Kenwood NEXEDGE NX-200 Function Reference page 267

9 NXDN TRUNKING SYSTEM
9.13 Sending and Receiving a Long Message (Long Data Call)/ 9.14 Communicating with a Telephone (Telephone Call)
9.13 Sending and Receiving a Long Message (Long Data Call)
Refer to 8.11 Sending and Receiving a Long Message (Long Data Call) on page 169
SYSTEM.
9.14 Communicating with a Telephone (Telephone Call)
Telephone Call is the function to initiate voice communications using a telephone by connecting to a telephone line such as
PSTN and PABX.
A call can be initiated from the transceiver to a telephone, and from a telephone to the transceiver.
Initiating a Telephone Call
Telephone Call can be started by one of the following methods.
 Autodial Mode
A Telephone Call can be initiated by selecting the DTMF code configured in the Autodial List, or directly entering a
DTMF code and pressing the PTT switch, the Side 2 key (NX-200/ NX-210/ NX-300/ NX-410/ NX-411), or the Square
key (Mobile) in Autodial Mode. (Refer to
Pressing the Autodial key causes the transceiver to enter Autodial Mode.
Or, pressing the Menu key causes the transceiver to enter Menu Mode, and then selecting "Autodial" will cause the
transceiver to enter Autodial Mode. (Refer to
 Keypad entry
If "Autodial" is configured for Keypad Operation, pressing a key(s) on the keypad causes the transceiver to enter Autodial
Mode. The transceiver will be on hold as the first digit of the DTMF code is entered. A Telephone Call can be initiated by
entering a DTMF code and pressing the PTT switch, the Side 2 key (NX-200/ NX-210/ NX-300/ NX-410/ NX-411), or the
Square key (Mobile). (Refer to
 Call key
A Telephone Call can be initiated by pressing one of the Call 1 to Call 6 keys. A DTMF code of the target transceiver
can be configured for the Call 1 to Call 6 keys by selecting one DTMF code from the Autodial List by using KPG-111D/
DN. (Refer to Sending the DTMF Code with a Single Touch (Call 1 to Call 6 Keys) on page
 Selcall on PTT
The transceiver initiates a Telephone Call when the PTT switch is pressed on a GID where "Telephone Call" is
configured for Selcall on PTT. A DTMF code of the target transceiver can be configured by selecting one DTMF code
from the Autodial List by using KPG-111D/ DN.
 Response to incoming calls
When the transceiver receives a Telephone Call, the transceiver can respond to the transmitting transceiver by
pressing the PTT switch, the Side 2 key (NX-200/ NX-210/ NX-300/ NX-410/ NX-411), or the Square key (Mobile)
while "PHONE CALL" appears on the main display.
Note
• To use the speed dial, the dial number needs to be entered as "**nnn". A maximum of 3 numerical digits between 001 and 255 needs
to be entered in "nnn". For example, if the speed dial number is "1", "**001" needs to be entered. If "nnn" is not within the extent, the
transceiver does not initiate a Telephone Call and a Warning Tone A sounds from the transceiver.
• For NX-200S/ NX-300S, the transceiver cannot initiate a Telephone Call with keypad entry or by using Autodial Mode.
FUNC (K)/Ver 4.00
Sending a DTMF Code Selecting from a List (Autodial List) on page
3.4 Using Menu Mode on page
Sending Entered DTMF Codes All at Once (Store & Send) on page
in 8 NXDN CONVENTIONAL
23.)
361.)
366.)
CONTENTS INDEX
365.)
233