Canon imageRUNNER ADVANCE C2030 Service Manual page 666

■ DSPLY-SW
COPIER > OPTION > DSPLY-SW
UI-COPY Display/hide of copy screen
Lv.2 Details To set whether to display or hide the copy function.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
UI-BOX Display/hide of Inbox screen
Lv.2 Details To set whether to display or hide the Inbox function.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: No Inbox function (Storing is not available even with PDL to Inbox.)
1: Inbox function is active
2: Inbox function is active (with limitation; Storing is available with PDL
to Inbox despite no display on the Control Panel/remote UI)
Default value 1
Related user mode Preferences> Display Settings> Store Location Display Settings> Mail
Box
The setting value is changed to 2 when turning OFF the foregoing user
mode, and the value is changed to 1 when turning ON the mode at
power-off/on.
As the setting value of this service mode is changed, the setting value
of the foregoing user mode is also changed.
UI-SEND Display/hide of send screen
Lv.2 Details To set whether to display or hide the SEND function.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
UI-FAX Display/hide of FAX screen
Lv.2 Details To set whether to display or hide the FAX function.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 1
8
Service Mode > COPIER > OPTION > DSPLY-SW
8 Service Mode > COPIER > OPTION > DSPLY-SW
COPIER > OPTION > DSPLY-SW
T-LW-LVL Display timing of toner level warning mssg
Lv.2 Details To set the threshold value of residual toner in the toner bottle.
When the residual toner level becomes lower than the threshold, a
warning message of "Toner is low. Replacement not yet needed." is
displayed on the Control Panel.
Use case - Upon user's request
- At the timing that the service engineer visits to the customer, etc.
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When setting a value smaller than the initial value, absence of toner
may be displayed before toner level warning message.
Display/adj/set range 5 to 100
Unit 1%
Default value 10
NWERR-SW OFF/ON of network-related error display
Lv.2 Details To set OFF/ON of network-related error message display.
When setting "0: OFF" while the machine is not connected to network,
the error message "Check the network connection." is not displayed.
Use case When using the machine as a copy machine
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1: Normal model, 0: Self-copy model
FXMSG-SW ON/OFF of Fixing Assembly replace mssg
Lv.2 Details To set whether to display the message prompting the replacement of
Fixing Assembly on the Control Panel when the life judgment counter
reaches the specified value.
When FXMSG-SW is 1 and COPIER> OPTION> FNC-SW>
FXWRNLVL is 1 (default: 0), the life of Fixing Assembly is detected.
When the Fixing Assembly reaches the end of life, the Fixing Assembly
replacement message: "Prepare new fixing roller. Call service
representative." is displayed.
When the message is displayed, go through the following procedure.
1) After turning OFF the main power switch, replace the Fixing Film
Unit+Pressure Roller and Fixing Assembly.
2) After turning ON the main power switch, execute COPIER>
FUNCTION> CLEAR> CNT-DCON.
3) Turn OFF/ON the main power switch.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode COPIER> OPTION> FNC-SW> FXWRNLVL
COPIER> FUNCTION> CLEAR> CNT-DCON
8-114
8-114