Canon imageRUNNER ADVANCE C2030 Service Manual page 721

■ NETWORK
COPIER > TEST > NETWORK
PING Network connection check
Lv.1 Details To check connection between this machine and TCP/IP network.
Use case - When checking network connection at the time of installation
- At network connection failure
Adj/set/operate method "1) Turn OFF the main power switch.
2) Connect the network cable to this machine, and then turn ON the
main power switch.
3) Inform the system administrator at user's site that installation of
this machine is complete, and ask for network setting.
4) Ask the system administrator to check the network connection,
and check the remote host address of PING transmission target.
5) Select the item and enter the remote host address, and then press
OK key and Start key.
OK: Connection is normal. Checking procedure is complete.
NG: Connection failed. Go to step 6) if the cable connection is OK. In
case of cable connection failure, connect again and then go to step 5).
6) Select the item and enter loopback address, and then press OK
key and Start key.
OK: TCP/IP setting of this machine is normal. Go to step 7) to check
NIC.
NG: TCP/IP setting of this machine has failure. Go to step 3) to
check the setting again.
7) Select the item and enter the local host address, and then press
OK key.
OK: Network setting of this machine and NIC are normal. Inform the
system administrator that the trouble is due to network environment
and ask for countermeasure.
NG: Connection failure/fault with NIC. Check connection of NIC/
replace NIC."
Display/adj/set range 0.0.0.0 to 255.255.255.255
At normal state: OK
At failure occurrence: NG
Supplement/memo - Remote host address: IP address of PC terminal in network.
- Loopback address: 127.0.0.1. Checking TCP/IP of this machine is
available because the signal is returned before NIC.
- NIC: Network interface board
- Local host address: IP address of this machine
8
Service Mode > COPIER > TEST > NETWORK
8 Service Mode > COPIER > TEST > NETWORK
COPIER > TEST > NETWORK
BML-DISP Set System Monitor scrn: BMlinks support
Lv.2 Details To set whether to only display the device configuration in the System
Monitor screen when supporting BMlinks.
When the setting is switched, the Status and Log are not displayed.
Use case When supporting BMlinks
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: Ordinary System Monitor screen
1: Screen in which only the device configuration is displayed
Default value 0
IPV6-ADR Setting of PING send address (IPv6)
Lv.1 Details To set the IPv6 address to send PING.
When PING is sent to this address by COPIER> TEST> NETWORK>
PING-IP6, the network connection condition in the IPv6 environment
can be checked.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution - Enter a consistent character string as an address of IPv6.
- Enter an address within 39 characters including hexadecimal
numbers (0-9, a-f) and a separator (:).
Related service mode COPIER> TEST> NETWORK> PING-IP6
PING-IP6 PING transmission to IPv6 address
Lv.1 Details To send PING to the address specified by IPV6-ADR.
The network connection condition in the IPv6 environment can be
checked.
Adj/set/operate method Select the item, and then press OK key.
Related service mode COPIER> TEST> NETWORK> IPV6-ADR
IPSECPOL Polling test of IPSec Encryption Board
Lv.1 Details To execute polling test of IPSec Encryption Board.
To check whether a hardware failure has occurred.
Use case When checking whether a hardware failure has occurred to the
IPSec Encryption Board
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range At normal state: OK
At failure occurrence: NG (0: The board cannot be recognized. 1: An
error occurred to the result.)
Required time Approx. 3 minutes
IPSECINT Interrupt test of IPSec Encryption Board
Lv.1 Details To execute the interrupt test of IPSec Encryption Board.
To check whether a hardware failure has occurred.
Use case When checking whether a hardware failure has occurred to the
IPSec Encryption Board
Adj/set/operate method Select the item, and then press OK key.
Display/adj/set range At normal state: OK
At failure occurrence: NG (0: The board cannot be recognized. 1: An
error occurred to the result.)
Required time Approx. 3 minutes
8-169
T-8-58
8-169