Canon imageRUNNER ADVANCE C2030 Service Manual page 479

E Detail Location Item
Code Code
E001 0005 05 Title Center Thermistor high temperature detection
Detection Main Thermistor 1 hardware signal is continued for 1 sec or
longer.
Remedy Fixing Assembly error, Fixing temperature detection error
1. Check failure between the DC Controller PCB (UN09/ J12) and
the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable,
open circuit, connector disconnection).
-> Replace the part in the case of trapped cable/open circuit
2. Disconnect the connector of DC Controller PCB (UN09/ J12)
and start the host machine to check the reading value of the
following: service mode > COPIER > DISPLAY > ANALOG >
FIX-E
=> When the value is 40 deg C or higher
3-1. Replace the DC Controller PCB (UN09)
=> When the value is lower than 40 deg C
3-2. Replace the Fixing Assembly
NOTE: After performing the above remedy work, go through the
following to clear the error: COPIER > FUNCTION > CLEAR >
ERR
E001 0006 05 Title Edge Thermistor high temperature detection
Detection Sub Thermistor 1 hardware error detection signal is continued for
1 sec or longer.
Remedy Fixing Assembly error, Fixing temperature detection error
1. Check failure between the DC Controller PCB (UN09/ J12) and
the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable,
open circuit, connector disconnection).
-> Replace the part in the case of trapped cable/open circuit
2. Disconnect the connector of DC Controller PCB (UN09/ J12)
and start the host machine to check the reading value of the
following: service mode > COPIER > DISPLAY > ANALOG >
FIX-E2
=> When the value is 40 deg C or higher
3-1. Replace the DC Controller PCB (UN09)
=> When the value is lower than 40 deg C
3-2. Replace the Fixing Assembly
NOTE: After performing the above remedy work, go through the
following to clear the error: COPIER > FUNCTION > CLEAR >
ERR
7
Error Code > Error Code > Error Code Details
Description
7 Error Code > Error Code > Error Code Details
E Detail Location Item
Code Code
E001 0007 05 Title Edge Thermistor high temperature detection
Detection Sub Thermistor 2 hardware error detection signal is continued for
1 sec or longer.
Remedy Fixing Assembly error, Fixing temperature detection error
1. Check failure between the DC Controller PCB (UN09/ J12) and
the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable,
open circuit, connector disconnection).
-> Replace the part in the case of trapped cable/open circuit
2. Disconnect the connector of DC Controller PCB (UN09/ J12)
and start the host machine to check the reading value of the
following: service mode > COPIER > DISPLAY > ANALOG >
FIX-C
Check the reading value of the following: service mode > COPIER
> DISPLAY > ANALOG > FIX-E3
=> When the value is 40 deg C or higher
3-1. Replace the DC Controller PCB (UN09)
=> When the value is lower than 40 deg C
3-2. Replace the Fixing Assembly
NOTE: After performing the above remedy work, go through the
following to clear the error: COPIER > FUNCTION > CLEAR >
ERR
E001 0008 05 Title Displacement detection
Detection The temperature difference between the Sub Thermistor 1 (TH3)
and the Sub Thermistor 2 (TH4) remained 45 deg C or more for 1
second or more.
Remedy Fixing Assembly error, Fixing temperature detection error
1. Check failure between the DC Controller PCB (UN09/ J12) and
the Fixing Assembly (UN37/ J123, UN13/ J13) (trapped cable,
open circuit, connector disconnection).
-> Replace the part in the case of trapped cable/open circuit
2. Disconnect the connector of DC Controller PCB (UN09/ J12)
and start the host machine to check the reading value of the
following: service mode > COPIER > DISPLAY > ANALOG > FIX-
E2,FIX-E3
=> When the value of either one is 40 deg C or higher
3-1. Replace the DC Controller PCB (UN09)
=> When the both values are lower than 40 deg C
3-2. Replace the Fixing Assembly
NOTE: After performing the above remedy work, go through the
following to clear the error: COPIER > FUNCTION > CLEAR >
ERR
7-5
Description
7-5