YASKAWA V1000 Technical Manual page 472

Index
Offset Frequency 2 Addition ............................................... 351
Offset Frequency 3 .......................................................... 341
Offset Frequency 3 Addition ............................................... 351
oH ............................................................ 250, 251, 259, 270
oH1 ...................................................................... 250, 259
oH2 ...................................................................... 251, 271
oH3 .......................................................... 250, 251, 259, 271
oH4 ...................................................................... 250, 260
oH Pre alarm.................................................................. 353
oH Pre-alarm Time Limit................................................... 354
oL1....................................................................... 250, 260
oL2................................................................. 250, 261, 286
oL2 Characteristics Selection at Low Speeds............................ 363
oL3........................................................... 250, 251, 261, 271
oL4........................................................... 250, 251, 261, 271
oL5........................................................... 250, 251, 261, 271
oL7....................................................................... 250, 261
o Operator Related Parameters............................................. 367
oPE ............................................................................ 274
oPE01 ................................................................... 251, 274
oPE02 ................................................................... 251, 274
oPE03 ................................................................... 251, 274
oPE04 ................................................................... 251, 275
oPE05 ................................................................... 251, 275
oPE07 ................................................................... 251, 275
oPE08 ................................................................... 251, 275
oPE09 ................................................................... 251, 276
oPE10 ................................................................... 251, 276
oPE11 ................................................................... 251, 276
oPE13 ................................................................... 251, 276
oPE fault constant............................................................ 274
oPE Fault Parameter......................................................... 373
Open-Chassis ................................................................... 41
Open-Chassis IP20 ....................................................... 40, 41
Open Loop Vector ........................................................... 278
Open Loop Vector Control ....... 248, 253, 281, 282, 283, 284, 285, 286
Open Loop Vector Control Mode Tuning ................................ 247
Open Loop Vector Control Mode Tuning Parameters .................. 247
Operating with the Load Connected....................................... 107
Operation Errors ....................................................... 249, 251
Operation Selection at Deviation (for Simple PG V/f Control) ....... 347
Operation Selection at Overspeed (OS) (for Simple PG V/f).......... 347
Operation Selection at PG Open Circuit (PGo).......................... 347
Operation Selection when Digital Operator is Disconnected .......... 368
Operator Connection Fault ................................................. 250
Operator Message ID........................................................ 373
Operator Programming Errors ............................................. 274
oPr ....................................................................... 250, 262
Option/Drive Selection...................................................... 350
Option Card Communications Error ...................................... 250
Option Card External Fault........................................... 256, 268
Option Card Fault (Port A) ................................................. 250
Option Card Fault (port A) ................................................. 259
Option Card Reference...................................................... 376
Option Communication Error .................................. 249, 253, 266
Option Frequency Reference ............................................... 375
Option Monitors 1 to 20 .................................................... 377
Option Unit Fault ............................................................ 250
oS ............................................................ 250, 251, 262, 271
Oscillation or Hunting....................................................... 285
Output Current ............................................................... 372
Output Current (A) ........................................ 319, 320, 321, 322
Output Current (kVA)....................................................... 322
Output Current at Previous Fault .......................................... 373
472
Output current imbalance ................................................... 257
Output Frequency............................................................ 371
Output Frequency after Soft Start ......................................... 373
Output Frequency at Previous Fault....................................... 373
Output Frequency is not as High as Frequency Reference ............. 286
Output Ground Fault Detection Selection ................................ 363
Output of speed control (ASR) (for Simple V/f PG).................... 376
Output Phase Loss ..................................................... 250, 257
Output Phase Loss Protection Selection .................................. 363
Output Power................................................................. 372
Output Power at Previous Fault............................................ 373
Output Terminal Status ..................................................... 372
Output Terminal Status at Previous Fault ................................ 373
Output Voltage at Previous Fault .......................................... 373
Output Voltage Bias ......................................................... 355
Output Voltage Limit........................................................ 366
Output Voltage Limit Gain 1............................................... 366
Output Voltage Limit Gain 2............................................... 366
Output Voltage Limit Operation Selection ............................... 338
Output Voltage Limit Selection............................................ 366
Output Voltage Limit Switching Current Hysteresis Width ........... 366
Output Voltage Limit Switching Current Level ......................... 366
Output Voltage Limit Switching Speed................................... 366
Output Voltage Reference .................................................. 372
Output Voltage Reference (Vd)............................................ 376
Output voltage reference (Vq) ............................................. 376
ov............................................................. 250, 251, 262, 272
Overcurrent ............................................................. 250, 258
Overexcitation Deceleration Gain ................................... 258, 365
Overexcitation Operation Selection ....................................... 365
Overheat 1 (Heatsink Overheat) ........................................... 259
Overheat Alarm Level....................................................... 362
Overheat Pre-Alarm Operation Selection ................................ 363
Overload oL1 (oL1 Alarm)................................................. 353
Overload Tolerance........................................ 319, 320, 321, 322
Overspeed (for Simple V/f with PG).......................... 250, 251, 271
Overspeed (Simple V/f with PG) .......................................... 262
Overtorque/Undertorque Detection Level ................................ 355
Overtorque 1............................................................ 251, 271
Overtorque 2............................................................ 251, 271
Overtorque Detection 1 ............................................... 250, 261
Overtorque Detection 2 ............................................... 250, 261
Overvoltage....................................................... 250, 251, 262
Overvoltage Occurs When Running at a Constant Speed .............. 282
Overvoltage Suppression ................................................... 262
ov Occurs When Starting a Fan or Motor Speed Loss Occurs......... 286
ov Suppression Function Selection........................................ 359
P
Parameter Range Setting Error............................................. 274
Parameter Selection Error ............................................ 251, 275
Parameter Setting Range Error............................................. 251
Parameter Settings ............................................................. 85
PASS .................................................................... 251, 272
Password ...................................................................... 331
Password Setting............................................................. 331
Password Settings............................................................ 108
Peak Hold Current ........................................................... 375
Peak Hold Output Frequency .............................................. 375
Performance Life .............................................................. 18
Peripheral Devices Affected by Drive Operation ....................... 288
Permanent Magnet Motor Control........................................... 17
PF ........................................................................ 250, 263
PG Disconnect (for Simple V/f with PG)............... 250, 251, 263, 272
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual