YASKAWA V1000 Technical Manual page 377

No. Name
U6-07 q-axis ACR Output
U6-08 d-Axis ACR Output
Frequency Reference Bias
U6-20
(Up/Down 2)
U6-21 Offset Frequency
U6-80 to
Option Monitors 1 to 20
U6-99
U8-01 –
U8-02 –
U8-03 –
U8-04 –
U8-05 –
U8-06 –
U8-07 –
U8-08 –
U8-09 –
U8-10 –
<1> Display is in the following units: BA0001 to BA0018, 2A0001 to 2A0040, and 4A0001 to 4A0023: 0.01 A units.
2A0056 to 2A0069, 4A0031 to 4A0038: 0.1 A units.
<2> U1-03, U2-05, and U4-13 display monitor contents in amp units. When reading the value of these monitors via MEMOBUS/Modbus, a value
of 8192 is equal to 100% of the drive rated output current.
<3> Parameter setting value is not reset to the default value during drive initialization, A1-03 = 1110, 2220, 3330
<4> Available in drive software versions PRG: 1011 and later. Maximum value is 65536 in drive software versions PRG: 1010 and earlier.
<5> When this value reaches 100%, the maintenance period has been reached for the component in question and the drive is at risk of faulting out
due to component failure. Periodically check the maintenance monitors to avoid this situation.
<6> Available in drive software versions PRG: 1011 and later.
<7> MEMOBUS/Modbus communications data is in 10 h units. If data in 1 h units are also required, refer to register 0099H.
<8> MEMOBUS/Modbus communications data is in 10 h units. If data in 1 h units are also required, refer to register 009BH.
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Description
Displays the current control (ACR) output of for the motor
secondary current (Iq).
Displays the current control (ACR) output of for the motor
excitation current (Id).
Displays the bias value used to adjust the frequency
reference.
The total value of the offset frequencies d7-01, d7-02 and
d7-03 selected with digital inputs 44 to 46 is displayed.
Monitors reserved for use by the communication option
card. Monitor content varies based on the communication
option connected to the drive.
Refer to the instruction manual for the option card for more
information..
U8: Custom Monitors for DriveWorksEZ
U8 monitors are reserved for DriveWorksEZ
Reserved for DriveWorksEZ, Monitor 1.
Reserved for DriveWorksEZ, Monitor 2.
Reserved for DriveWorksEZ, Monitor 3.
Reserved for DriveWorksEZ, Monitor 4.
Reserved for DriveWorksEZ, Monitor 5.
Reserved for DriveWorksEZ, Monitor 6.
Reserved for DriveWorksEZ, Monitor 7.
Reserved for DriveWorksEZ, Monitor 8.
Reserved for DriveWorksEZ, Monitor 9.
Reserved for DriveWorksEZ, Monitor 10.
B.2 Parameter Table
Control
Mode
Analog Output
Unit
O
Level
V/
L
f
V
10 V: 100% 0.1% − A −
10 V: 100% 0.1% − A −
10 V: max.
0.1% A A A
frequency
10 V: max.
0.1% A A A
frequency
No signal output
– A A A
avail.
0.01
– Α A Α
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
0.01
– A A A
%
Addr.
Hex
P
M
5F
60
7D4
7D5
7B0 to
7F9
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
B
377