YASKAWA V1000 Technical Manual page 333

No. Name
Run Command Selection
b1-08
while in Programming Mode
b1-14 Phase Order Selection
Frequency Reference
b1-15
Selection 2
b1-16 Run Command Selection 2
Run Command at Power
b1-17
Up
DC Injection Braking Start
b2-01
Frequency
DC Injection Braking
b2-02
Current
DC Injection Braking Time/
b2-03 DC Excitation Time at
Start
DC Injection Braking Time
b2-04
at Stop
Magnetic Flux
b2-08
Compensation Value
Short Circuit Brake Time at
b2-12
Start
Short Circuit Brake Time at
b2-13
Stop
Speed Search Selection at
b3-01
Start
Speed Search Deactivation
b3-02
Current
Speed Search Deceleration
b3-03
Time
b3-05 Speed Search Delay Time
Output Current 1 during
b3-06
Speed Search
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Description
0: Run command accepted only in the operation menu.
1: Run command accepted in all menus.
2: Prohibit entering Programming Mode during Run
Sets the phase order for drive output terminals U/T1, V/T2
and W/T3.
0 : Standard
1 : Switch phase order
Selects the frequency reference input source 2.
0: Operator - Digital preset speed d1-01 to d1-17.
1: Terminals - Analog input terminal A1 or A2
2: MEMOBUS communications
3: Option PCB
4: Pulse Input (Terminal RP)
Selects the run command input source 2.
0: Operator - RUN and STOP keys on the digital operator.
1: Digital input terminals
2: MEMOBUS communications
3: Option PCB
Determines the operation when a Run command is active at
power up of the drive.
0: Run command not issued, needs to be cycled
1: Run command issued, motor operation start
b2: DC Injection Braking
Use b2 parameters to configure DC Injection Braking operation
Sets the frequency at which DC Injection Braking starts
when Ramp to Stop (b1-03 = 0) is selected. If b2-01< E1-09,
DC Injection Braking starts at E1-09.
Sets the DC Injection Braking current as a percentage of the
drive rated current.
Sets DC Injection Braking time at start. Disabled when set
to 0.00 seconds.
Sets DC Injection Braking time at stop.
When b1-03 = 2, actual DC Injection time is calculated as
follows:
(b2-04) x 10 x (Output Freq)/(E1-04). When b1-03 = 0, this
parameter sets the amount of DC Injection time applied to
the motor at the end of the decel ramp or High Slip Braking.
Disabled when set to 0.00.
Sets the magnetic flux compensation as a percentage of the
no-load current value (E2-03).
Sets the time for Short-Circuit brake operation at start.
Disabled when set to 0.00.
<2>
Sets the Short-Circuit brake operation time at stop. Used to
stop a motor rotating due to inertia. Disabled when set to 0.00
seconds.
<2>
b3: Speed Search
Use b3 parameters to configure Speed Search function operation.
Enables/disables the Speed Search function at start.
0: Disabled - Speed Search is not automatically performed
at start.
1: Enabled - Speed Search is automatically performed at
start.
Sets the current level at which the speed is assumed to be
detected and Speed Search is ended. Set as a percentage of
the drive rated current.
Sets the time constant used to reduce the output frequency
during Speed Search. Related to a change from max. output
frequency to 0.
Delays the Speed Search operation after a momentary power
loss to allow time for an external output contactor to close. 0.0 to 100 0.2 s A A A
Sets the current injected to the motor at the beginning of
Estimation type Speed Search. Set as a factor of the motor
rated current.
B.2 Parameter Table
Control
Mode
Addr.
Range Def.
O
V/ P
L
f M
V
0 to 2 0 A A A
0, 1 0 A A A
0 to 4 0 A A A
0 to 3 0 A A A
0, 1 0 A A A
0.0 to 0.5
A A A
10.0 Hz
0 to 75 50% A A A
0.00 s
0.00 to
A A A
<1>
10.00
0.00 to
0.50 s A A −
10.00
0 to 1000 0% − A −
0.00 to
0.00 s − − A
25.50
0.00 to
0.50 s − − A
25.50
0, 1 0 A A A
120
0 to 200 A A −
<3>
0.1 to
2.0 s A A −
10.0
<4>
0.0 to 2.0 A A −
Pg.
Hex
187 122
1C3 123
1C4 123
1C5 123
1C6 123
189 123
18A 124
18B 124
18C 124
190 124
1BA 124
1BB 125
191 128
192 128
193 128
B
195 128
196 128
333