Control Mode Dependent Parameter Default Values; Control Mode Dependent Parameter Default Values; A1-02 (Motor 1 Control Mode) Dependent Parameters - YASKAWA V1000 Technical Manual

B.3 Control Mode Dependent Parameter Default Values
B.3 Control Mode Dependent Parameter Default Values
The tables below list parameters that depend on the control mode selection (A1-02 for motor 1, E3-01 for motor 2). These
parameters are initialized to the shown values if the control mode is changed.
u

A1-02 (Motor 1 Control Mode) Dependent Parameters

Table B.1 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values
Parameter
b3-02 Speed Search deactivation current
Current Control Gain during Speed Search (Speed
b3-08
Estimation Type)
b8-02 Energy Saving gain
C2-01 S-curve time at acceleration start
C3-01 Slip compensation gain
C3-02 Slip compensation time constant
C4-01 Torque compensation gain
C4-02 Torque comp. primary delay time
C6-02 Carrier frequency
E1-04 Maximum output frequency
E1-05
Maximum output voltage
E1-06 Base Frequency
E1-07 Middle output frequency
E1-08
Middle output freq. voltage
E1-09 Minimum output frequency
E1-10
Minimum output voltage
E1-11 Middle output frequency 2
E1-12
Middle output freq. voltage 2
<2>
E1-13
Base voltage
L1-01 Motor protection selection
L3-20 Main power circuit voltage adjustment gain
L3-21 Accel/decel rate calculation gain
<1> Default setting value is dependent on parameter o2-04, Drive Model Selection.
<2> Values shown here are for 200 V class drives. Double the value when using a 400 V class drive.
<3> Default setting value is dependent on parameter E5-01, Motor Code Selection.
<4> The default value is for the following localized drives: Japan (Model code: CIMR-VAoA) and Asia (Model code: CIMR-VToA)
China Localized Drive Default Values on page 381
378
Description
<2>
<2>
<2>
<2>
for the default values of China localized (Model code: CIMR-VBoA) drives.
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Setting Range Resolution
0 to 200 1%
0.00 to 6.00 –
0.0 to 10.0 0.1
0.00 to 10.00 0.01 s
0.0 to 2.5 0.1
0 to 10000 1 ms
0.00 to 2.50 0.01
0 to 10000 1 ms
1 to F 1
40.0 to 400.0 0.1 Hz
0.0 to 255.0 0.1 V
0.0 to 400.0 0.1 Hz
0.0 to 400.0 0.1 Hz
0.0 to 255.0 0.1 V
0.0 to 400.0 0.1 Hz
0.0 to 255.0 0.1 V
0.0 to 400.0 0.1 Hz
0.0 to 255.0 0.1 V
0.0 to 255.0 0.1 V
0 to 4 –
0.00 to 5.00 0.01
0.00 to 200.00 0.01
Control Modes (A1-02)
V/f (0) OLV (2) PM (5)
120 100
<1> <1>
0.30
0.50 0.50
– 0.7
0.20 0.20 1.00
0.0 1.0
2000 200
1.00 1.00 0.00
200 20
7 7
<1> <1>
60.0 60.0
<4> <4>
200.0 200.0
60.0 60.0
<4> <4>
3.0 3.0
<4> <4>
16.0 12.0
1.5 0.5
<4> <4>
12.0 2.5
0.0 0.0
0.0 0.0
0.0 0.0
1 1
1.00 0.30 0.65
1.00 1.00 2.50
.Refer to
–
–
–
–
100
2
<3>
<3>
<3>
–
–
<3>
–
–
–
–
4