Canon imageRUNNER ADVANCE C2030 Service Manual page 674

COPIER > OPTION > IMG-TR
TRDAYCNT Pry trn tgt crrnt crrct fed sht set:R&D
Lv.1 Details To set the number of sheets to be fed for executing the primary
transfer target current correction.
Set the environment for correction by TRDATENV and set the
correction value by TRDAYTGT.
Use case When density varies at the time of making a large number of outputs
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this at the normal service.
Display/adj/set range 0 to 3
0: OFF, 1: Correction for 500 sheets is executed after 500 sheets are
fed. 2: Correction for 1000 sheets is executed after 1000 sheets are
fed. 3: Both 1 and 2 are executed.
Default value 0
Related service mode COPIER> OPTION> IMG-TR> TRDATENV, TRDAYTGT
TRENVSW Pry trn ATVC tgt crrnt adj ev set: R&D
Lv.1 Details To set the environment to adjust the target current offset at the primary
transfer ATVC control.
Check the use environment from COPIER> DISPLAY> MISC> ENV-
TR.
Set the offset value from COPIER> ADJUST> HV-TR> 1TR-TGY, 1TR-
TGM, 1TR-TGC, 1TR-TGK1, 1TR-TGK4.
Use case When a ghost image due to transfer failure occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this at the normal service.
Display/adj/set range 0 to 7
0: All environments, 1: Low humidity environment, 2: Normal
environment, 3: High humidity environment, 4: Low humidity
environment + Normal humidity environment, 5: Low humidity
environment + High humidity environment, 6: Normal humidity
environment + High humidity environment, 7: OFF
Default value 0
Related service mode COPIER> DISPLAY> MISC> ENV-TR
COPIER> ADJUST> HV-TR> 1TR-TGY, 1TR-TGM, 1TR-TGC, 1TR-
TGK1, 1TR-TGK4
TRDAYTGT Pry trn tgt crrnt crrct VL adj: For R&D
Lv.1 Details To adjust the offset correction value of the primary transfer target
current correction after a specified number of sheets is fed.
Set the environment for correction by TRDATENV and set the number
of sheets to be fed by TRDAYCNT.
Use case When density varies at the time of making a large number of outputs
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this at the normal service.
Display/adj/set range -5 to 5
Unit 1 micro A
Default value 0
Related service mode COPIER> OPTION> IMG-TR> TRDATENV, TRDAYCNT
8
Service Mode > COPIER > OPTION > IMG-TR
8 Service Mode > COPIER > OPTION > IMG-TR
COPIER > OPTION > IMG-TR
T2TOPDIV Ppr lead edge V:thin ppr sprtn error
Lv.1 Details When the second side of the thin paper winds around the ITB,
sometimes a jam occurs due to the secondary transfer separation
failure.
In this case, if the value is set to either 1, 2 or 3, the voltage of the
leading edge on the second side is decreased, so the force which the
thin paper winds around the ITB gets weakened.
Use case When a jam occurs due to the separation failure on the second side of
thin paper
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Do not use this at the normal service.
Display/adj/set range 0 to 3
0: OFF, 1: Weak separation, 2: Medium separation, 3: Strong
separation
Default value 0
8-122
T-8-41
8-122