Canon imageRUNNER ADVANCE C2030 Service Manual page 637

COPIER > ADJUST > HV-TR
TR-DUP6 Sec trns indiv setting feed side: set 6
Lv.2 Details To set the feed side for setting 6.
Setting 6 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV6,
TR-PPR6, TR-CLR6 and TR-DUP6. When this condition is satisfied,
the target current that is set in 2TR-TGT6 is applied to the Secondary
Transfer Outer Roller.
Use case When an image failure that differs on the 1st/2nd side occurs (mottled
image/density loss due to excessive transfer/toner scattering on solid
image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: 1-sided, 2: Auto 2-sided, 3: Multi-purpose Tray 2-sided
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV6, TR-PPR6, TR-CLR6, 2TR-
TGT6
TR-DUP7 Sec trns indiv setting feed side: set 7
Lv.2 Details To set the feed side for setting 7.
Setting 7 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV7,
TR-PPR7, TR-CLR7 and TR-DUP7. When this condition is satisfied,
the target current that is set in 2TR-TGT7 is applied to the Secondary
Transfer Outer Roller.
Use case When an image failure that differs on the 1st/2nd side occurs (mottled
image/density loss due to excessive transfer/toner scattering on solid
image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: 1-sided, 2: Auto 2-sided, 3: Multi-purpose Tray 2-sided
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV7, TR-PPR7, TR-CLR7, 2TR-
TGT7
8
Service Mode > COPIER > ADJUST > HV-TR
8 Service Mode > COPIER > ADJUST > HV-TR
COPIER > ADJUST > HV-TR
TR-DUP8 Sec trns indiv setting feed side: set 8
Lv.2 Details To set the feed side for setting 8.
Setting 8 is the combination condition of environment, paper type
(paper weight), color mode and feed side that are set in TR-ENV8,
TR-PPR8, TR-CLR8 and TR-DUP8. When this condition is satisfied,
the target current that is set in 2TR-TGT8 is applied to the Secondary
Transfer Outer Roller.
Use case When an image failure that differs on the 1st/2nd side occurs (mottled
image/density loss due to excessive transfer/toner scattering on solid
image)
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 1 to 3
1: 1-sided, 2: Auto 2-sided, 3: Multi-purpose Tray 2-sided
Default value 1
Related service mode COPIER> ADJUST> HV-TR> TR-ENV8, TR-PPR8, TR-CLR8, 2TR-
TGT8
1TR-TGY Adj of prmry trns ATVC Y target current
Lv.2 Details To adjust the offset of the target current for Y upon primary transfer
ATVC control.
As the value is incremented by 1, the offset is increased by 1micro A.
Increase the value if spotty mark or mottled image occurs.
Decrease the value if leopard pattern image occurs.
The setting is enabled in an environment set by COPIER > OPTION
> IMG-TR > TRENVSW.
Use case When an image failure due to the primary transfer occurs
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -10 to 10
Unit 1 micro A
Default value 0
Related service mode COPIER> OPTION> IMG-TR> TRENVSW
1TR-TGM Adj of prmry trns ATVC M target current
Lv.2 Details To adjust the offset of the target current for M upon primary transfer
ATVC control.
As the value is incremented by 1, the offset is increased by 1 micro A.
Increase the value if spotty mark or mottled image occurs.
Decrease the value if leopard pattern image occurs.
The setting is enabled in an environment set by COPIER > OPTION
> IMG-TR > TRENVSW.
Use case When an image failure due to the primary transfer occurs
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -10 to 10
Unit 1 micro A
Default value 0
Related service mode COPIER> OPTION> IMG-TR> TRENVSW
8-85
8-85