Honda ACCORD HYBRID 2005 Service Manual page 743

17. Connect battery m o d u l e 6P connector terminal
No. 4 to body g r o u n d w i t h a j u m p e r w i r e .
B A T T E R Y M O D U L E 6P C O N N E C T O R
3 4
J U M P E R WIRE
5 6
S G T B (BLU/ORN)
W i r e side of f e m a l e t e r m i n a l s
18. Turn the ignition switch ON (II).
19. Check the BATT. MDLS TEMP S 1 , BATT. MDLS
TEMP S2, and BATT. MDLS TEMP S3 in the DATA
LIST w i t h the HDS.
Are about 4.95 V or more indicated?
Y E S — R e p l a c e the battery m o d u l e (see page
12-146), then go to step 24.
INO—Goto step 20.
20. Turn the ignition switch OFF.
2 1 . Disconnect the battery module 6P connector.
22. Disconnect M C M connector A (31P).
23. Check for continuity between M C M connector
terminal A31 and battery m o d u l e 6P connector
terminal No. 4.
MCM C O N N E C T O R A (31P)
1
2 3
4
5 6
7
8 9
1 0 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 2 0 2 1
2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1
Wire side of female t e r m i n a l s
B A T T E R Y M O D U L E 6P C O N N E C T O R
S G T B
(BLU/ORN)
1 2 3 4 5 6
S G T B (BLU/ORN)
Wire side of female t e r m i n a l s
Is there continuity?
Y E S — G o t o step 30.
NO—Repair open in the w i r e between the battery
m o d u l e and the M C M (A31), then go to step 24.
24. Turn the ignition switch OFF.
25. Reconnect all connectors.
26. Reinstall the IPU lid (see page 12-140), then t u r n the
battery m o d u l e switch ON (see page 12-4).
27. Turn the ignition switch ON (II).
28. Reset the M C M (see page 12-6).
29. Check for T e m p o r a r y DTCs or DTCs w i t h the HDS.
Are any Temporary DTCs or DTCs indicated?
Y E S — I f DTC P0A9E is indicated, check for poor
connections or loose t e r m i n a l s at the battery
m o d u l e and the M C M , then go to step 1. If any
other T e m p o r a r y DTCs or DTCs are indicated, go to
the indicated D T C s t r o u b l e s h o o t i n g .
NO—Troubleshooting is c o m p l e t e . •
30. Reinstall the IPU lid (see page 12-140), then turn the
battery m o d u l e switch ON (see page 12-4).
3 1 . Update the M C M if it does not have the latest
software, or substitute a k n o w n - g o o d M C M
(see page 12-8).
32. Check for Temporary DTCs or DTCs w i t h the HDS.
Are any Temporary DTCs or DTCs indicated?
Y E S — I f DTC P0A9E is indicated, check for poor
connections or loose terminals at the battery
m o d u l e and the M C M , then go to step 1. If any
other T e m p o r a r y DTCs or DTCs are indicated, go to
the indicated D T C s t r o u b l e s h o o t i n g .
NO—If the M C M was updated, t r o u b l e s h o o t i n g is
complete. If the M C M was substituted, replace the
original M C M (see page 1 2 - 8 ) . •
12-65