Canon imageRUNNER ADVANCE C2030 Service Manual page 696

COPIER > OPTION > USER
CNT-SW Set default dis items on charge counter
Lv.1 Details To set default display items of the charge counter on the Counter
Check screen.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0:
Counter 1 - Total 1: 101
Counter 2 - Total (Black 1): 108
Counter 3 - Copy (Full Color + Single Color/1): 232
Counter 4 - Print (Full Color + Single Color/1): 324
1:
Counter 1 - Total 2: 102
Counter 2 - Copy (Full Color + Single Color/2): 231
Counter 3 - Total A (Full Color + Single Color/2): 148
Counter 4 - Copy (Black 2): 222
Counter 5 - Total A (Black 2): 133
Default value 0
PRJOB-CP Set count TX at RX/report print
Lv.2 Details To set to enable/disable a page-basis count pulse transmission to the
charging management device at the time of reception print or report
print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No transmission, 1: Transmission
Default value 0
Supplement/memo Charging management device: Coin manager, Non-Canon-made
control card
DFLT-CPY Setting of color mode for copy
Lv.1 Details To set the default color mode for copy operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: B/W
mode
Default value Europe: 2, Other than Europe: 0
Related user mode Function Settings> Copy> Select Color Settings for Copy> Use Auto
(Color/Black) Selection
8
Service Mode > COPIER > OPTION > USER
8 Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
DFLT-BOX Set of color mode for box print
Lv.1 Details To set the default color mode for box print operation.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Based on Auto/ACS/Printer Driver settings, 1: Color mode, 2: B/W
mode
Default value Europe: 2, Other than Europe: 0
Related user mode Function Settings> Copy> Select Color Settings for Copy> Use Auto
(Color/Black) Selection
DOC-REM Display/hide of original removal message
Lv.1 Details To set whether to display or hide the message to remove original when
scanning with DADF without opening/closing DADF after scanning
with the copyboard.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
DPT-ID-7 Password entry set at dept ID reg/auth
Lv.2 Details To set whether to require a password entry at the time of registration/
authentication of department ID.
With the setting to require entry, entry of 7-digit password is required
as well as entry of department ID.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Department ID only, 1: 7-digit (password) entry
Default value 0
RUI-RJT Connct set at invalid auth from remoteUI
Lv.2 Details To set to disconnect HTTP port when the machine receives invalid
authentication from remote UI 3 times.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value 0
8-144
8-144