YASKAWA V1000 Technical Manual page 474

Index
Sinking/Sourcing Mode Switch.............................................. 34
Slip Compensation Gain .............................................. 247, 337
Slip Compensation Limit ................................................... 338
Slip Compensation Primary Delay Time ................................. 338
Slip Compensation Primary Delay Time Constant...................... 247
Slip Compensation Selection during Regeneration ..................... 338
Soft Charge Bypass Relay Maintenance Time..................... 251, 270
Soft Charge Circuit Fault ................................................... 250
Soft Current Limit Selection ............................................... 363
Soft Starter Speed Reference at Previous Fault.......................... 373
Software No. (Flash) ........................................................ 373
Software No. (ROM) ........................................................ 373
Speed Agreement Detection Level ........................................ 360
Speed Agreement Detection Level (+/-) .................................. 360
Speed Agreement Detection Width ....................................... 360
Speed Agreement Detection Width (+/-) ................................. 360
Speed Control Integral Time 1 ....................................... 262, 272
Speed Control Proportional Gain 1.................................. 262, 272
Speed Deviation (for Simple V/f with PG)......................... 255, 267
Speed Estimation Type Speed Search..................................... 262
Speed Feedback Detection Control (AFR) Gain ........................ 365
Speed Feedback Detection Control (AFR) Time Constant............. 365
Speed Feedback Detection Control (AFR) Time Constant 2 .......... 365
Speed Feedback Detection Control [AFR] Time Constant 1 .......... 285
Speed Feedback Detection Control Gain ................................. 366
Speed Feedback Detection Control Gain during ov Suppression ..... 366
Speed Feedback Detection Suppression Gain............................ 287
Speed Search ................................................................. 354
Speed Search Deactivation Current ....................................... 333
Speed Search Deceleration Time .......................................... 333
Speed Search Delay Time .................................................. 333
Speed Search Estimation Type............................................. 261
Speed Search Induced Voltage Level ..................................... 334
Speed Search Method Selection ........................................... 334
Speed Search Restart Current Level....................................... 334
Speed Search Restart Detection Time..................................... 334
Speed Search Retry Interval Time......................................... 334
Speed Search Selection at Start ............................................ 333
Stall Prevention ........................................................ 248, 262
Stall Prevention During Deceleration ................................. 72, 260
Stall Prevention Level during Acceleration .............................. 359
Stall Prevention Level during Run ........................................ 359
Stall Prevention Limit during Acceleration .............................. 359
Stall Prevention Selection during Acceleration.......................... 359
Stall Prevention Selection during Deceleration.......................... 359
Stall Prevention Selection during Run .................................... 359
Standard Connection Diagram .......................................... 48, 49
Stationary Auto-Tuning..................................................... 101
STo ...................................................................... 250, 264
STo Deviation Detection ................................................... 364
STo Fault Detection Level.................................................. 364
STOP button Input..................................................... 252, 277
STOP Key Function Selection ............................................. 367
Stopping Method After Communication Error .......................... 356
Stopping Method Selection................................................. 332
Suppression Diode Connection .............................................. 64
T
T1-00 .......................................................................... 371
T1-01 .................................................................... 100, 371
T1-02 .............................................................. 103, 277, 371
T1-03 .............................................................. 103, 277, 371
T1-04 .............................................................. 103, 277, 371
T1-05 .............................................................. 103, 277, 371
474
T1-06 .................................................................... 103, 371
T1-07 .............................................................. 103, 277, 371
T1-11 .......................................................................... 371
Terminal A1/A2 Enable..................................................... 350
Terminal A1 Bias Setting................................................... 354
Terminal A1 Gain Setting .................................................. 354
Terminal A1 Signal Level Selection ...................................... 354
Terminal A2 Bias Setting................................................... 354
Terminal A2 Function Selection........................................... 354
Terminal A2 Gain Setting .................................................. 354
Terminal A2 Signal Level Selection ...................................... 354
Terminal Block Configuration ............................................... 52
Terminal Board .............................................................. 299
Terminal Board Communications Error .................................. 254
Terminal Board Not Connected............................................ 255
Terminal Board Wiring Guide ............................................... 66
Terminal MA, MB and MC Function Selection (relay) ................ 352
Terminal P1 Function Selection (open-collector) ....................... 352
Terminal P2 Function Selection (open-collector) ....................... 352
Test Run............................................... 100, 101, 102, 103, 106
Tightening Torque ............................................................. 56
Timer Function Input........................................................ 351
Timer Function Off-Delay Time........................................... 334
Timer Function On-Delay Time ........................................... 334
Timer Output ................................................................. 353
Timing Fault............................................................ 250, 255
T Motor Tuning .............................................................. 370
Too Many Speed Search Restarts.................................... 250, 264
Torque Compensation at Forward Start................................... 338
Torque Compensation at Reverse Start ................................... 338
Torque Compensation Gain .......................................... 246, 338
Torque Compensation Gain - Motor 2 .................................... 345
Torque Compensation Primary Delay Time ........... 246, 285, 287, 338
Torque Compensation Primary Delay Time Constant 1................ 247
Torque Compensation Primary Delay Time Constant 2................ 247
Torque Compensation Time Constant .................................... 338
Torque Detection 1 (N.O.).................................................. 353
Torque Detection 2 (N.C.).................................................. 353
Torque Detection 2 (N.O.).................................................. 353
Torque Detection Level 1................................................... 361
Torque Detection Level 2................................................... 361
Torque Detection Selection 1 .............................................. 361
Torque Detection Selection 2 .............................................. 361
Torque Detection Time 1 ................................................... 361
Torque Detection Time 2 ................................................... 361
Torque Limit Control Method Selection during Accel/Decel ......... 362
Torque Limit Integral Time Constant ..................................... 362
Torque Limits ................................................................ 248
Torque Reference ............................................................ 372
Torque Reference at Previous Fault ....................................... 373
Torque Specifications, Single Phase 200 V Class................... 56, 441
Torque Specifications, Three Phase 200 V Class ................... 57, 442
Torque Specifications, Three Phase 400 V Class ................... 59, 444
Transistor Input Signal ................................................... 67, 68
TrPC ..................................................................... 251, 273
Tuning Errors................................................................. 249
U
U1-01 .............................................................. 281, 283, 371
U1-02 .......................................................................... 371
U1-03 .......................................................................... 372
U1-04 .......................................................................... 372
U1-05 .......................................................................... 372
U1-06 .......................................................................... 372
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual