YASKAWA V1000 Technical Manual page 471

Motor Rated Power .......................................................... 371
Motor Rated Slip............................................................. 343
Motor Rated Voltage .................................................. 103, 371
Motor Rotates After the Drive Output is Shut Off ...................... 286
Motor Rotates Faster Than the Frequency Reference................... 283
Motor Rotates in One Direction Only............................... 282, 287
Motor Secondary Current (Iq) ............................................. 376
Motor Selection 1/2.......................................................... 371
Motor Speed .................................................................. 372
Motor Speed at Previous Fault ............................................. 373
Motor Speed Error ........................................................... 252
Motor Speed Fault ........................................................... 278
Motor Stalls During Acceleration or With Large Loads ............... 283
Motor Stator Resistance..................................................... 345
Motor Stops During Acceleration or When a Load is Connected..... 287
Motor Switch during Run................................................... 272
Motor Temperature (PTC input)........................................... 355
Motor Temperature Input Filter Time (PTC input) ..................... 358
Motor Wiring................................................................... 60
Multi-Function Analog 1 (Terminal AM Monitor Selection).......... 355
Multi-Function Analog 1 (Terminal AM Output Gain) ................ 356
Multi-Function Analog Input Selection Error...................... 251, 275
Multi-Function Digital Inputs ................................................ 63
Multi-Function Digital Input Terminal S1 Function Selection ........ 350
Multi-Function Digital Input Terminal S2 Function Selection ........ 350
Multi-Function Digital Input Terminal S3 Function Selection ........ 350
Multi-Function Digital Input Terminal S4 Function Selection ........ 350
Multi-Function Digital Input Terminal S5 Function Selection ........ 350
Multi-Function Digital Input Terminal S6 Function Selection ........ 350
Multi-Function Digital Input Terminal S7 Function Selection ........ 350
Multi-Function Digital Output ............................................... 63
Multi-Function Input Selection Error ..................................... 274
Multi-Function Input Setting Error........................................ 251
Multi-Function Photocoupler Output ....................................... 63
Multiple Drive Wiring ........................................................ 60
Multi-Step Speed Reference................................................ 350
Multi-Step Speed Reference 4 ............................................. 351
N
n1-01........................................................................... 365
n1-02......................................................... 246, 263, 285, 365
n1-03........................................................................... 365
n1-05........................................................................... 365
n1 Hunting Prevention ...................................................... 365
n2-01......................................................... 247, 284, 285, 365
n2-02......................................................... 247, 282, 284, 365
n2-03............................................................... 247, 282, 365
n2 Speed Feedback Detection Control Function ........................ 365
n3-01........................................................................... 365
n3-02........................................................................... 365
n3-03........................................................................... 365
n3-04..................................................................... 261, 365
n3-13..................................................................... 258, 365
n3-21........................................................................... 365
n3-23........................................................................... 365
n3 High Slip Braking........................................................ 365
n6-01........................................................................... 366
n6 Online Tuning of Resistance between Motor Lines ................. 365
n8-45............................................................... 263, 287, 366
n8-47............................................................... 263, 287, 366
n8-48........................................................................... 366
n8-49........................................................................... 366
n8-51..................................................................... 264, 366
n8-54........................................................................... 366
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
n8-55........................................................................... 366
n8-62........................................................................... 366
n8-63........................................................................... 366
n8-65........................................................................... 366
n8-68........................................................................... 366
n8-87........................................................................... 366
n8-88........................................................................... 366
n8-89........................................................................... 366
n8-90........................................................................... 366
n8-91........................................................................... 366
n8 Permanent Magnet (PM) Motor Control.............................. 366
n Advanced Performance Set Up .......................................... 365
NEMA Type 1............................................................. 41, 43
Node Setup ................................................................... 351
Node Setup Error ...................................................... 250, 258
Noise From the Drive or Output Lines When the Drive is Powered On ... 285
No-Load Current Error................................................ 252, 278
No-Load Operation .......................................................... 106
Normal Duty Ratings........................................................ 150
Notes on Motor Operation.................................................... 21
nSE ...................................................................... 250, 258
Number of Auto Restart Attempts......................................... 360
Number of Motor Poles ............................................... 343, 371
Number of Run Commands ................................................ 374
Number of Speed Search Restarts ......................................... 334
O
o1-01........................................................................... 367
o1-02........................................................................... 367
o1-03........................................................................... 367
o1-10........................................................................... 367
o1-11........................................................................... 367
o1 Display Settings .......................................................... 367
o2-01..................................................................... 280, 367
o2-02..................................................................... 281, 367
o2-03..................................................................... 108, 368
o2-04......................................................... 246, 259, 274, 368
o2-05........................................................................... 368
o2-06..................................................................... 262, 368
o2-07........................................................................... 368
o2-09........................................................................... 368
o2 Multi-Function Selections .............................................. 367
o3-01........................................................................... 368
o3-02........................................................................... 368
o4-01........................................................................... 368
o4-02........................................................................... 368
o4-03............................................................... 259, 270, 368
o4-05........................................................................... 368
o4-07........................................................................... 368
o4-09........................................................................... 368
o4-11........................................................................... 368
o4-12........................................................................... 369
o4-13........................................................................... 369
o4 Maintenance Period...................................................... 368
oC ........................................................................ 250, 258
oFA00 ................................................................... 250, 259
oFA01 ................................................................... 250, 259
oFA03 ................................................................... 250, 259
oFA04 ................................................................... 250, 259
oFA30 to oFA43 ....................................................... 250, 259
Offset Frequency............................................................. 377
Offset Frequency 1 .......................................................... 341
Offset Frequency 1 Addition ............................................... 351
Offset Frequency 2 .......................................................... 341
Index
471