YASKAWA V1000 Technical Manual page 352

B.2 Parameter Table
H1-oo
Function
Setting
62 External Search Command 2
65 KEB Ride-Thru 1 (N.C.)
66 KEB Ride-Thru 1 (N.O.)
67 Communications Test Mode
68 High-Slip Braking
6A Drive Enable
75 Up 2 Command
76 Down 2 Command
7A KEB Ride-Thru 2 (N.C.)
7B KEB Ride-Thru 2 (N.O.)
7C Short-Circuit Braking (N.O.)
7D Short-Circuit Braking (N.C.)
7E Forward/Reverse Detection
90 to 96 DWEZ Digital Inputs 1 to 7
9F DriveWorksEZ enable
<1> Available in drive software versions PRG: 1016 and later.
No. Name
Terminal MA, MB and MC Function
H2-01
Selection (relay)
Terminal P1 Function Selection (open-
H2-02
collector)
Terminal P2 Function Selection (open-
H2-03
collector)
H2-06 Watt Hour Output Unit Selection
<1> The availability of certain functions depends on the control method used.
352
H1 Multi-Function Digital Input Selections
Closed: Activates Current Detection Speed Search from the frequency
reference b3-01 = 0. Activates Speed Estimation Type Speed search if
b3-01 = 0.
Open: KEB Ride-Thru 1 enabled
Closed: Normal operation
Open: Normal operation
Closed: KEB Ride-Thru 1 enabled
Tests the MEMOBUS/Modbus RS-485/422 interface.
Closed: High-Slip braking is executed. Drive stops.
Open: Drive disabled.
If this input is opened during run, then the drive will stop as specified by
parameter b1-03.
Closed: Ready for operation.
Open: Maintains the current frequency reference.
Closed: Increases or decreases the frequency reference.
UP 2 and Down 2 commands must be set in combination with each other.
The frequency reference source must be assigned to the operator (b1-01
= "0").
Open: KEB Ride-Thru 2 enabled
Closed: Normal operation
Open: Normal operation
Closed: KEB Ride-Thru 2 enabled
Open: Normal operation
Closed: Short-Circuit Braking
Open: Short-Circuit Braking
Closed: Normal operation
Direction of rotation detection (for V/f with Simple PG Feedback)
Reserved for DWEZ input functions
Open: DWEZ enabled
Closed: DWEZ disabled
H2: Multi-Function Digital Outputs
Use H2 parameters to assign functions to the multi-function digital outputs.
Refer to H2 Multi-Function Digital Output
Settings on page
setting values.
Sets the output units for the watt hours when
Watt Hour Pulse Output is selected as the
digital output (H2-01, H2-02, or H2-03 = 39).
Outputs a 200 ms pulse signal when the watt-
hour counter increases by the units selected.
0: 0.1 kWh units
1: 1 kWh units
2: 10 kWh units
3: 100 kWh units
4: 1000 kWh units
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Description
Description
353 for a description of
Control
Mode
V/
f
O
O
O
O
O
O
O
O
O
O
-
-
O
O
O
Control
Mode
Range Def.
O
V/ P
L
f M
V
E A A A
0 to 192
0 A A A
<1>
2 A A A
0 to 4 0 A A A
Pg.
O
P
L
M
V
O O 184
O O 184
O O 184
O O 184
- - 184
O O 184
O O 184
O O 184
O O 185
O O 185
- O 185
- O 185
- - 186
O O 186
O O 186
Addr.
Pg.
Hex
40B 186
40C 186
40D 186
437 195