Allied Telesis x510-28GTX Command Reference Manual page 775

IP A P
DDRESSING AND ROTOCOL
ARP LOG
To enable ARP logging and specify that the MAC address in the log message is
displayed in the standard IEEE format hexadecimal notation
(HH-HH-HH-HH-HH-HH), use the following commands:
awplus#
awplus(config)#
To leave ARP logging enabled, but stop using HH-HH-HH-HH-HH-HH format and
use HHHH.HHHH.HHHH format instead, use the following commands:
awplus#
awplus(config)#
To display ARP log messages, use the following command:
awplus#
Output Figure 21-1: Output from show log | include ARP_LOG after enabling ARP
awplus#configure terminal
awplus(config)#arp log
awplus(config)#exit
awplus#show log | include ARP_LOG
2016 Oct 6 06:21:01 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add 
0013.4078.3b98 (192.168.2.4)
2016 Oct 6 06:22:30 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del 
0013.4078.3b98 (192.168.2.4)
2016 Oct 6 06:23:26 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add 
0030.940e.136b (192.168.2.20)
2016 Oct 6 06:23:30 user.notice awplus IMISH[1830]: show log | include ARP_LOG
Figure 21-2: Output from show log | include ARP_LOG after enabling ARP
awplus#configure terminal
awplus(config)#arp log mac-address-format ieee
awplus(config)#exit
awplus#show log | include ARP_LOG
2016 Oct 6 06:25:28 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add
00-17-9a-b6-03-69 (192.168.2.12)
2016 Oct 6 06:25:30 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 add
00-03-37-6b-a6-a5 (192.168.2.10)
2016 Oct 6 06:26:53 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del
00-30-94-0e-13-6b (192.168.2.20)
2016 Oct 6 06:27:31 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del
00-17-9a-b6-03-69 (192.168.2.12)
2016 Oct 6 06:28:09 user.notice awplus HSL[1007]: ARP_LOG port1.0.1 vlan1 del
00-03-37-6b-a6-a5 (192.168.2.10)
2016 Oct 6 06:28:14 user.notice awplus IMISH[1830]: show log | include ARP_LOG
C613-50170-01 Rev B
C
OMMANDS
configure terminal
arp log mac-address-format ieee
configure terminal
no arp log mac-address-format ieee
show log | include ARP_LOG
logging using arp log. Note that this output uses
HHHH.HHHH.HHHH format.
logging using arp log mac-address format ieee. Note that this
output uses HH-HH-HH-HH-HH-HH format.
Command Reference for x510 Series
AlliedWare Plus™ Operating System - Version 5.4.7-1.x
775