YASKAWA V1000 Technical Manual page 343

No. Name
E2-01 Motor Rated
<8> Current
E2-02 Motor Rated Slip
Motor No-Load
E2-03
Current
Number of Motor
E2-04
Poles
Motor Line-to-Line
E2-05
Resistance
Motor Leakage
E2-06
Inductance
Motor Iron-Core
E2-07 Saturation
Coefficient 1
Motor Iron-Core
E2-08 Saturation
Coefficient 2
Motor Mechanical
E2-09
Loss
Motor Iron Loss for
E2-10 Torque
Compensation
Motor Rated
E2-11
Output
Motor Iron-Core
E2-12 Saturation
Coefficient 3
Motor 2 Control
E3-01
Method
YASKAWA ELECTRIC SIEP C710606 16C YASKAWA AC Drive – V1000 Technical Manual
Description
Sets the motor nameplate full load current in amperes (A).
Automatically set during Auto-Tuning.
Note: Set E2-03 (Motor No-Load Current) before making
changes to E2-01. An oPE01 error will be triggered if
E2-01 < E2-03.
Sets the motor rated slip in Hertz.
Automatically set during rotational Auto-Tuning.
Sets the magnetizing current of the motor in Ampere.
Automatically set during rotational Auto-Tuning.
Note: Set E2-03 (Motor No-Load Current) before making
changes to E2-01. An oPE01 error will be triggered if
E2-01 < E2-03.
Sets the number of motor poles. Automatically set during
Auto-Tuning.
Sets the phase-to-phase motor resistance in ohms.
Automatically set during Auto-Tuning.
Sets the voltage drop due to motor leakage inductance as a
percentage of motor rated voltage.
Automatically set during Auto-Tuning.
Sets the motor iron saturation coefficient at 50% of
magnetic flux. Automatically set during Auto-Tuning.
Sets the motor iron saturation coefficient at 75% of
magnetic flux. Automatically set during Auto-Tuning.
Sets the motor mechanical loss as a percentage of motor
rated power (kW). Adjust in the following circumstances:
When there is a large amount of torque loss due to motor
bearing friction.
When there is a large amount of torque loss.
Sets the motor iron loss in watts (W).
Sets the motor rated power in kilowatts (kW).
Automatically set during Auto-Tuning. (1 HP = 0.746 kW).
Set to the motor iron saturation coefficient at 130% of
magnetic flux.
Automatically set during rotational Auto-Tuning.
E3: Motor 2 V/f Characteristics
Use E3 parameters to set the V/f pattern for a second motor.
0: V/f Control
2: Open Loop Vector (OLV)
B.2 Parameter Table
Control
Mode
Range Def.
V/f O
LV
10 to 200%
of drive
rated
<10>
S S
current
<9>
0.00 to
<10>
A A
20.00
0 to less
<10> A A
than E2-01
2 to 48 4 poles A A
0.000 to
65.000 <10>
A A
<11>
0.0 to 40.0 <10> A A
0.00 to
0.50 − A
0.50
E2-07 to
0.75 − A
0.75
0.0 to 10.0 0.0% − A
<10>
0 to 65535 A −
0.40 kW
0.00 to
S S
<6>
650.00
1.30 to
1.30 − A
5.00
0 or 2 0 A A
Addr. Hex Pg.
PM
− 30E 165
− 30F 166
− 310 166
− 311 166
− 312 166
− 313 166
− 314 166
− 315 167
− 316 167
− 317 167
− 318 167
− 328 167
− 319 167
B
343