function] Here you can store and recall the settings (unit data) of all input/output units included in the PM1D system. Here you can also view and edit the connection state and settings of the input/output units. Display MENU button IN HA/INSERT button...
Page 506 UNIT LIBRARY Hint The APPLY EDIT button is valid only if the data of the number selected in the library list has been edited. If un-edited data is selected, and if a number marked “READ ONLY” is selected, the button text will be gray, and the button cannot be used.
Page 507: Patch Library
Libraries PATCH LIBRARY [Function] Here you can save (store) all data for input channels, output channels, and input/output jacks patched to insert I/O (patch data). Previously stored data can also be loaded (recalled) into the PM1D system. Display MENU button IN PATCH button IN PATCH/DIRECT OUT PATCH/INSERT PATCH tab...
Page 508 PATCH LIBRARY INSERT OUT ..Insert out (output channel) TITLE EDIT patch data This edits the title of the patch data currently selected in the library list. The TITLE EDIT button is valid only if data has actually been stored in the number selected in the library list.
Page 509: Name Library
Libraries NAME LIBRARY [Function] Here you can store and recall all short names and long names (name data) assigned to input channels, output channels, and DCA groups. Display MENU button IN PATCH button NAME tab NAME LIBRARY button MENU button OUT PATCH but- NAME tab NAME...
Page 510 (For details on inputting library list. If a number with no data is selected, the text and using the various buttons, refer to “CS1D button text will be gray, and the button cannot be Operating Manual (Basic Operation)”...
Page 511: Input Eq Library
Libraries INPUT EQ LIBRARY [Function] Here you can store and recall EQ settings (input EQ data) for the currently selected input channel. Display MENU button IN EQ button EQ PARAMETER tab LIBRARY button [Screen functions] 1 Edit section This area displays the settings of the input EQ data 2 Library list currently selected in the library list (2).
Page 512 INPUT EQ LIBRARY 3 STORE/RECALL buttons These buttons store/recall input EQ data. Each button has the following function. RECALL Load the currently selected input EQ data from the library list into the input channel selected in the EQ PARAMETER screen (IN GATE/COMP function). STORE Store the input EQ data currently selected in the EQ PARAMETER screen (IN GATE/COMP function) to...
Page 513: Output Eq Library
Libraries OUTPUT EQ LIBRARY [Function] Here you can store and recall EQ settings (output EQ data) for the currently selected output channel. Display MENU button OUT EQ button EQ PARAMETER tab LIBRARY button [Screen functions] 1 Edit section This area displays the settings of the output EQ data currently selected in the library list (2).
Page 514 OUTPUT EQ LIBRARY 3 STORE/RECALL buttons These buttons store/recall output EQ data. Each button has the following function. RECALL Load the currently selected output EQ data from the library list into the output channel selected in the EQ PARAMETER screen. STORE Store the output channel EQ data currently selected in the EQ PARAMETER screen to the number...
Page 515: Input Gate Library
Libraries INPUT GATE LIBRARY [Function] Here you can store and recall gate settings (input gate data) for the currently selected input channel. Display MENU button IN GATE/COMP button GATE PARAMETER tab INPUT GATE LIBRARY button [Screen functions] 1 Edit section This area displays the settings of the input gate data 2 Library list currently selected in the library list (2).
Page 516 INPUT GATE LIBRARY 3 STORE/RECALL buttons These buttons store/recall input gate data. Each button has the following function. RECALL Load the currently selected input gate data from the library list into the input channel selected in the GATE PARAMETER screen. STORE Store the gate settings of the input channel currently selected in the GATE PARAMETER screen to the...
Page 517: Input Comp Library
Libraries INPUT COMP LIBRARY [Function] Here you can store and recall compressor settings (input compressor data) for the currently selected input channel. Display MENU button IN GATE/COMP button COMP PARAMETER tab INPUT COMP LIBRARY button [Screen functions] 1 Edit section 2 Library list This area displays the settings of the input compres- This shows a list of the input compressor data stored...
Page 518 INPUT COMP LIBRARY 3 STORE/RECALL buttons These buttons store/recall input compressor data. Each button has the following function. RECALL Load the currently selected input compressor data from the library list into the input channel selected in the COMP PARAMETER screen. STORE Store the input compressor data currently selected in the COMP PARAMETER screen to the number...
Page 519: Output Comp Library
Libraries OUTPUT COMP LIBRARY [Function] Here you can store and recall compressor settings (output compressor data) for the currently selected output channel. Display MENU button OUT COMP but- COMP PARAMETER tab OUTPUT COMP LIBRARY button [Screen functions] 1 Edit section This area displays the settings of the output compres- 2 Library list sor data currently selected in the library list (2).
Page 520 OUTPUT COMP LIBRARY 3 STORE/RECALL buttons These buttons store/recall output compressor data. Each button has the following function. RECALL Load the currently selected output compressor data from the library list into the output channel selected in the COMP PARAMETER screen (OUT COMP function).
Page 521: Input Channel Library
Libraries INPUT CHANNEL LIBRARY [Function] Here you can store and recall mix parameter settings (input channel data) for the currently selected input channel. Display MENU button IN CH VIEW button INPUT CH LIBRARY button [Screen functions] 1 Edit section Hint This area displays the settings of the input channel By clicking the EQ, GATE, or COMP mini-graphs, data currently selected in the library list (2).
Page 522 For a list of the parameters that are saved in the the library list into the input channel selected in the channel library, refer to “CS1D Reference Manual CH VIEW screen (IN CH VIEW function). (Appendices)” section “Channel library list.”...
Page 523: Output Channel Library
Libraries OUTPUT CHANNEL LIBRARY [Function] Here you can store and recall mix parameter settings (output channel data) for the currently selected output channel. Display MENU button OUT CH VIEW button OUTPUT CH LIBRARY button [Screen functions] 1 Edit section Hint This area displays the settings of the output channel By clicking the EQ, GATE, or COMP mini-graphs, data currently selected in the library list (2).
Page 524 For a list of the parameters that are saved in the It is not possible to recall if the pairing state of the channel library, refer to “CS1D Reference Manual recall channel does not match the pairing state (Appendices)” section “Channel library list.”...
Page 525: Effect Library
Libraries EFFECT LIBRARY [Function] Here you can store and recall the effect settings (effect data) of the currently selected internal effect. Display MENU button EFFECT button EFFECT 1 – EFFECT 8 tabs EFFECT LIBRARY button [Screen functions] 1 Edit section This area displays the settings of the effect data cur- 2 Library list rently selected in the library list (2).
Page 526 EFFECT LIBRARY Each button has the following function. RECALL Load the currently selected effect data from the library list into the internal effect selected in the EFFECT function. STORE Store the effect data of the effect currently selected in the EFFECT function to the number selected in the library list.
Page 527: Geq Library
Libraries GEQ LIBRARY [Function] Here you can store and recall the settings (GEQ data) of the currently selected GEQ module. Display MENU button GEQ button GEQ PARAMETER tab LIBRARY button [Screen functions] 2 Library list 1 Edit section This shows a list of the GEQ data stored in memory. This area displays the settings of the GEQ data cur- The highlighted line is currently selected for opera- rently selected in the library list (2).
Page 528 GEQ LIBRARY 3 STORE/RECALL buttons These buttons store/recall GEQ data. Each button has the following function. RECALL Load the currently selected GEQ data from the library list into the GEQ module selected in the GEQ PARAMETER screen. STORE Store the settings of the GEQ module currently selected in the GEQ PARAMETER screen to the number selected in the library list.
Page 529: Other
When you initialize the memory, all previously-saved data will be erased, and cannot be recovered. Please use cau- tion. If memory contains important data, you must save it to a memory card inserted in the PC ATA STORAGE CARD slot of the CS1D before you initialize the memory. [Procedure] “INITIALIZE CURRENT SCENE”: The current...
Page 530 Reference Manual (Appendices)
Page 531 Contents Appendices ......... .1 Preset EQ Program Parameters .
Page 532 Contents Scene Memory/Effect Library to Program Change Table ....35 Channel library list ..........44 Parameters copied when pairing.
Page 533: Appendices
Appendices Preset EQ Program Parameters • INPUT EQ LIBRARY This is the EQ library that can be used on inputs. (All are read-only.) Parameter Title Description LOW MID HIGH MID HIGH PEAKING PEAKING PEAKING H.SHELF Emphasizes the low range +3.5 dB –3.5 dB ±0.0 dB +4.0 dB...
Page 534 Appendices Parameter Title Description LOW MID HIGH MID HIGH PEAKING PEAKING PEAKING H.SHELF Unlike program 09, this +3.0 dB ±0.0 dB +2.5 dB +0.5 dB program emphasizes the E.Bass 2 low range of an electric 112 Hz 112 Hz 2.24 kHz 4.00 kHz bass.
Page 535 Preset EQ Program Parameters Parameter Title Description LOW MID HIGH MID HIGH L.SHELF PEAKING PEAKING H.SHELF A variation on program –3.5 dB –2.0 dB ±0.0 dB +2.0 dB A.G.Stroke 2 20. You can also use it 300 Hz 750 Hz 2.00 kHz 3.55 kHz with a gutsy guitar sound.
Page 536 Appendices Parameter Title Description LOW MID HIGH MID HIGH L.SHELF PEAKING PEAKING H.SHELF A variation on program –9.0 dB +1.5 dB +2.0 dB ±0.0 dB Tom-tom 2 05. Emphasizes the mid 90 Hz 212 Hz 5.30 kHz 17.0 kHz and high range. —...
Page 537: Output Eq Library
Preset EQ Program Parameters • OUTPUT EQ LIBRARY This is the EQ library that can be used on outputs. (All are read-only.) Parameter Title Description HIGH HIGH PEAKING PEAKING PEAKING PEAKING PEAKING H.SHELF Use on a stereo mix dur- –0.5 dB ±0.0 dB ±0.0 dB ±0.0 dB...
Page 538: Preset Dynamics Program Settings
Appendices Preset Dynamics Program Settings Here is a list of the built-in dynamics programs. The values shown for the RELEASE, HOLD, and DECAY parameters are for a sampling frequency of 44.1 kHz. Be aware that for these parameters, the operating time and available range will change depending on the sampling frequency.
Page 539: Input Comp Library
Preset Dynamics Program Settings • INPUT COMP LIBRARY For all libraries, the INPUT FILTER is set to HPF 20 Hz OFF. [COMPANDER H] indicates COMPANDER HARD, and [COMPANDER S] indicates COMPANDER SOFT. Title [Type] Compressor effect and parameter values Comp [COMP] Compressor template preset for use on the overall mix.
Page 540 Appendices E.B.Finger [COMP] A compressor that evens out the attack and volume of a finger-plucked electric bass. THRESHOLD RATIO RANGE ATTACK OUT GAIN WIDTH RELEASE HOLD DECAY KNEE (dB) ( :1) (dB) (dB) (dB) –12 — SOFT 2 — 470m —...
Page 541 Preset Dynamics Program Settings SamplingPerc [COMPANDER S] Effective when used on sampled sounds from CD-ROM etc. are used in a Sampling BD [COMP] context of acoustic sounds, to prevent the sampled sounds from seeming Sampling SN [COMP] to lack in power or deﬁnition. Four variations are provided: Perc, BD, SN, Hip Comp [COMPANDER S] and for looped materials (Hip Comp).
Page 542: Output Comp Library
Appendices • OUTPUT COMP LIBRARY Title [Type] Compressor effect and parameter values Comp [COMP] Compressor template preset for use on the overall mix. THRESHOLD RATIO RANGE ATTACK OUT GAIN WIDTH RELEASE HOLD DECAY KNEE (dB) ( :1) (dB) (dB) (dB) –8 —...
Page 543: Compressor Types
Compressor Types Compressor Types Dynamics processors are generally used to correct or control signal levels, although they can also be used cre- atively to shape a sound’s volume envelope. The following sections explain the COMP, EXPANDER, and COMPANDER-(H/S) compressor, their parameters, and general applications. COMP The COMP processor is a compressor that attenuates [Limiter]...
Page 544 Appendices —This determines how compression is applied at When LPF (low pass ﬁlter) is on, the compressor will KNEE the threshold point. When set to hard, compression at apply to the signal that has passed through the LPF, and the speciﬁed ratio is applied as soon as the input signal the signal that has passed through the HPF will then be level exceeds the speciﬁed threshold.
Page 545: Expander
Compressor Types EXPANDER An expander is similar to a compressor except that it Parameter Range works on signals below the threshold level. By reducing THRESHOLD –54 dB to 0 dB (1 dB steps) signals below the threshold level, the expander attenu- OUT GAIN ±0.0 dB to +18.0 dB (0.5 dB steps) ates low-level noise, effectively increasing the dynamic...
Page 546: Compander (Hard & Soft)
Appendices —This determines the amount of expansion. RATIO For COMP ON and LPF ON That is, the change in output signal level relative to change in input signal level. For a 2:1 ratio, for example, a 5 dB change in input level (below the threshold) results in a 10 dB change in output level.
Page 547 Compressor Types —This determines the amount of compression. RATIO Parameter Range That is, the change in output signal level relative to THRESHOLD –54 dB to 0 dB (1 dB steps) change in input signal level. For a 2:1 ratio, for example, a 10 dB change in input level (above the threshold) OUT GAIN –18 dB to ±0.0 dB (0.5 dB steps)
Page 548: Gate Types
Appendices Gate Types GATE A gate, or noise gate is essentially an audio switch used Parameter Range to mute signals below a set threshold level. It can be used THRESHOLD –54 dB to 0 dB (1 dB steps) to cut background noise picked up by open micro- phones, noise and hiss from guitar valve amps and RANGE –70 dB to 0 dB (1 dB steps)
Page 549: Ducking
Gate Types DUCKING Ducking is commonly used for voice-over applications Parameter Range in which the background music level is reduced auto- THRESHOLD –54 dB to 0 dB (1 dB steps) matically when an announcer speaks. Ducking is achieved by triggering a compressor with a different RANGE –70 dB to 0 dB (1 dB steps) sound source.
Page 550: Preset Effects Programs
Appendices Preset Effects Programs This is a list of the effect programs built into the CS1D. Basic effect programs 01–29 are standard programs for each effect type. Advanced reverb programs 31–71 are variations of reverb-type effects, and can be used immediately in a variety of situations.
Page 551: Advanced Reverb Programs
Preset Effects Programs Guitar Effects Title Type Description Amp Simulate AMP SIMULATE Guitar Amp Simulator Dynamic Effects Title Type Description Dyna.Filter DYNA.FILTER Dynamically controlled ﬁlter. Dyna.Flange DYNA.FLANGE Dynamically controlled ﬂanger. Dyna.Phaser DYNA.PHASER Dynamically controlled phase shifter. • Advanced reverb programs Reverb Effects Title Type...
Page 552 Appendices Coliseum Reverb Long reverb of a wide space, simulating a coliseum. Fairly long reverb with a 52 ms delay between the early reﬂections Opera Reverb and the reverb. Train Station Reverb Try this when you need echoing footsteps in a late-night train station. Beauty Plate Reverb Sub-reverb settings have been boosted.
Page 553: Effects Parameters
Effects Parameters Effects Parameters These are the parameters used to edit each effect. • REVERB [Type: STEREO] Parameter Range Description Small Hall, Large Hall, Vocal Plate, REVERB TYPE Perc.Plate, Spring, Echo Room, Reverb type Strings, Snare, Reverb Flange REV TIME 0.3 - 99 [s] Reverb time INI.DELAY...
Page 554: Gate Reverb, Reverse Gate
Appendices • GATE REVERB, REVERSE GATE [Type: STEREO] Parameter Range Description ER. TYPE Type-A, Type-B Type of early reﬂection (ER.) simulation ROOM SIZE 0.1 - 20.0 Reﬂection spacing LIVENESS 0 - 10 Early reﬂections decay characteristics (0= dead, 10= live) INI.DELAY 0.0 - 500.0 [ms] Initial delay before reverb begins...
Page 555: Echo
Effects Parameters • ECHO [Type: STEREO] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 delay time DELAY L 0.0 - 2730.0 Left channel delay time NOTE L Used in conjunction with TEMPO to determine delay time Left channel feedback gain (plus values for normal-phase FB.LEVEL L –99 - +99 [%]...
Page 556: Flange
Appendices • FLANGE [Type: STEREO] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed FREQ. 0.05 - 40.00 [Hz] Modulation speed Used in conjunction with TEMPO to determine modulation NOTE speed DEPTH 0 - 100 [%]...
Page 557: Phaser
Effects Parameters • PHASER [Type: STEREO] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed FREQ. 0.05 - 40.00 [Hz] Modulation speed Used in conjunction with TEMPO to determine modulation NOTE speed DEPTH...
Page 558: Tremolo
Appendices • TREMOLO [Type: STEREO] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed FREQ. 0.05 - 40.00 [Hz] Modulation speed Used in conjunction with TEMPO to determine modulation NOTE speed DEPTH 0 - 100 [%]...
Page 559: Dual Pitch
Effects Parameters • DUAL PITCH [Type: STEREO] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 delay time PITCH L –24 - +24 Left channel pitch shift FINE L –50 - +50 [ct] Left channel pitch shift ﬁne Left channel level (plus values for normal phase, minus LEVEL L...
Page 560: Rev Chorus
Appendices • REV CHORUS [Type: MIX] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed Small Hall, Large Hall, Vocal Plate, REVERB TYPE Perc.Plate, Spring, Echo Room, Reverb type Strings, Snare, Reverb Flange REV TIME 0.3 - 99 [s] Reverb time...
Page 561 Effects Parameters • REV FLANGE [Type: MIX] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed Small Hall, Large Hall, Vocal Plate, REVERB TYPE Perc.Plate, Spring, Echo Room, Reverb type Strings, Snare, Reverb Flange REV TIME 0.3 - 99 [s]...
Page 562: Rev + Sympho
Appendices • REV SYMPHONIC [Type: MIX] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 modulation speed Small Hall, Large Hall, Vocal Plate, REVERB TYPE Perc.Plate, Spring, Echo Room, Reverb type Strings, Snare, Reverb Flange REV TIME 0.3 - 99 [s] Reverb time...
Page 563: Delay + Er
Effects Parameters • DELAY + ER. [Type: MIX] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 delay time DELAY L 0.0 - 4000.0 Left channel delay time NOTE L Used in conjunction with TEMPO to determine delay time DELAY R 0.0 - 4000.0 Right channel delay time...
Page 564: Delay + Rev
Appendices • DELAY + REV [Type: MIX] Parameter Range Description Tempo (BPM) value that is the basis for calculating the TEMPO 20 - 300 delay time DELAY L 0.0 - 4000.0 Left channel delay time NOTE L Used in conjunction with TEMPO to determine delay time DELAY R 0.0 - 4000.0 Right channel delay time...
Page 565: Amp Simulate
Effects Parameters • AMP SIMULATE [Type: MIX] Parameter Range Description STK-M1, STK-M2, THRASH, AMP TYPE MIDBST, CMB-PG, CMB-VR, Guitar amp simulation type CMB-DX, CMB-TW, MINI DST1, DST2, OVD1, OVD2, DST TYPE Distortion type (DST= distortion, OVD= overdrive) CRUNCH NOISE GATE 0 - 20 Noise reduction DRIVE...
Page 566: Dyna. Phaser
Appendices • DYNA. PHASER [Type: STEREO] Parameter Range Description SENSE 0 - 100 Sensitivity Feedback gain (plus values for normal-phase feedback, FB.LEVEL –99 - +99 [%] minus values for reverse-phase feedback) HI.RATIO 0.1 - 1.0 High-frequency feedback ratio OFFSET 0 - 100 Lowest phase-shifted frequency offset DIRECTION UP, DOWN...
Page 567: Scene Memory/Effect Library To Program Change Table
Scene Memory/Effect Library to Program Change Table Scene Memory/Effect Library to Program Change Table Initial Bank/Ch# 1 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Scene 01.0 Scene 04.2 Scene 07.4...
Page 568 Appendices Initial Bank/Ch# 3 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Scene 26.6 Scene 29.8 Scene 33.0 Scene 36.2 Scene 26.7 Scene 29.9 Scene 33.1 Scene 36.3 Scene 26.8 Scene...
Page 569 Scene Memory/Effect Library to Program Change Table Initial Bank/Ch# 5 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Scene 52.2 Scene 55.4 Scene 58.6 Scene 61.8 Scene 52.3 Scene 55.5 Scene...
Page 570 Appendices Initial Bank/Ch# 7 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Scene 77.8 Scene 81.0 Scene 84.2 Scene 87.4 Scene 77.9 Scene 81.1 Scene 84.3 Scene 87.5 Scene 78.0 Scene...
Page 571 Scene Memory/Effect Library to Program Change Table Initial Bank/Ch# 9 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1 Effect1...
Page 572 Appendices Initial Bank/Ch# 11 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3 Effect3...
Page 573 Scene Memory/Effect Library to Program Change Table Initial Bank/Ch# 13 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5 Effect5...
Page 574 Appendices Initial Bank/Ch# 15 Program Scene/ Program Scene/ Program Scene/ Program Scene/ Initial# Initial# Initial# Initial# Change# Effect Change# Effect Change# Effect Change# Effect Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7 Effect7...
Page 575 Scene Memory/Effect Library to Program Change Table Initial Bank/Ch# __ Program Scene/ Program Scene/ Program Scene/ User# User# User# Change# Effect Change# Effect Change# Effect...
Page 576: Channel Library List
Appendices Channel library list This table shows the parameters that are saved in the input channel, MIX channel, MATRIX channel, and STEREO A/B channel libraries. INPUT/ST IN MATRIX STEREO A/B INPUT CH No. MIX CH No. MATRIX CH No. STEREO CH No. Input HA Gain Link Input HA A/B Link Input Insert In HA Gain Gang...
Page 577: Parameters Copied When Pairing
Parameters copied when pairing INPUT/ST IN MATRIX STEREO A/B Mix Sub-Low EQ Type Matrix Sub-Low EQ Type Stereo Sub-Low EQ Type Input HPF SLOPE Input HPF Freq Input GATE KEY IN SELECT Input GATE TYPE Input GATE HPF Freq. Input GATE LPF Freq. Input GATE Range Input GATE Threshold Input GATE Attack...
Page 578 Appendices INPUT MATRIX Input Low EQ Type Mix Low-Mid EQ Type Matrix Low-Mid EQ Type Mix Low EQ Q Matrix Low EQ Q Mix Low EQ Freq Matrix Low EQ Freq Mix Low EQ Gain Matrix Low EQ Gain Mix Low EQ Type Matrix Low EQ Type Mix Sub-Low EQ Q Matrix Sub-Low EQ Q...
Page 579: Midi Data Format
MIDI Data Format MIDI Data Format 1. TRANSMIT/RECEIVE DATA 2. TRANSMISSION CONDITION 1.1 CHANNEL MESSAGE BANK ON CONTROL CHANGE 1.1.1 CONTROL CHANGE (Bn) BANK SELECT $BnH MIDI TX CH? PGM Tx ON PROGRAM CHANGE $CnH <<Reception>> MIDI OUT In SINGLE CH mode when BANK is ON, these messages will be ECHO ON received on the matching [Rx CH] from the MIDI IN for which BANK MIDI IN...
Page 580: Warning Message
Appendices Warning Message These messages will disappear after a short time. Message Explanation 2TR IN DIGITAL-3 SRC TURNED OFF. When WORD CLOCK was selected for 2TR IN3, SRC=ON changed to OFF. You attempted to drop an EQ/COMP/GATE/GEQ graph onto a location of a CANNOT DROP! different type.
Page 581: Error Message
About the PM1D system version checking function When the CS1D starts up, or when the connection status of the various components in the PM1D system has changed, the software/ﬁrmware version of each component is checked to verify that it can function correctly within the PM1D system.
Page 582: Troubleshooting
LCD do not light (“CS1D Reference Manual (Hardware)” p.32) Is the power cable connected to an AC outlet of the Is the fader of the input channel raised? (“CS1D Ref- correct voltage? erence Manual (Hardware)” p.32) Are the CS1D and PW1D connected by the special In SOLO mode, is CUE turned on for a channel that cable? (“CS1D Operation Manual (Start-up)”...
Page 583 Sound is output even though not patched to Are the [LAYER] or [FLIP] switches set to the appro- an output channel priate fader mode or mixing layer? (“CS1D Reference Is the signal set to DIRECT OUT? (“CS1D Operation Manual (Hardware)” p.5, 13) Manual (Basic Operation)”...
Page 584 Is EQ applied? (“CS1D Operation Manual (Basic Cannot make boost settings in the GEQ Operation)” p.57, 83) Is the LIMIT set to –24 dB? (“CS1D Operation Man- The [ON] switches and [SEL] switches select ual (Basic Operation)” p.136) the wrong channel When a scene is recalled, some time is Make sure that the correct mixing layer is selected.
Page 585: General Specifications
General Specifications General Speciﬁcations TALKBACK IN Output impedance of signal generator: 150 , MONITOR OUT ANALOG volume MAX, fs= 44.1k or 48kHz Frequency Response 20Hz-20kHz, refer to the nominal output level @1kHz INPUT OUTPUT CONDITIONS UNITS Gain: –44dB@+10dB –2 MONITOR OUT TALKBACK IN 1, 2 ANALOG Gain: +10dB@+10dB...
Page 586 Appendices Dynamic Range INPUT OUTPUT CONDITIONS UNITS 2-TRACK IN 1, 2 MONITOR OUT ANALOG ANALOG Dynamic range are measured with a 6dB/octave ﬁlter @12.7kHz; equivalent to a 20kHz ﬁlter with inﬁnite dB/octave attenuation. Crosstalk @1kHz FROM/TO TO/FROM CONDITIONS UNITS 2-TRACK IN N L 2-TRACK IN N R adjacent inputs –80...
Page 587 General Specifications Crosstalk @1kHz FROM/TO TO/FROM CONDITIONS UNITS MONITOR OUT A, B L MONITOR OUT A, B adjacent inputs –80 ANALOG R ANALOG CUE OUT L CUE OUT R adjacent inputs –80 ANALOG ANALOG PHONES OUT Output impedance of signal generator: 150Ω, fs= 44.1k or 48kHz Frequency Response 20Hz-20kHz, refer to the nominal output level @1kHz INPUT OUTPUT...
Page 588 Appendices INPUT CHANNEL CH 1-48(DSP1D) / CH 1-96(DSP1D-EX) Phase normal / reverse Input patch De-emphasis automatic de-emphasis ﬁlter (15µs/50µs) Attenuator –96 - 0dB (1dB step) High pass ﬁlter 20Hz – 600Hz (60 point) slope –6dB / –12dB / –18dB on/off Equalizer 4 band PEQ on/off...
Page 589 Direct out pre EQ / pre fader / post fader / post on Metering peak hold on/off 2-TRACK IN ANALOG 1-2 (CS1D) AD converter 24bit linear +4bit ﬂoating, 128 times oversampling. Phase normal / reverse 2-TRACK IN DIGITAL 1-6 (CS1D)
Page 590 Appendices MIX 1-48 (DSP1D, DSP1D-EX) Equalizer 6 band PEQ (SUB LOW, LOW, LOW MID, MID, HIGH MID, HIGH) bypass on/off SUB LOW / LOW SHELVING / HPF HIGH / HIGH SHELVING / LPF parameter are as same as input CH Equalizer Compressor parameter are as same as input CH Compressor.
Page 591 24bit linear +3bit ﬂoating, 128 times oversampling. DIGITAL OUTPUT (DIO8) Option card MY8, MY4 series MONITOR OUT A (CS1D) Select switch 2TR IN 1 / 2TR IN 2 / STEREO A / STEREO B / DEFINE / DIRECT IN Monitor mode...
Page 592: Controls & Indicators
Appendices SCENE MEMORIES Number of factory presets Number of scene memories SIGNAL DELAY fs= 48kHz PATH DELAY TIME ANALOG IN(AI8 plus LMY card) INPUT(DSP1D) MIX(DSP1D) ANALOG OUT(AO8 plus LMY MAX 3.1msec card) ANALOG IN(AI8 plus LMY card) INPUT(DSP1D) STEREO OUT(DSP1D) ANALOG OUT(AO8 MAX 3.1msec plus LMY card)
Page 593 Controls & Indicators ST IN BLOCK Keys (w/ LED) ST IN 1-4/5-8 ON, ST IN 1-4/5-8 L SEL, ST IN 1-4/5-8 R SEL ST IN 1-4/5-8 TO ST, ST IN 1-4/5-8 CUE Keys ST IN 1-4/5-8 ASSIGN DCA Faders ST IN 1-4/5-8 Rotary encoders (w/ 25 points LEDs) ST IN 1-4/5-8 GAIN, ST IN 1-4/5-8 PAN, ST IN 1-4/5-8 MIX 4 digits 5 x 7 dot LED...
Page 594 Appendices SELECTED INPUT CHANNEL BLOCK Keys (w/ LED) PHANTOM +48V, PHASE, INSERT, DELAY ON, INPUT A SELECT, INPUT B SELECT MIX SEND 1-24/25-48 ON, MIX SEND 1-24/25-48 PRE MIX SEND LAYER 1-24, MIX SEND LAYER 25-48 COMPRESSOR ON, COMPESSOR LINK COMPRESSOR ATTACK SELECT COMPRESSOR RELEASE SELECT COMPRESSOR FILTER ON...
Page 595 Controls & Indicators SELECTED OUTPUT CHANNEL BLOCK Keys (w/LED) DELAY ON COMPRESSOR ON, COMPESSOR LINK COMPRESSOR ATTACK/RELEASE SELECT COMPRESSOR FILTER ON EQ ON, HPF ON, LPF ON, HIGH SHELF ON LOW SHELF ON, BYPASS ON, CUE, INSERT, TO ST, TO MATRIX TO ST PAN SELECT, BAL SELECT DCA ASSIGN 9-12, RECALL SAFE, MUTE SAFE CHANNEL COPY, ST SELECT, MATRIX SELECT...
Page 596 Appendices LCD FUNCTION ACCESS, USER DEFINE BLOCK Keys (w/ LED) USER DEFINE 1-8 Keys EFFECT, GEQ, SCENE, MIDI/GPI/TC, UTILITY SYS/W.CLOCK, METER, MON/CUE INPUT PATCH, INPUT HA/INSERT, INPUT EQ INPUT GATE/COMP, INPUT DELAY, INPUT DCA/MUTE INPUT PAN/ROUTING, INPUT CH VIEW OUTPUT PATCH, OUTPUT INSERT, OUTPUT EQ OUTPUT COMP, OUTPUT DELAY, OUTPUT DCA/MUTE OUTPUT MATRIX/ST, OUTPUT CH VIEW MASTER BLOCK...
Page 597: Analog Input Characteristics
Analog Input Characteristics METER BRIDGE BLOCK 8 digits 7 segment LED TIME CODE 3 digits 7 segment LED SCENE MEMORY NUMBER 16 digits 5 x 7 dot LED SCENE MEMORY NAME LEDs SCENE MEMORY CURRENT, SCENE MEMORY PREVIEW MIX OUT 1-24 meter 21 elements MIX OUT 25-48 / MATRIX OUT 1-24 meter 21 elements STEREO A L, R meter 21 elements STEREO B L, R meter 21 elements...
Page 598: Digital Input & Output Characteristics
Appendices Digital Input & Output Characteristics CONNECTOR INPUT/OUTPUT FORMAT LEVEL TERMINALS TYPE QUANTITY DIGITAL I/O — RS422 D-SUB Half Pitch Connector 68P ENGINE A1, A2 (Female) ENGINE B1, B2 CONSOLE 1, 2 2-TRACK IN DIGITAL AES/EBU RS422 XLR-3-31 type Connector AES/EBU 1-6 2-TRACK IN DIGITAL IEC60958...
Page 599: Pin Assignment Digital I/O Engine A1, A2, B1, B2 (D-Sub Half Pitch Connector 68P)
Pin Assignment DIGITAL I/O ENGINE A1, A2, B1, B2 (D-SUB Half Pitch Connector 68P) Pin Assignment DIGITAL I/O ENGINE A1, A2, B1, B2 (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal 2TRK 1 OUT (+) 2TRK 1 OUT (–) 2TRK 2 OUT (+) 2TRK 2 OUT (–) 2TRK 3 OUT (+)
Page 600: Pin Assignment Digital I/O Console
Appendices Pin Assignment DIGITAL I/O CONSOLE 1, 2 (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal 2TRK 1 IN (+) 2TRK 1 IN (–) 2TRK 2 IN (+) 2TRK 2 IN (–) 2TRK 3 IN (+) 2TRK 3 IN (–) 2TRK 4 IN (+) 2TRK 4 IN (–)
Page 601: Pin Assignment Gpi (D-Sub Connector 25P)
Pin Assignment GPI (D-SUB Connector 25P) Pin Assignment GPI (D-SUB Connector 25P) Pin No. Signal Pin No. Signal Data OUT 1 Data OUT 2 Data OUT 3 Data OUT 4 Data OUT 5 Data OUT 6 Data OUT 7 Data OUT 8 Data IN 1 Data IN 2 Data IN 3...
Page 602: Pin Assignment Output A,B,C
Appendices Pin Assignment OUTPUT A,B,C (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal Data OUT 1-2 (+) Data OUT 1-2 (–) Data OUT 3-4 (+) Data OUT 3-4 (–) Data OUT 5-6 (+) Data OUT 5-6 (–) Data OUT 7-8 (+) Data OUT 7-8 (–) Data OUT 9-10 (+)
Page 603: Pin Assignment Input A,B (D-Sub Half Pitch Connector 68P)
Pin Assignment INPUT A,B (D-SUB Half Pitch Connector 68P) Pin Assignment INPUT A,B (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal Data IN 1-2 (+) Data IN 1-2 (–) Data IN 3-4 (+) Data IN 3-4 (–) Data IN 5-6 (+) Data IN 5-6 (–) Data IN 7-8 (+)
Page 604: Pin Assignment Digital I/O Input
Appendices Pin Assignment DIGITAL I/O INPUT 1-10 (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal Data IN 1-2 (+) Data IN 1-2 (–) Data IN 3-4 (+) Data IN 3-4 (–) Data IN 5-6 (+) Data IN 5-6 (–) Data IN 7-8 (+) Data IN 7-8 (–) Data IN 9-10 (+)
Page 605: Pin Assignment Digital I/O Output 1-6 (D-Sub Half Pitch Connector 68P)
Pin Assignment DIGITAL I/O OUTPUT 1-6 (D-SUB Half Pitch Connector 68P) Pin Assignment DIGITAL I/O OUTPUT 1-6 (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal Data OUT 1-2 (+) Data OUT 1-2 (–) Data OUT 3-4 (+) Data OUT 3-4 (–) Data OUT 5-6 (+) Data OUT 5-6 (–)
Page 606: Pin Assignment Digital I/O Cascade In (D-Sub Half Pitch Connector 68P)
Appendices Pin Assignment DIGITAL I/O CASCADE IN (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal MIX IN 1-4 (+) MIX IN 1-4 (–) MIX IN 5-8 (+) MIX IN 5-8 (–) MIX IN 9-12 (+) MIX IN 9-12 (–) MIX IN 13-16 (+) MIX IN 13-16 (–) MIX IN 17-20 (+)
Page 607: Pin Assignment Digital I/O Cascade Out (D-Sub Half Pitch Connector 68P)
Pin Assignment DIGITAL I/O CASCADE OUT (D-SUB Half Pitch Connector 68P) Pin Assignment DIGITAL I/O CASCADE OUT (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal MIX OUT 1-4 (+) MIX OUT 1-4 (–) MIX OUT 5-8 (+) MIX OUT 5-8 (–) MIX OUT 9-12 (+) MIX OUT 9-12 (–)
Page 608: Pin Assignment Digital I/O Console
Appendices Pin Assignment DIGITAL I/O CONSOLE 1,2 (D-SUB Half Pitch Connector 68P) ç Pin No. Signal Pin No. Signal 2TRK 1 IN (+) 2TRK 1 IN (–) 2TRK 2 IN (+) 2TRK 2 IN (–) 2TRK 3 IN (+) 2TRK 3 IN (–) 2TRK 4 IN (+) 2TRK 4 IN (–) 2TRK 5 IN (+)
Page 609: Pin Assignment Control I/O Remote
Pin Assignment CONTROL I/O REMOTE RS-422 (D-SUB Connector 9P) Pin Assignment CONTROL I/O REMOTE RS-422 (D-SUB Connector 9P) Pin No. Signal Pin No. Signal TX (–) TX (+) RX (+) RX (–) Pin Assignment CONTROL I/O GPI (D-SUB Connector 25P) Pin No.
Page 610 Appendices Accessories 10m × 1 DIGITAL AUDIO CABLE 10m × 2 CONTROL CABLE × 4 LAMP × 1 DUST COVER × 1 OWNER’S MANUAL × 1 PM1D SYSTEM SOFTWARE DISC (CD-R media) Dimensions 1906 Unit: mm Speciﬁcations and external appearance subject to change without notice. For European Model Purchaser/User Information speciﬁed in EN55103-1 and EN55103-2.
Page 611: Cards Specifications
Cards Specifications Cards Speciﬁcations • LMY2-ML 1. GENERAL SPECIFICATIONS Output impedance of signal generator: 150 , fs=44.1k or 48kHz. Frequency Response 20Hz-20kHz, refer to the nominal output level @1kHz CONDITIONS INPUT OUTPUT UNITS Gain: –68dB@+10dB –3 CH1A, 1B LMY4-DA CH2A, 2B Gain: +10dB@+10dB –2 Gain Error @1kHz...
Page 612: Lmy4-Ad
Appendices • LMY4-AD 1. GENERAL SPECIFICATIONS Output impedance of signal generator: 150 , fs=44.1k or 48kHz. Frequency Response 20Hz-20kHz, refer to the nominal output level @1kHz INPUT OUTPUT CONDITIONS UNITS CH1–4 LMY4-DA @+10dB –2 Gain Error @1kHz INPUT OUTPUT CONDITIONS UNITS CH1–4 LMY4-DA...
Page 613: Lmy4-Da
Cards Specifications • LMY4-DA 1. GENERAL SPECIFICATIONS Output impedance of signal generator: 150 , fs=44.1k or 48kHz. Frequency Response 20Hz-20kHz, refer to the nominal output level @1kHz INPUT OUTPUT CONDITIONS UNITS Gain sw: +24dB@+10dB –2 LMY4-AD CH1–4 Gain sw: +18dB@+4dB –2 Gain sw: +15dB@+1dB –2...
Page 614 YAMAHA CORPORATION Pro Audio & Digital Musical Instrument Division V509020 R41 1 IP P.O. Box 3, Hamamatsu, 430-8651, Japan 08 06 100 AP Printed in Japan...
Page 615: Midi Implementation Chart
YAMAHA [Digital Audio Mixing System] Date: 25 Dec. 2000 MIDI Implementation Chart Model: PM1D Version: 1.0 Function... Transmitted Recognized Remarks Basic Default 1–16 1–16 Memorized Channel Changed 1–16 1–16 Default OMNI off/OMNI on Mode Messages Memorized Altered ************** Note 0–127...
Page 616 METER METER METER METER INSERT to MONITOR FADER 6BAND INSERT COMP DELAY ATT. TO ST to CS1D 4BAND CH 1 B GATE COMP DELAY EMP. DECODE FIXED MIX PAN INSERT IN ST A Lch FADER CH 1(-48) POST KEY IN...
Page 617 PM1D System V2.0 Level Diagram Analog Analog Digital Digital (LMY4-DA,CS1D) (LMY2-ML) UNIT DSP1D DSP1D UNIT Analog Digital GAIN DIGITAL PHASE PATCH ATT. GATE COMP DELAY LEVEL PAN/SEND COMP DELAY MASTER MASTER PATCH DITHER Analog GAIN EMPHASIS DECODE LEVEL LEVEL Adder...

Yamaha CS1D Owner's Manual

Operating Manual (Start-Up)

Operating Manual (Basic Operation)

Chapter 1. Introduction

Chapter 2. The User Interfaces of the CS1D

Chapter 3. Audio Connections and Patching

Chapter 4. Basic Operation for Input Channels

Chapter 5. Basic Operation for Output Channels

Chapter 6. Insert and Direct out

Chapter 7. DCA Groups/Mute Groups

Chapter 8. Scene Memory

Chapter 9. Recall Safe/Mute Safe

Chapter 10. Monitor

Chapter 11 . Talkback/Oscillator

Chapter 12. Internal Effects

Chapter 13. Graphic EQ

Chapter 14. MIDI/Time Code

Chapter 15. Using a Memory Card to Save/Load Data

Chapter 16. Various Settings

Reference Manual (Hardware)

Reference Manual (Software)

Quick Links

Chapters

Related Manuals for Yamaha CS1D

Summary of Contents for Yamaha CS1D