Table of Contents
Advertisement
Drive/Sensor check
Motor,Solenoid
DIPSW(SW382)
1
2
3
4
5
6
7
8
-
-
-
-
-
-
-
On M9
Inlet feed motor
-
-
-
-
-
-
On -
M2
Shift feed motor
-
-
-
-
-
-
On On M3
Buffer front feed
motor
-
-
-
-
-
On -
-
M4
Buffer motor
-
-
-
-
-
On -
On M5
Delivery motor
-
-
-
-
-
On On -
M26
Processing feed
motor
-
-
-
-
-
On On On M19
Stack delivery motor After pressing ENTER to start the
-
-
-
-
On -
-
-
M18
Swing guide motor
6
Troubleshooting > Drive/Sensor check > Motor,Solenoid
Name
details
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
After pressing ENTER to start the
motor, use +/- to switch the speed.
Press ENTER again to terminate the
motor. 300 to 1500 mm/s (in units of
100 mm/s, default: 500 mm/s)
motor, use +/- to switch the speed.
Press ENTER again to terminate
the motor. 200 1500mm/s(100mm/s
default: 500mm/s)
Press ENTER to enter the mode, and
use + (Open)/-(Close). Press ENTER
to terminate the mode (Close).
6
Troubleshooting > Drive/Sensor check > Motor,Solenoid
DIPSW(SW382)
1
2
3
4
5
6
7
8
-
-
-
-
On -
On -
M9
Front alignment
motor
-
-
-
-
On -
On On M10
Rear alignment
motor
-
-
-
-
On On -
-
M17
Feed belt move
motor
-
-
-
-
On On -
On M14
Paddle rotation
motor
-
-
-
-
On On On On M15
Paddle lift motor
-
-
-
On -
-
-
-
M13
Stack delivery
auxiliary tray motor
-
-
-
On -
-
-
On M12
Assist motor
-
-
-
On -
-
On -
M16
Paper trailing edge
drop motor
-
-
-
On -
-
On On M11
Processing stopper
move motor
-
-
-
On -
On -
-
M21
Staple move motor
Name
details
After pressing ENTER to start the
motor, use +/- to move 20 mm. Press
ENTER again to terminate the motor
(Home).
After pressing ENTER to start the
motor, use +/- to move 20 mm. Press
ENTER again to terminate the motor
(Home).
After pressing ENTER to start the
motor, use + (escape position) /-
(Home). Press ENTER again to
terminate the motor (Home). The
escape position is located 36 pls from
Home.
After pressing ENTER to start the
motor, use + (2 rotations)/- (1 rotation).
Press ENTER again to terminate the
motor (Home).
After pressing ENTER to start the
motor, use + (Up)/- (Down). Press
ENTER again to terminate the motor.
It is lifted and lowered from home
position in units of 20 pls in the range
of 0 to 100 pls.
After pressing ENTER to start the
motor, the tray moves from an auxiliary
position to middle position to HP every
time ENTER is pressed. The motor is
then terminated.
After pressing ENTER to start the
motor, use + (to push paper stack)/- (to
move to Home). Press ENTER again
to terminate the motor.
After pressing ENTER to start
the motor, the motor terminates
automatically (Home).
After pressing ENTER to start the
motor, use + to move to the 1-staple
position in units of 10 mm in the range
of 0 to 50 mm. Use - to move to the
2-staple position. Press Enter again to
terminate the motor (Home).
After pressing ENTER to start the
motor, use +/- to move in units of 50
mm in the range of 60 to 400 mm.
Press ENTER again to terminate the
motor (Home).
6-3
6-3
Advertisement
Table of Contents
