Page 1 ND 7000 Operating Instructions Milling Digital Readout English (en) 01/2020...
Page 2: Table Of Contents
13 Programming (software option)....................211 14 File management..........................225 15 Settings............................233 16 Servicing and maintenance......................279 17 What to do if ..........................287 18 Removal and disposal........................291 19 Specifications..........................293 20 Index...............................301 21 List of figures..........................304 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 3 Intended use............................28 Improper use............................28 Personnel qualification........................29 Obligations of the operating company....................29 General safety precautions......................... 30 2.7 .1 Symbols on the product......................30 2.7 .2 Electrical safety precautions....................31 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 4 Device overview........................... 47 Connecting encoders........................... 50 Connecting touch probes........................51 Wiring switching inputs and outputs....................52 Connecting a printer..........................55 Connecting input devices........................55 Connecting a network peripheral.......................56 5.10 Connecting the line voltage........................57 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 5 Operating elements of the position display................80 6.9.2 Position display functions......................81 6.10 Status bar............................. 82 6.10.1 Operating elements of the status bar..................82 6.10.2 Adjusting settings in the quick access menu................83 6.10.3 Stopwatch..........................84 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 6 Adjusting the display......................120 7 .4.5 Defining error messages....................... 120 7 .4.6 Backing up and restoring OEM settings................124 7 .4.7 Configuring the unit for screenshots..................125 Back up settings..........................126 Back up user files..........................127 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 7 Performing the reference mark search after startup............. 131 8.2.3 Setting the language......................131 8.2.4 Changing the password......................132 Single steps for setup........................133 8.3.1 Basic settings.........................133 8.3.2 Preparing machining processes..................... 147 Back up settings..........................154 Back up user files..........................155 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 8 9.10.3 Programming the row of holes..................... 172 9.10.4 Simulating program run......................173 9.11 Machining a row of holes (program run)..................173 9.11.1 Opening a program........................174 9.11.2 Running a program........................ 174 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 9 Machining patterns.........................192 11.3 Executing blocks..........................197 11.4 Using the simulation window......................198 11.4.1 Depiction as contour view.....................199 11.5 Working with the positioning aid....................200 11.6 Applying the Scaling factor......................200 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 10 Closing a program........................223 13.5.3 Saving a program........................223 13.5.4 Saving a program under a new name................... 224 13.5.5 Saving a program automatically.....................224 13.5.6 Deleting a program........................ 224 13.6 Editing program blocks........................224 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 11 Contents 14 File management..........................225 14.1 Overview............................. 226 14.2 File types.............................227 14.3 Managing folders and files....................... 227 14.4 Viewing files............................230 14.5 Exporting files............................ 231 14.6 Importing files............................ 232 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 12 Switching functions........................253 15.6.5 Inputs (Switching functions)....................254 15.6.6 Outputs (Switching functions)....................254 15.6.7 Adding M functions....................... 255 15.6.8 Configuring M functions......................255 15.6.9 <Axis name> (settings of the axis)..................256 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 13 15.7 .16 Configuring M functions......................276 15.7 .17 Text database......................... 276 15.7 .18 Messages..........................277 15.7 .19 Back up and restore (OEM area)................... 277 15.7 .20 Documentation........................278 15.7 .21 Software options........................278 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 14 19.3 Product dimensions and mating dimensions................. 296 19.3.1 Product dimensions with Single-Pos stand................298 19.3.2 Product dimensions with Duo-Pos stand................299 19.3.3 Product dimensions with Multi-Pos stand................299 19.3.4 Product dimensions with Multi-Pos holder................300 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 15 Contents 20 Index...............................301 21 List of figures..........................304 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 17: Fundamentals
Fundamentals...
Page 18 Part number (ID) Demo software for the product ND 7000 Demo is software you can install on a computer regardless of the device. ND 7000 Demo helps you to become familiar with, try out or present the functions of the device.
Page 19 If the ID numbers and indexes do not match, so that the documentation is not valid, you will find the current documentation for the product at www.heidenhain.de. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 20 Have you found any errors or would you like to suggest changes? We continuously strive to improve our documentation for you. Please help us by sending your suggestions to the following e-mail address: userdoc@heidenhain.de HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 21 These instructions must be read and observed by every person who performs any of the following tasks: Mounting Installation Commissioning and configuration Operation Programming Service, cleaning and maintenance Troubleshooting Removal and disposal HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 22 ... items supplied with the product ... accessories for the product ✓ ✓ ... correct mounting of the product 4 "Mounting" ✓ ✓ ... correct installation of the product 5 "Installation" HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 23 ✓ ✓ ✓ 19 "Specifications" ... product dimensions and mating dimensions (drawings) This chapter enables accessing the content of these ✓ ✓ ✓ 20 "Index" instructions according to specific topics. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 24 The behavior of the functions depends on the configurable machine settings The book symbol represents a cross reference to external documentation, e.g. the documentation of your machine tool builder or other supplier. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 25 Identifies an item of a list Example: TTL interface EnDat interface Bold Identifies menus, displays and buttons Example: Tap Shut down The operating system shuts down Turn the power switch off HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 27: Safety
Safety...
Page 28 The products of the ND 7000 series are advanced digital readouts for use on manually operated machine tools. In combination with linear and angle encoders, digital readouts of the ND 7000 series return the position of the tool in more than one axis and provide further functions for operating the machine tool.
Page 29 Provide all materials and means necessary in order for the personnel to complete the assigned tasks Ensure that the device is operated only when in perfect technical condition Ensure that the device is protected from unauthorized use HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 30 Functional ground connection as per IEC/EN 60204-1. Observe the information on installation. Product seal. Breaking or removing the product seal will result in forfeiture of warranty and guarantee. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 31 If you open the product, the warranty and the guarantee will become void. Never open the housing Only the product manufacturer is permitted to access the inside of the product HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 33: Transport And Storage
Transport and storage...
Page 34: Overview
Installation Instructions Printed issue of the Installation Instructions in the currently available languages Single-Pos stand Stand for rigid mounting, inclination angle 20°, fixing hole pattern 50 mm x 50 mm HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 35: Accessories
50 mm x 50 mm Multi-Pos holder Holder for fastening the 1089230-08 device on an arm, continu- ously tiltable within an angle of 90°, fixing hole pattern 50 mm x 50 mm HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 36: In Case Of Damage In Transit
"Storage and distribution of the documentation", Page 21 Further information: If the device is returned for repair to the Service Department: Ship the device without accessories, without encoders and without peripherals HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 37: Storage Of The Product
Storage of the product Package the product as described above Observe the specified ambient conditions Further information: "Specifications", Page 293 Inspect the product for damage after any transport or longer storage times HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 39: Mounting
Mounting...
Page 40: Overview
Allen key, size 2.5 (Duo-Pos stand) Materials for mounting on a supporting surface The unit must be mounted to a stand or a holder to ensure the correct and intended use of the product. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 41: Mounting On Single-Pos Stand
Figure 2: Product mounted on Single-Pos Figure 3: Cable routing on Single-Pos stand stand "Product dimensions with Single-Pos stand", Page 298 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 42: Mounting On Duo-Pos Stand
Figure 4: Product mounted on Duo-Pos stand Figure 5: Cable routing on Duo-Pos stand "Product dimensions with Duo-Pos stand", Page 299 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 43: Mounting On Multi-Pos Stand
Figure 6: Product mounted on Multi-Pos stand Figure 7: Cable routing on Multi-Pos stand Further information: "Product dimensions with Multi-Pos stand", Page 299 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 44: Mounting On Multi-Pos Holder
Figure 8: Product mounted on Multi-Pos Figure 9: Cable routing on Multi-Pos holder holder Further information: "Product dimensions with Multi-Pos holder", Page 300 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 45: Installation
Installation...
Page 46: Overview
(ESD). It is essential to observe the safety precautions for handling ESD-sensitive components Never touch connector pins without ensuring proper grounding Wear a grounded ESD wristband when handling device connections HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 47: Device Overview
If you remove a measuring device or peripheral, re-attach the dust protection cap to the connection The type of connections for encoders may vary depending on the product version. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 48: Figure 10: Rear Panel On Devices With Id 1089178-Xx
Rear panel without dust protection caps HEIDENHAIN X113 X100 AC 100 V ... 240 V 50 Hz ... 60 Hz (max. 38 W) X116 Figure 10: Rear panel on devices with ID 1089178-xx HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 49: Figure 11: Rear Panel On Devices With Id 1089179-Xx
X116: RJ45 Ethernet connection for communication and data exchange with subse- quent systems or PC X113: 15-pin D sub connection for touch probes (e.g., HEIDENHAIN touch probe) X100: Power switch and power connection Additional connections on devices with ID 1089179-xx: X105: 37-pin D-sub connection for digital interface (DC 24 V;...
Page 50: Connecting Encoders
If the cable connectors include mounting screws, do not overtighten them Pin layout of X1, X2, X3 11 µA EnDat 2.2 R– 11 μA Inter- EnDat DATA shield CLOCK A– Sense B– Sense 11 μA 1– 2– DATA CLOCK EnDat HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 51: Connecting Touch Probes
B – Probe signals, readiness TP – Touch Probe, normally closed Digital inputs: Digital outputs: X113 X113 Din 0...3 DC 5 V DC 5 V Dout 0 Touch probe: X113 DC 5 V HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 52: Wiring Switching Inputs And Outputs
The digital or analog inputs and outputs must be assigned in the device settings of the respective switching function. Pin layout of X104 CO – Change Over NO – Normally Open NC – Normally Closed Relay outputs: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 53 Dout 1 Dout 3 Dout 5 Dout 7 DC 24 V Digital inputs: Digital outputs: X105 X105 Pin 17, 18, 36 Din 0...23 DC 24 V DC 24 V Dout 0...7 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 54 B – Probe signals, readiness TP – Touch Probe, normally closed Digital inputs: Digital outputs: X113 X113 Din 0...3 DC 5 V DC 5 V Dout 0 Touch probe: X113 DC 5 V HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 55: Connecting A Printer
"Assembly of the product", Page 40 Connect USB mouse or USB keyboard to USB Type-A port (X32). Make sure the USB cable connector is fully inserted Further information: "Device overview", Page 47 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 56: Connecting A Network Peripheral
The cable connector must firmly engage in the port Further information: "Device overview", Page 47 Pin layout of X116 1 2 3 4 5 6 7 8 D3– D2– D4– (TX+) (TX-) (RX+) (RX–) HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 57: Connecting The Line Voltage
Comply with the pin layout Connect the power connection to a 3-wire grounded power outlet using a power cable that meets requirements Further information: "Device overview", Page 47 Pin layout X100 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 59: Basic Operation
Basic operation...
Page 60: Overview
The following overview describes the different gestures for operating the touchscreen or the mouse: Tapping Means touching the screen briefly with your fingertip Means pressing the left mouse button once HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 61 Means pressing the left mouse button once and holding it down while moving the mouse; at least the starting point of the motion is defined The actions initiated by dragging include Scrolling through lists and texts HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 62: General Operating Elements And Functions
Tap + or – until the desired value is displayed Long-press + or – to scroll through the values more quickly The selected value is displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 63 The last action is undone To add a feature, tap Add The new feature is added Close Tap Close to close a dialog Confirm Tap Confirm to conclude an activity HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 64: Nd 7000 - Switch-On And Switch-Off
Tap anywhere on the touchscreen An arrow appears at the bottom of the screen Drag the arrow up The screen is switched on and shows the user interface last displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 65: Switching Off The Nd 7000
Before a new user can log in, the logged-in user has to log out. The product provides various authorization levels that grant the user full or restricted access to management and operation functionality. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 66: User Login
Tap Log out The user is logged out All functions of the main menu are inactive, except for Switch The product can only be used again after a user has logged in HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 67: Setting The Language
"Activating the reference mark search", Page 101 User interface The unit is available in different versions, which are variously equipped. The user interface and available functions may vary depending on the version. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 68: User Interface After Switch-On
"Manual operation menu", Page 71 Further information: If automatic user login is not activated, then the product opens the User login menu. Further information: "User login menu", Page 78 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 69: Main Menu Of The User Interface
Execution of a previously created program with user inter- face "Program run menu (software Further information: option)", Page 74 Programming (software option) Creation and management of individual programs Further information: "Programming menu (software option)", Page 75 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 70 Shutdown of the operating system or activation of power- saving mode Further information: "Switch-off menu", Page 80 Selecting grouped operating elements When Software-Option ND 7000 PGM is activated, the following operating elements are grouped in the main menu: MDI mode Program run Programming You can identify grouped operating elements by an arrow.
Page 71: Manual Operation Menu
Spindle speed (machine tool) In the Manual operation menu, the workspace shows the position values measured at the machine axes. The status bar provides auxiliary functions. Further information: "Manual operation", Page 175 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 72: Mdi Menu
Further information: "Selecting grouped operating elements", Page 70 The user interface for MDI mode is displayed Figure 16: MDI menu Axis key Actual position Distance-to-go Status bar Spindle speed (machine tool) HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 73: Figure 17: Mdi Block Dialog Box
You specify the distance to the target point, and the distance to go is then calculated and displayed. The status bar provides additional measured values and functions. Further information: "MDI mode", Page 189 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 74: Program Run Menu (Software Option)
Program run menu, you can display a simulation window that visualizes the selected block. The status bar provides additional measured values and functions. "Program run (software option)", Page 203 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 75: Programming Menu (Software Option)
The status bar and the optional OEM bar are not available in the Programming menu. You can see a visualization of the selected block in the optional simulation window. Figure 19: Programming menu View bar Toolbar Program management HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 76: Figure 20: Programming Menu With Opened Simulation Window
In the Programming menu, you can create and manage programs. You define individual machining steps or machining patterns as blocks. A sequence of blocks then forms a program. Further information: "Programming (software option)", Page 211 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 77: File Management Menu
The USB mass storage products and the network drives are displayed with their name or drive designation. Further information: "File management", Page 225 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 78: User Login Menu
To log in another user, the logged-in user must first log out. "User login and logout", Page 65 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 79: Settings Menu
Further information: "Settings", Page 233 The product provides various authorization levels that grant the user full or restricted access to management and operation functionality. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 80: Switch-Off Menu
Reference mark search performed successfully Reference mark search not performed or no reference mark detected Selected gear stage of the gear spindle Further information: "Setting the gear stage for gear spindles", Page 82 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 81: Position Display Functions
Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 82: Status Bar
6.10.1 Operating elements of the status bar The status bar provides the following operating elements: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 83: Adjusting Settings In The Quick Access Menu
Unit for linear values (Millimeters or Inch) Unit for angular values (Radian, Decimal degrees or Deg-Min-Sec) The Scaling factor by which the stored position is multiplied during execution of an MDI block or program block HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 84: Stopwatch
Operating element Function Start Starts time measurement or resumes time measure- ment after Pause Pause Interrupts time measurement Stop Stops time measurement and resets it to 0:00:00 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 85: Calculator
The status bar and the optional OEM bar are not available in the Programming menu. The optional OEM bar allows you to control the configuration of the functions of the connected machine tool, independently of its configuration. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 86: Operating Elements Of The Oem Bar
Press and hold the desired Spindle speed field on the OEM The background color of the field is highlighted in green The product applies the current spindle speed as the nominal value and displays it in the Spindle speed field HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 87: Messages And Audio Feedback
To make the message display area smaller, drag the handle To close the display area, drag the handle up out of the screen The number of unclosed messages is indicated in Messages HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 88: Wizard
The wizard proceeds to the next step or completes the process Tap Next to proceed to the next step Tap Back to return to the previous step Tap Close to close the wizard HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 89: Audio Feedback
The available sounds are grouped into categories. The sounds differ within a category. You can define the audio feedback settings in the Settings menu. Further information: "Sounds", Page 238 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 91: Commissioning
Commissioning...
Page 92: Overview
If the password is no longer known, contact a HEIDENHAIN service agency. Confirm the entry with RET Tap Log in The user is logged in The product opens the Manual operation mode HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 93: Performing The Reference Mark Search After Startup
The language selected for the user is indicated by a national flag in the Language drop-down list Select the flag for the desired language from the Language drop-down list The user interface is displayed in the selected language HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 94: Changing The Password
Page 92). Basic settings Selecting the Application Activating the Software options Setting the date and time Setting the units of measure Configuring a touch probe Configuring a touch probe HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 95 If the product is disconnected from the power source while it is on, the configuration data can be lost or corrupted. Back up the configuration data and keep the backup for recovery purposes HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 96: Basic Settings
Contact a HEIDENHAIN service agency and submit the displayed device information in order to request a license key for the product The license key and the license file are generated and sent by e-mail HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 97 Activating a license key You can activate a license key by Reading the license key from the provided license file into the product Entering the license key manually into the product HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 98 On the overview page, you can check which Software options are enabled for the product. Tap Settings in the main menu Tap Service Open in the sequence Software options Overview A list of enabled Software options is displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 99 To set the rounding method, tap the corresponding drop- down list and select the rounding method To set the number of decimal places displayed, tap – or + Further information: "Units", Page 241 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 100: Configuring A Touch Probe
7.3.2 Configuring a touch probe You can use probing functions to set presets with a HEIDENHAIN KT 130 Edge Finder. The stylus of the edge finder can be additionally fitted with a ruby ball tip. In order to use the KT 130 edge finder, you need to configure the relevant parameters.
Page 101 The functions of the product will only be available after the reference mark search has been completed The Reference symbol stops blinking upon successful completion of the reference mark search Further information: "Operating elements of the position display", Page 80 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 102 To view the electronic ID label of the encoder, tap ID label In order to see the results of the encoder diagnosis, tap Diagnosis Further information: "<Axis name> (settings of the axis)", Page 256 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 103 Select the reference mark from the Reference mark drop- down list: None: There is no reference mark One: The encoder has one reference mark Coded: The encoder has distance-coded reference marks HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 104 Positive: The direction of traverse is in the counting direction of the encoder Negative: The direction of traverse is opposite to the counting direction of the encoder Further information: "<Axis name> (settings of the axis)", Page 256 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 105 Commissioning | Steps for commissioning Overview of typical encoders The following overview lists the parameters of the HEIDENHAIN encoders that are typically connected to the product. When connecting other encoders, refer to the encoder's documentation for the required parameters. Linear encoders...
Page 106 If applicable, enter the corresponding values in the Maximum spindle speed for oriented spindle stop and Maximum spindle speed for thread cutting fields Further information: "Spindle axis S", Page 263 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 107 Linear error compensation and segmented linear error compensation cannot be combined with each other. If you enable a reference point shift, then you need to reconfigure the error compensation. This helps you avoid measuring errors. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 108 Use the ON/OFF slider to activate the Compensation function You can also use Linear error compensation (LEC) for angle encoders if the rotation angle is less than 360°. Further information: "Linear error compensation (LEC)", Page 261 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 109 To switch to the previous display, tap Back twice Use the ON/OFF slider to activate the Compensation function The error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 262 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 110 To switch to the previous display, tap Back Use the ON/OFF slider to activate the Compensation function The adjusted error compensation for the axis is applied Further information: "Segmented linear error compensation (SLEC)", Page 262 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 111 The ascertained line count remains stored if you select a different display mode after the teach sequence. "Settings for encoders with interfaces of the type 1 V Further information: 11 A ", Page 257 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 112: Configuring M Functions
Number range definable from M100 to M120 Function depends on the machine manufacturer Use in the button of the OEM bar Further information: "Configuring the OEM bar", Page 115 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 113: Oem Area
Tap the file name Tap Select The file is copied to the product’s Service info area "Service info", Page 242 Further information: Confirm the successful transfer with OK "Documentation", Page 278 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 114: Adding A Startup Screen
Tap the file name Tap Select The graphic file is copied to the product and displayed as the startup screen the next time the product is started Confirm the successful transfer with OK HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 115: Configuring The Oem Bar
Configuring the OEM logo You can display an OEM-specific company logo on the OEM bar. By tapping the OEM logo, you can optionally open a PDF file of the OEM documentation. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 116 Tap Spindle speed in the Type drop-down list Tap the name of the spindle in the Spindle drop-down list Enter the desired nominal value into the Spindle speed input field HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 117 For every M function, you can also define corresponding images for displaying the status using Select image for active function and Select image for inactive function Further information: "OEM bar item: M function", Page 273 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 118 For each special function, you can also define corresponding images for displaying the status using Select image for active function and Select image for inactive function Further information: "OEM bar item: Special functions", Page 274 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 119 Open in the sequence OEM area OEM bar Bar items Tap the desired menu item Tap Remove bar entry Tap OK to confirm deletion The menu item is deleted from the OEM bar HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 120: Adjusting The Display
As an OEM, you can define specific error messages that overwrite standard error messages or are triggered by defined input signals as additional messages. For this purpose, you can create a text database that contains your specific error messages. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 121: Figure 26: Example - Xml File For Text Database
Figure 26: Example – XML file for text database Then you import the XML file by means of a USB mass storage device (FAT32 format) into the product and save it, for example, to the Internal/Oem storage location. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 122 Navigate to the folder containing the XML file Tap the file name Tap Select Confirm the successful transfer with OK You have now successfully imported the Text database Further information: "Text database", Page 276 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 123 Tap Settings in the main menu Tap Service Open in the sequence OEM area Settings Messages Tap the desired message entry Tap Remove the entry Tap OK to confirm deletion The error message is deleted HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 124: Backing Up And Restoring Oem Settings
If required, connect a USB mass storage device (FAT32 format) to a USB port of the product Navigate to the folder containing the backup file Select the backup file Tap Select Confirm the successful transfer with OK HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 125: Configuring The Unit For Screenshots
For a detailed description, please refer to the ND 7000 Demo User's Manual. This User's Manual is available in the "Documentation" folder of the product website. Further information: "Demo software for the product", Page 18 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 126: Back Up Settings
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 127: Back Up User Files
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 129: Setup
Setup...
Page 130: Overview
Setup user or OEM user for the assigned password. If the password is no longer known, contact a HEIDENHAIN service agency. Confirm the entry with RET Tap Log in HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 131: Performing The Reference Mark Search After Startup
The language selected for the user is indicated by a national flag in the Language drop-down list Select the flag for the desired language from the Language drop-down list The user interface is displayed in the selected language HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 132: Changing The Password
Enter the new password and repeat it Confirm entry with RET Tap OK Close the message with OK The new password is available the next time the user logs in HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 133: Single Steps For Setup
Back up the configuration data and keep the backup for recovery purposes 8.3.1 Basic settings The commissioning engineer (OEM) may have already carried out several basic settings. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 134 To set the number of decimal places displayed, tap – or + Further information: "Units", Page 241 Entering and configuring users The following user types, which have different rights, are defined in the product's factory default settings: Setup Operator HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 135 Tap OK A message appears Close the message with OK The user is created with the basic data. The user can then further edit the data himself later HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 136 Close the message with OK To change the language, select the flag for the desired language in the Language drop-down list Use the ON/OFF slider to activate or deactivate the Auto login function HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 137 The Operating Instructions are copied to the product Any existing Operating Instructions will be overwritten Confirm the successful transfer with OK The Operating Instructions can be opened and displayed on the product HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 138 Enter the Preferred DNS server and, if required, the Alternative DNS server Confirm the entires with RET The configuration of the network connection is applied "Network", Page 244 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 139 If this list contains the used printer, the appropriate driver is available on the product and you can directly configure the printer. If this is not the case, you will need a printer-specific PPD file. "Finding PPD files", Page 143 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 140 If the appropriate driver is not listed, a suitable PPD file must be copied to the product. Further information: "Finding PPD files", Page 143 The driver is activated Tap Close in the message HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 141 Use the CUPS web interface to configure the enhanced settings of the connected printer. You can also use this web interface if the printer information fails over the product. Further information: "Using CUPS", Page 144 Further information: "Printers", Page 239 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 142 "Finding PPD files", Page 143 Further information: The driver is activated Tap Close in the message Tap Set standard values Tap Resolution to set the printer resolution HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 143 Select the PPD file Tap Select The PPD file is copied to the product Tap Continue The PPD file is loaded and the driver is activated Tap Close in the message HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 144 (e.g. http://10.6.225.86:631) In the web interface, click on the Administration tab and select the desired action See the Online Help tab for detailed information about the CUPS web interface. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 145 The model, location and connection of the printer are displayed Tap Remove Confirm with OK The printer is removed from the list and can no longer be used HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 146 Tap Input devices Select the flag for the desired language from the USB keyboard layout drop-down list The keyboard assignment corresponds to the selected language Further information: "Input devices", Page 238 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 147: Preparing Machining Processes
You can define the following parameters: Description Parameter Tool type Diameter D Length L Designation that uniquely Diameter of the tool Tool length along the identifies the tool contact surface tool axis HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 148 The symbol changes and the entry is unlocked Tap Delete A message appears Close the message with OK The selected tool is deleted from the tool table Tap Close The Tool table dialog box is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 149: Figure 29: Preset Table With Absolute Positions
Numerical You must manually enter the numeric value of the preset in the input preset table Depending on the application, users of the type Operator define the presets. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 150 (hole or cylinder) (three probing procedures with tool, four probing procedures with edge finder) In the Manual operation chapter, you can find various examples for how you can probe a preset. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 151 Leave the input field empty to load the measured value To define a new value, enter the desired value Confirm the entry with RET Tap Confirm in the wizard The new coordinates are applied as the preset HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 152 To protect the entry for a preset from accidental changes or deletion, tap the Lock symbol next to the preset's entry The symbol changes and the entry is locked Tap Close The Preset table dialog box is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 153 The active checkbox is highlighted in green Tap Delete A message appears Close the message with OK The selected preset(s) is/are deleted from the preset table Tap Close The Preset table dialog is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 154: Back Up Settings
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 155: Back Up User Files
Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 157: Quick Start
Quick Start...
Page 158: Figure 30: Example Workpiece
"Program run (software option)". Make sure that you have read and understood the "Basic operation" chapter before carrying out the actions described below. Further information: "Basic operation", Page 59 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 159 Setup user or OEM user for the assigned password. If the password is no longer known, contact a HEIDENHAIN service agency. Confirm entry with RET Tap Log in HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 160: Figure 31: Example Workpiece- Technical Drawing
A spindle axis is configured (only for the product with ID 1089179-xx) The axes have been homed Further information: "Conducting the reference mark search", Page 177 A HEIDENHAINKT 130 Edge Finder is available HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 161 The defined Ø 5.0 mm drill is added to the tool table Repeat this procedure for the other tools, and use the naming convention [Type] [Diameter] Tap Close The Tool table dialog box is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 162: Figure 32: Example Workpiece - Finding Preset D1
RET Tap Confirm in the wizard The probed coordinate is loaded in preset 0 Repeat the procedure and define the preset in the Y direction via probing HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 163: Figure 33: Example Workpiece - Drilling A Through Hole
On the machine tool move the spindles as follows: X direction: 95 mm Y direction: 50 mm Predrill the through hole and retract the spindle Keep positions X and Y You have successfully predrilled the through hole HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 164: Figure 34: Example Workpiece - Machining A Rectangular Pocket
Tap MDI in the main menu The operating element can belong to a group (based on the configuration). Further information: "Selecting grouped operating elements", Page 70 The user interface for MDI mode is displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 165 Start the machining process—follow the instructions of the wizard The product executes the individual steps of the milling operation Tap Close Program run is terminated The wizard closes You have successfully machined the rectangular pocket HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 166: Figure 35: Example Workpiece - Machining A Fit
Z coordinate: drill through Confirm each entry with RET To run the block, tap END The positioning aid is displayed If the simulation window is active, the position and traverse path are visualized HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 167: Figure 36: Example Workpiece - Finding Preset D2
To align the bolt hole circle and frame of holes you must set the circle center of the fit as the preset. Based on this preset the product then calculates all values for the relative coordinate system. Ascertain the preset with the HEIDENHAIN KT 130 Edge Finder.
Page 168 In the Set position values field, enter the value 0 for position value X and position value Y and confirm with RET Tap Confirm in the wizard The probed coordinates are loaded in preset 1 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 169: Figure 37: Example Workpiece - Drilling A Circular Hole Pattern
Tap MDI in the main menu The operating element can belong to a group (based on the configuration). Further information: "Selecting grouped operating elements", Page 70 The user interface for MDI mode is displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 170 On the product, set a spindle speed of 3500 rpm Drill the circular hole pattern and retract the spindle Tap Close Program run is terminated The wizard closes You have successfully completed the circular hole pattern HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 171: Figure 38: Example Workpiece - Programming A Bolt Hole Circle And A Row Of Holes
In Name enter the name Example Confirm the entry with RET In Unit for linear values select the mm unit of measure The program has been successfully created; you can then begin with programming HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 172 Depth: -13 Number of rows: 3 Row spacing: 45 Fill mode: bolt hole circle Confirm each entry with RET Tap Save program in the program management The program is saved HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 173: Figure 39: Example Workpiece: Simulation Window
You have defined the individual machining steps for the row of holes in a program. You can execute the created program in Program run. Figure 40: Example workpiece – drilling a row of holes HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 174 Move the axes to the next position Follow the instructions in the wizard After you have drilled the row of holes, tap Close Machining is terminated The program is reset The wizard is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 175: Manual Operation
Manual operation...
Page 176: Figure 41: Manual Operation Menu
Tap Manual operation in the main menu The user interface for manual operation is displayed Figure 41: Manual operation menu Axis key Reference Position display Status bar Spindle speed (machine tool) HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 177 Tap Reference marks Existing reference marks are cleared The Reference symbol blinks Follow the instructions of the wizard The Reference symbol stops blinking upon successful completion of the reference mark search HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 178 You can define presets on a workpiece in the Manual Operation mode in the following ways: Probe a workpiece with a HEIDENHAIN KT 130 Edge Finder. Use this method to automatically enter the presets into the preset table. Probing a workpiece with a tool (touch-off). Use this method to define the respective tool position as a datum.
Page 179 Determine the centerline of a workpiece (two probing procedures) Determine the center point of a circular form (hole or cylinder) (three probing procedures with tool, four probing procedures with edge finder) HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 180 Leave the input field empty to load the measured value To define a new value, enter the desired value Confirm the entry with RET Tap Confirm in the wizard The new coordinates are applied as the preset HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 181 Probe the edge in the Y+ direction Probe the edge in the X+ direction Probe the edge in the Z– direction The product defines the preset on the corner of the workpiece HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 182 Probe the edge in the Y+ direction Probe the edges in the X+ direction and X– direction Probe the edge in the Z– direction The products defines the preset centered on the edge of the workpiece HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 183 Probing steps Figure function Probe the hole at four points Probe the edge in the Z– direction The product defines the preset centered in the hold of workpiece HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 184 Y– direction Probe the edges in the X+ direction and X– direction Probe the edge in the Z– direction The product defines the preset in the middle of the workpiece HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 185 The entered position value is linked with the current position and overwrites the active preset in the preset table The active preset is applied as the new value Perform the desired machining operation HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 186 To protect the entry for a tool from accidental changes or deletion, tap the Lock symbol next to the tool's entry The symbol changes and the entry is locked Tap Close The Tool table dialog box is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 187 Tap the tool you want to use Tap Confirm The associated tool parameters are applied automatically The selected tool is shown on the status bar Mount the desired tool on the machine tool HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 189: Mdi Mode
MDI mode...
Page 190 "Program run (software option)", Page 203 Calling up Tap MDI in the main menu The operating element can belong to a group (based on the configuration). Further information: "Selecting grouped operating elements", Page 70 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 191: Figure 42: Mdi Menu
MDI mode | Overview Tap Create on the status bar The user interface for MDI mode is displayed Figure 42: MDI menu View bar Block parameters MDI block Status bar Block tools HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 192 Select the tool on the status bar Further information: "Creating a tool table", Page 147 You can load the current axis position with Actual position capture into the appropriate input fields. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 193: Figure 43: Schematic Depiction Of The Hole Block
Center point of the hole in the X plane Center point of the hole in the Y plane Depth Target depth for drilling in the Z plane Default: Through-hole drilling HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 194: Figure 44: Schematic Display Of The Bolt Hole Circle Block
Angle of the 1st hole of the bolt hole arc Stepping angle Angle of the circle segment Default: bolt hole circle Depth Target depth for drilling in the Z plane Default: Through-hole drilling HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 195: Figure 45: Schematic Display Of The Row Of Holes Block
Number of rows Number of rows of holes in the linear hole pattern Row spacing Spacing between the individual rows of holes Fill mode Distribution of holes All holes Frame of holes HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 196: Figure 46: Schematic Display Of The Rectangular Pocket Block
Direction in which the rectangular pocket is roughed out (clockwise or counterclockwise) Default: counterclockwise Finishing allowance Amount of material that is to be left remaining around the rectangular pocket and will be removed in the last pass HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 197 If the simulation window is activated, the current block is visualized Depending on the block, user intervention may be required; the wizard will display the relevant instructions Follow the instructions in the wizard HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 198: Figure 47: Example Of A Block In Mdi Mode
The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Position Display of parameters (position values for program run, if required) and blocks HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 199: Figure 48: Simulation Window With Contour View
Machining pattern (white) Current block or machining position (green) Tool contour, tool position and tool path (orange) Activating the simulation window Tap Graphic The simulation window for the currently selected block appears HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 200: Figure 49: Distance To Go With Position View With Graphical Positioning Aid
This enables you to mirror and scale a block. You can activate a scaling factor in the quick access menu. "Adjusting settings in the quick access menu", Page 83 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 201: Figure 50: Example - Mdi Block
Figure 51: Example – Execution of an MDI block with scaling factor If the calculated dimensions cannot be attained with the selected tool, the execution of the block is aborted. The scaling factor cannot be changed during execution of a block. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 203: Program Run (Software Option)
Program run (software option)
Page 204 The operating element belongs to a group. Further information: "Selecting grouped operating elements", Page 70 The user interface for Program Run is displayed View bar Status bar Program control Spindle speed (machine tool) Program management HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 205: Figure 52: Example Of A Program In The Program Un Operating Mode
"Managing programs", Page 210 Figure 52: Example of a program in the Program un operating mode View bar Distance-to-go display Program blocks Program control Spindle speed (machine tool) Program management HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 206 The program run cannot be aborted if the current block is executing a traverse motion. Tap Stop program in the program management The program run is aborted HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 207 You can display a visualization of the selected block in the optional simulation window. The following options are available on the view bar: Operating element Function Graphic Display of simulation and blocks Position Display of position values and blocks HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 208: Figure 53: Simulation Window With Contour View
Current block or machining position (green) Tool contour, tool position and tool path (orange) You can modify the colors and line thicknesses used in the contour view. Further information: "Simulation window", Page 237 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 209 Tap the Spindle speed input field, enter the value and tap RET to confirm The product applies the entered spindle speed as the nominal value and controls the spindle of the machine tool accordingly HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 210 Tap the folder containing the file Tap the file Tap Open The selected program is loaded 12.3.2 Closing a program Tap Close program in the program management The opened program is closed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 211: Programming (Software Option)
Programming (software option)
Page 212 Page 70 The user interface for programming is displayed View bar Toolbar Program management The status bar and the optional OEM bar are not available in the Programming menu. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 213 Negative tool radius compensation; the traverse path is R– decreased by the tool radius (inside contour) Incremental position value, i.e. the position value is referenced to the actual position Through-hole drilling without a specified position value HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 214 M function Number of the M function Optional: Selection from function table Dwell time Time interval between machining steps HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 215: Figure 54: Schematic Depiction Of The Hole Block
Center point of the hole in the X plane Center point of the hole in the Y plane Depth Target depth for drilling in the Z plane Default: Through-hole drilling HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 216: Figure 55: Schematic Display Of The Bolt Hole Circle Block
Angle of the 1st hole of the bolt hole arc Stepping angle Angle of the circle segment Default: bolt hole circle Depth Target depth for drilling in the Z plane Default: Through-hole drilling HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 217: Figure 56: Schematic Display Of The Row Of Holes Block
Number of rows Number of rows of holes in the linear hole pattern Row spacing Spacing between the individual rows of holes Fill mode Distribution of holes All holes Frame of holes HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 218: Figure 57: Schematic Display Of The Rectangular Pocket Block
Direction in which the rectangular pocket is roughed out (clockwise or counterclockwise) Default: counterclockwise Finishing allowance Amount of material that is to be left remaining around the rectangular pocket and will be removed in the last pass HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 219: Figure 58: Example Of A Program In The Programming Operating Mode
Figure 58: Example of a program in the Programming operating mode View bar Block parameters Toolbar Program blocks Program management HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 220 Define the relevant parameters, depending on the block type "Block types", Page 213 Further information: Confirm each entry with RET If the simulation window is active, the current block is visualized HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 221 The following options are available on the view bar: Control Function Graphic Display of simulation and blocks Position Display of position values and blocks HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 222: Figure 59: Simulation Window With Contour View
Tap Graphic on the view bar to enlarge the simulation window The simulation window for the highlighted block appears To leave the simulation window, tap Position in the view bar The parameter view is shown HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 223 Closing a program Tap Close program in the program management The opened program is closed 13.5.3 Saving a program Tap Save program in the program management The program is saved HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 224 The parameters of the selected block are displayed Edit the relevant parameters, depending on the block type Confirm each entry with RET Tap Save program in the program management The edited program is saved HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 225: File Management
File management...
Page 226: Figure 60: File Management Menu
Tap File management in the main menu The user interface for file management is displayed Figure 60: File management menu List of available storage locations List of folders in the selected storage location HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 227 Tap Create a new folder Tap the input field in the dialog and enter a name for the new folder Confirm entry with RET Tap OK A new folder is created HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 228 Drag the icon of the file you want to move to the rightt The operating elements are displayed Tap Move to In the dialog, select the folder to which you want to move the file Tap Select The file is moved HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 229 Drag the icon of the file you want to delete to the right The operating elements are displayed Tap Delete selection Tap Delete The folder or file is deleted HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 230: Figure 61: File Management Menu With Preview Image And File Information
Tap View The file contents are displayed Tap Close to close the view In this view, you can print PDF files on the printer configured in the product by tapping Print. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 231 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 232 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 233: Settings
Settings...
Page 234 Configuration of interfaces and network drives User Configuration of users Axes Configuration of connected encoders and error compensation Service Configuration of software options, service functions and information Activation Tap Settings in the main menu HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 235 Tap and drag: Touch the touchscreen and drag the arrow upwards from the lower edge Tap: Touch the touchscreen Tap or axis movement: Touch the touchscreen or move the axis Default setting: Tap and drag HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 236 Settings: Actual value Nominal value Default setting: Actual value Distance-to-go indicator Display of the distance-to-go indicator in MDI mode Settings: ON or OFF Default value: ON HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 237 Upward: values increase in the upward direction Downward: values increase in the downward direction Default value: Upward The Undo buttons enable the color definitions of the simulation window to be reset to factory settings. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 238 Sound to be played when using a touch element When you select a setting, the associated sound is played Settings: Standard, Guitar, Robot, Outer space, No sound Default setting: Standard HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 239 The setting range and default setting depend on the printer type Color/Black and white Specification of the printing mode The setting range and default setting depend on the printer type HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 240 Default setting: Current system time Date format Format in which the date is displayed Settings: MM-DD-YYYY: month, day, year DD-MM-YYYY: day, month, year YYYY-MM-DD: year, month, day Default setting: YYYY-MM-DD (e.g. "2016-01-31") HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 241 Round to 0 and 5: Decimal digits ≤ 24 or ≥ 75 are rounded to 0, decimal digits ≥ 25 or ≤ 74 are rounded to 5 Default setting: Commercial HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 242 Meaning and function Operating Instructions Display of the operating instructions stored on the product Default: no document; the document in the desired language can be added "Documentation", Page 278 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 243 Length offset of the edge finder Setting range: ≥ 0.0001 Default value: 0.0000 Diameter Diameter of the edge finder Setting range: ≥ 0.0001 Default value for selection of KT 130: 6.0000 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 244 IPv6 standard gateway Network address of the router connecting a network Preferred DNS server Primary server for mapping the IP address Alternative DNS server Optional server for mapping the IP address HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 245 Kerberos V5 authentication and packet signing NTLM password hashing NTLM password hashing with signing NTLMv2 password hashing NTLMv2 password hashing with signing Default value: None Configuration of the Mount options Settings: Default value: nounix,noserverino HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 246 Parameter Explanation Name Name of the switching function Switching function Selecting whether the switching function should be activated or deactivated Settings: ON or OFF Default setting: ON HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 247 (only with Interval type of switching) Upper limit Selecting the upper limit of the axis position at which switching is to occur (only Interval type of switching) Remove the entry Removing the position-dependent switching function HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 248 Language of the user – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 249 Language of the user Setup, OEM – Auto login On restart of the product: Automatic login of the last logged-in user Default value: OFF – Remove user account Removal of the user account HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 250 Path: Parameter Explanation Adds a new user of the type Operator Further information: "Entering and configuring users", Page 134 It is not possible to add further OEM and Setup-type users. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 251: Figure 62: Assignment Of The Rectangular Coordinate System To The Machine Axes
(the Z axis), the thumb points in the positive X direction, and the index finger in the positive Y direction. Figure 62: Assignment of the rectangular coordinate system to the machine axes HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 252 Start starts the reference mark search and opens the workspace Reference mark search status Indicates whether the reference mark search was successful Display: Successful Unsuccessful Stop of reference mark search Indicates whether the reference mark search was canceled Display: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 253 Further information: "Inputs (Switching functions)", Page 254 Outputs Assignment of the digital output for the respective switching function according to the pin layout Further information: "Outputs (Switching functions)", Page 254 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 254 The circuit can couple the switch-on/off of the product to the switch-on/off of the machine tool to be controlled. Default value: Not connected HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 255 Setting range: M100 ... M120 Digital output Assignment of the digital output for the M function according to pin layout Default value: Not connected Remove Removal of the selected M function HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 256 The entered required amount of time the axis to be in the positioning window positioning window so that the block will be completed Setting range: 0 ms to 10000 ms Default value: 0 ms HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 257 Settings for encoders with interfaces of the type 1 V Parameter Explanation Encoder input Assignment of the encoder input to the axis of the product Settings: Not connected Further information: "Device overview", Page 47 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 258 Frequency value of the analog low-pass filter Settings: 33 kHz: Suppression of interference frequencies above 33 kHz 400 kHz: Suppression of interference frequencies above 400 kHz Default value: 400 kHz HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 259 Settings ► Axes ► <Axis name> ► Encoder ► Reference marks Path: The reference mark search does not need to be performed for serial encoders with EnDat interface, because the axes are automatically homed. HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 260 OFF: Reference pulses are not evaluated in inverted form Default value: OFF Reference point displacement Configuration of the offset between the reference mark and the zero point Further information: "Reference point displacement", Page 261 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 261 Input: Millimeters or degrees (depending on the encoder) Actual length Input field for entering the measured length (actual distance traversed) Input: millimeters or degrees (depending on the encoder) HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 262 The start point defines the position starting from which the compensation is applied to the axis Default value: 0.00000 Create Creates a new table of supporting points based on the entries HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 263 Setting of the spindle speed that marks the transition from the upper to the lower spindle speed range curve for start-up times Setting range: 0 rpm ... 2000 rpm Default value: 1500 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 264 Assignment of the digital output for the clockwise spindle enable according to pin layout Default value: Not connected Enable spindle CCW Assignment of the digital output for the counterclockwise spindle enable according to pin layout Default value: Not connected HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 265 Spindle sleeve final position – Assignment of a digital input for the lower limit switch of the sleeves. The input is used for reversing the spindle with thread cutting. Default value: Not connected HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 266 Setting range: 0 rpm ... 2000 rpm Default value: 1500 Minimum spindle speed Definition of the minimum spindle speed Setting range: 0 rpm ... 500 rpm Default value: 50 Remove Removal of the selected gear stage HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 267 Version number of the system parameters axes.xml Version number of the axis parameters encoders.xml Version number of the encoder parameters ncParam.xml Version number of the NC parameters spindle.xml Version number of the spindle axis parameters HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 268 Restoring of user files of the product Further information: "Restore user files", Page 285 Back up user files Backing up of user files of the product Further information: "Back up user files", Page 127 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 269 Reset to shipping conditions Resetting of the settings to the factory default setting and deletion of the user files from the unit’s memory area "Reset to shipping conditions", Page 286 Further information: HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 270 Selecting the image file that is to be displayed as opening screen (file type: PNG or JPG) "Adding a startup screen", Page 114 Further information: Delete startup screen Delete clears the user-defined opening screen and restores the default view HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 271 Special functions: Further information: "OEM bar item: Special functions", Page 274 Document: Further information: "OEM bar item: Document", Page 274 Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 272 Spindle speed Setting the spindle speed Setting range: depends on the configuration of the spindle axis S Default value: 0 Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 273 Copies a selected image file to the storage location /Oem/ Images File format: PNG, JPG, PPM, BMP , or SVG Image size: Max. 100 x 70 px Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 274 Selecting the desired image for depicting the function Upload image file Copies a selected image file to the storage location /Oem/ Images Remove bar entry Removing the bar item from the OEM bar HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 275 Settings: ON or OFF Default value: OFF M functions For the configuration, see "Configuring M functions", Page 276 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 276 Select text database Selecting an XML type text database stored in the device Further information: "Creating a Text database", Page 121 Deselect text database Deselecting the currently selected text database HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 277 Page 124 Restore OEM specific folders and Restoring the settings of the OEM area as a ZIP file files Further information: " Restore OEM specific folders and files", Page 124 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 278 Activation of the software options via license key or license file Further information: "Activating a license key", Page 97 Reset trial options Reset of the trial options by entering a license key HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 279: Servicing And Maintenance
Servicing and maintenance...
Page 280 To deactivate the cleaning mode, tap anywhere on the touchscreen An arrow appears at the bottom of the screen Drag the arrow up The screen is switched on and shows the user interface last displayed HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 281 When connecting the peripheral devices (e.g. encoders), the operating company must ensure safe resumption of operation and assign authorized and appropriately qualified personnel to the task. Further information: "Obligations of the operating company", Page 29 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 282 Starting a firmware update Tap Settings in the main menu Tap Service Open in the sequence Firmware update Continue The service application is launched HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 283 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 284 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 285 Tap File management in the main menu Navigate to the list of storage locations Tap Safely remove The message The storage medium can be removed now. appears Disconnect the USB mass storage device HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 286 Tap OK to confirm shutdown of the device The product is shut down All settings are reset and the user files are deleted To restart the product, switch it off and then back on HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 287: What To Do If
What to do if ...
Page 288 17.2.1 Restoring the firmware On a computer, create the folder "heidenhain" on a USB mass storage device (FAT32 format). In the "heidenhain" folder, create the folder "update" Copy the new firmware to the "update" folder Rename the firmware "recovery.dro"...
Page 289 Contact the encoder manufacturer's service agency Axes are miscounting Incorrect settings of Check the encoder settings Qualified the encoder Page 103 personnel HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 290 User login is not possible Password does not As user with higher Qualified exist permission level, reset the personnel password Page 134 To reset the OEM password, contact the HEIDENHAIN service agency HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 291: Removal And Disposal
Removal and disposal...
Page 292 Forward the product and the backup battery to recycling in accordance with the applicable local disposal regulations If you have any questions about the disposal of the product, please contact a HEIDENHAIN service agency HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 293: Specifications
Specifications...
Page 294 Four digital inputs: TTL DC 0 V ... +5 V One digital output TTL DC 0 V ... +5 V Maximum load 1 k Ω Max. cable length with HEIDENHAIN cable 30 m HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 295 Altitude General information Directives EMC Directive 2014/30/EU Low Voltage Directive 2014/35/EU RoHS Directive 2011/65/EU Pollution degree Protection EN 60529 Front panel and side panels: IP 65 Rear panel: IP 40 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 296: Figure 63: Housing Dimensions For Productswith Id 1089178-Xx
With Multi-Pos holder: 1.85 kg 19.3 Product dimensions and mating dimensions All dimensions in the drawings are in millimeters. HEIDENHAIN 33.8 40.7±1 Figure 63: Housing dimensions for productswith ID 1089178-xx HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 297: Figure 64: Housing Dimensions For Devices With Id 1089179-Xx
AC 100 V ... 240 V 50 Hz ... 60 Hz (max. 38 W) 37 .5 15.5 X116 67 .5 Figure 65: Dimensions of the rear panel for devices with ID 1089178-xx HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 298: Figure 66: Dimensions Of The Rear Panel For Devices With Id 1089179-Xx
Figure 66: Dimensions of the rear panel for devices with ID 1089179-xx 19.3.1 Product dimensions with Single-Pos stand ISO 14581-M4x8 Md = 2.6 Nm 19.25 107±1 Figure 67: Product dimensions with Single-Pos stand HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 299: Figure 68: Product Dimensions With Duo-Pos Stand
Figure 68: Product dimensions with Duo-Pos stand 19.3.3 Product dimensions with Multi-Pos stand ISO 14581-M4x8 Md = 2.6 Nm Md = 15 Nm max. 15.25 18.75 Figure 69: Product dimensions with Multi-Pos stand HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 300: Figure 70: Product Dimensions With Multi-Pos Holder
Specifications | Product dimensions and mating dimensions 19.3.4 Product dimensions with Multi-Pos holder ISO 14581-M4x8 Md = 2.6 Nm Md = 15 Nm max. Figure 70: Product dimensions with Multi-Pos holder HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 301: Index
OEM........113 deleting........ 229 example....... 164, 166 Dragging........61 moving......... 228 Menu Duo-Pos........42 renaming......228 File management....77 Folders manual operation... 71, 176 managing......227 MDI........72 Folder structure......227 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 302 Screen keyboard....62 control blocks....... 206 adjusting the quick access slide switch......63 creating........ 219 menu........83 status bar....... 82 creating program header..220 Calculator....... 85 toggle switch......63 deleting........ 224 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 303 Programming menu....75 Program run menu....74 Settings menu....... 79 Switch-off menu..... 80 User login menu....78 User login......65, 78 Users deleting........ 137 Wiring switching inputs and outputs........52 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 304: List Of Figures
Figure 40: Figure 41: Manual operation menu....................... 176 Figure 42: MDI menu..........................191 Schematic depiction of the Hole block..................193 Figure 43: Figure 44: Schematic display of the bolt hole circle block..............194 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 305 Figure 67: Product dimensions with Single-Pos stand................298 Figure 68: Product dimensions with Duo-Pos stand................299 Figure 69: Product dimensions with Multi-Pos stand................299 Figure 70: Product dimensions with Multi-Pos holder................300 HEIDENHAIN | ND 7000 | Operating Instructions Milling | 01/2020...
Page 306 DR. JOHANNES HEIDENHAIN GmbH Dr.-Johannes-Heidenhain-Straße 5 83301 Traunreut, Germany  +49 8669 31-0  +49 8669 32-5061 E-mail: info@heidenhain.de Technical support  +49 8669 32-1000 Measuring systems  +49 8669 31-3104 E-mail: service.ms-support@heidenhain.de NC support  +49 8669 31-3101 E-mail: service.nc-support@heidenhain.de NC programming ...

HEIDENHAIN ND 7000 Operating Instructions Manual

Operating Instructions Milling

21 List of Figures

Quick Links

Chapters

Related Manuals for HEIDENHAIN ND 7000

Summary of Contents for HEIDENHAIN ND 7000

Table of Contents