E4: Motor 2 Parameters - YASKAWA V1000 Technical Manual

5.5 E: Motor Parameters
No.
E3-04
E3-05
E3-06
E3-07
E3-08
E3-09
E3-10
E3-11
E3-12
E3-13
<1> Values shown here are for 200 V class drives. Multiply voltage values by 1.15 for U-spec drives. Double the value when using 400 V class
drives.
<2> Default setting is determined by the control mode for motor 2.
<3> The default value is for the following localized drives: Japan (Model code: CIMR-VAoA) and Asia (Model code: CIMR-VToA)
China Localized Drive Default Values on page 381
1. The following condition must be true when setting up the V/f pattern: E3-09 ≤ E3-07 ≤ E3-06 ≤ E3-11 ≤ E3-04
Note:
2. To make the V/f pattern a straight line set E3-09 = E3-07. In this case the E3-08 setting is disregarded.
u

E4: Motor 2 Parameters

E4 parameters contain the motor data for motor 2. These parameters are usually set automatically during the Auto-Tuning
process. They may need to be set manually if there is a problem performing Auto-Tuning.
n E4-01: Motor 2 Rated Current
Set E4-01 to the full load amps (FLA) stamped on the nameplate of motor 2. During Auto-Tuning the value must be entered
to parameter T1-04. If Auto-Tuning completes successfully, the value entered will automatically be saved to E4-01.
No.
E4-01
Note: Display is in the following units: BA0001 to BA0018, 2A0001 to 2A0040, and 4A0001 to 4A0023: 0.01 A units.
2A0056 to 2A0069, 4A0031 to 4A0038: 0.1 A units.
n E4-02: Motor 2 Rated Slip
This parameter sets the motor 2 rated slip frequency. The drive calculates this value automatically during Rotational Auto-
Tuning.
For information on calculating the motor rated slip, see the description for E2-02.
168
Parameter Name
Motor 2 Max Output Frequency
Motor 2 Max Voltage
Motor 2 Base Frequency
Motor 2 Mid Output Frequency
Motor 2 Mid Output Frequency Voltage
Motor 2 Minimum Output Frequency
Motor 2 Minimum Output Frequency Voltage
Motor 2 Mid Output Frequency 2
Motor 2 Mid Output Frequency Voltage 2
Motor 2 Base Voltage
for the default values of China localized (Model code: CIMR-VBoA) drives.
Output (V)
E3-05
E3-12
E3-13
E3-08
E3-10
E3-09
Figure 5.43 V/f Pattern for Motor 2
Parameter Name
Motor 2 Rated Current
E3-06 E3-11 E3-04
E3-07
Frequency (Hz)
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Setting Range
40.0 to 400.0 Hz
<1>
0.0 to 255.0 V
0.0 to 400.0 Hz
0.0 to 400.0 Hz
<1>
0.0 to 255.0 V
0.0 to 400.0 Hz
<1>
0.0 to 255.0 V
0.0 to 400.0 Hz
<1>
0.0 to 255.0 V
<1>
0.0 to 255.0 V
Setting Range
10 to 200% of the drive rated
current.
Default
<3>
60.0 Hz
<1>
200.0 V
<3>
60.0 Hz
<2> <3>
<2>
<2> <3>
<2>
0.0 Hz
0.0 Vac
0.0 Vac
.Refer to
Default
Depending on
o2-04