Canon imageRUNNER ADVANCE C2030 Service Manual page 689

COPIER > OPTION > NETWORK
SP-LINK Mode setting at 1W sleep
Lv.1 Details Switch to execute 10base-T standby as default to realize the standby
power 1W in sleep mode.
Use case When shifting to sleep mode after negotiation (same as conventional
machines)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Shift to sleep mode with 10base-T
1: Shift to sleep mode after negotiation
Default value 0
LM-LEVEL Set of SMB client authentication method
Lv.1 Details To set the authentication method (LM, NTLMv1, NTLMv2) that the
SMB client uses for authentication.
In SMB authentication, authentication is generally made by
the authentication method with higher level, and if it fails, the
authentication level is lowered. (NLTMv2 => NLTMv1 => LM)
It is possible to limit the authentication level by setting 1 or 2 to avoid
using the authentication method with lower level.
Use case Upon user's request
Display/adj/set range 0 to 2
0: Authentication is made by LM, NTLMv1 and NTLMv2
1: Authentication is made by NTLMv1 and NTLMv2
2: Authentication is made by NTLMv2
Default value 0
Supplement/memo Windows NT LAN Manager authentication: A user authentication
method for network logon, which was generally used in the OS for
Windows NT Series prior to Windows NT 4.0
AFS-JOB Set of FAX server job reception port
Lv.1 Details To set the reception port of the fax server to which a fax client sends
jobs.
Use case When changing the job reception port of the fax server
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
Default value 20317
Related service mode COPIER> OPTION> NETWORK> AFC-EVNT
AFC-EVNT Set of FAX client event reception port
Lv.1 Details To set the event notification reception port of a fax client.
Use case When changing the event notification reception port of a fax client
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 65535
Default value 29400
Related service mode COPIER> OPTION> NETWORK> AFS-JOB
8
Service Mode > COPIER > OPTION > NETWORK
8 Service Mode > COPIER > OPTION > NETWORK
COPIER > OPTION > NETWORK
ILOGMODE Setting of IP address block mode
Lv.1 Details To set all protocols or TCP/UDP/ICMP unicast as the target of IP
block.
When 0 is set, the machine responds to ARP, ICMP multicast and
broadcast which have no direct relation, and consequently the number
of logs is increased.
When 1 is set, the machine filters TCP, UDP and ICMP unicast only.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 3
0: All protocols support mode
1: TCP/UDP/ICMP unicast support mode
2, 3: Not used
Default value 0
ILOGKEEP Set of IP address block log hold time
Lv.1 Details To set the retention time from the log time of IP block.
When access is made again from a same IP address which was
blocked before, if it is within the retention time of the previous log, its
log is not recorded.
If access is frequently made from a same IP address, the log record
of the UI might be filled with its logs. If the user considers that a single
log for a same IP address is enough, set the longer retention time.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 48
0: 1 minute (special mode)
1 to 48: 1 hour to 48 hours
Default value 1
IPTBROAD Set to allow broad/multi cast TX
Lv.1 Details To set whether to permit transmission of broadcast packets and
multicast packets.
Transmission of broadcast packets and multicast packets is permitted
without specifying an exception address. It is permitted within the
device even if it is rejected in the default setting of the IPv4/v6
transmission filter.
Set "1: Disabled" when the user does not want to send them.
Use case Upon user's request
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 5
0: Enabled, 1: Disabled, 2 to 5: Not used
Default value 0
8-137
8-137