Kenwood NEXEDGE NX-200 Function Reference page 523

22 FUNCTION PORTS
22.2 D-sub 25-pin Connector (Mobile Only)
Status Memory (AUX Output Status Message)
Status Memory (AUX Output Status Message) can be used to retain the output status of AUX Output Status Message 1 to
AUX Output Status Message 3.
If this function is enabled, the output status of each of AUX Output Status Message 1 to AUX Output Status Message 3 is
retained. When the transceiver is turned ON, the transceiver restores the last status prior to the transceiver being turned
OFF (high level or low level).
If this function is disabled, the output status of each of AUX Output Status Message 1 to AUX Output Status Message 3 is
not retained and the port always goes high level when the transceiver is turned ON.
Configuration using KPG-111D/ DN
Configuring the Status Memory (AUX Output Status Message) (
Functions Used for Sending by Using the External PTT (Voice), External PTT (Data)
and Data PTT Ports
Following functions used for sending by using the External PTT (Voice), External PTT (Data) and Data PTT ports can be
configured using KPG-111D/ DN.
Configuration
Which modulation line will be enabled can be configured for the External PTT (Voice), External PTT (Data) and Data
PTT ports. The following modulation lines are available.
• Mic Line
Whether to enable the audio line of the microphone that is connected to the microphone connector of the transceiver
when transmitting by using the Mic PTT, External PTT (Voice), External PTT (Data) and Data PTT ports can be
configured.
• MI2 Line
Whether to enable the audio modulation line of the D-sub 25-pin connector of the transceiver when transmitting by
using the Mic PTT, External PTT (Voice), External PTT (Data) and Data PTT ports can be configured.
If the transceiver transmits by using the External PTT (Voice) port, the transceiver is often configured to be
Modulation Line
modulated only by the MI2 Line.
• DI Line
Whether to enable the data modulation line of the D-sub 25-pin connector of the transceiver when transmitting by
using the Mic PTT, External PTT (Voice), External PTT (Data) and Data PTT ports can be configured.
If the transceiver transmits by using the External PTT (Voice) or Data PTT port, the transceiver is often configured
to be modulated only by the DI Line.
However, the DI Line is deactivated if the transceiver transmits on the following channels and GID.
• A channel where "Mixed" is configured for the Channel Type and "NXDN" is configured for Transmit Mode
• A channel in an NXDN Conventional system
• A GID in an NXDN Trunking system
Whether to multiplex the QT tone or DQT code configured for a channel in the Conventional Group when
With QT/DQT transmitting by using the Mic PTT, External PTT (Voice), External PTT (Data), and Data PTT ports can be
configured. Normally, QT tone or DQT code is configured to be multiplexed.
Whether to send the STE (Squelch Tail Eliminator) after sending the QT tone or DQT code configured for a channel
in the Conventional Group by using the Mic PTT, External PTT (Voice), External PTT (Data), and Data PTT ports
With STE can be configured. Normally, the transceiver is configured to send the STE.
Sending the Squelch Tail Eliminator eliminates the noise that occurs in the receiving transceiver when transmission
ends.
Configuration using KPG-111D/ DN
Configuring functions used for sending by using the External PTT (Voice), External PTT (Data) and Data PTT (
FPRG 8.30.4 Modulation Line Tab)
FUNC (K)/Ver 4.00
Table 22-9 External PTT (Voice), External PTT (Data), Data PTT
See FPRG 8.30.2 AUX Tab)
Operation
CONTENTS
See
INDEX 489