Control Mode Dependent Parameter Default Values; A1-02 (Motor 1 Control Mode) Dependent Parameters - YASKAWA A1000 Series Technical Manual

B.4 Control Mode Dependent Parameter Default Values
B.4 Control Mode Dependent Parameter Default Values
The tables below list parameters that depend on the control mode selection (A1-02 for motor 1, E3-01 for motor 2).
These parameters are initialized to the shown values if the control mode is changed.

◆ A1-02 (Motor 1 Control Mode) Dependent Parameters

Table B.2 A1-02 (Motor 1 Control Mode) Dependent Parameters and Default Values
No. Name
b2-01 DC Injection Braking Start Frequency
b2-04 DC Injection Braking Time at Stop
b3-01 Speed Search Selection at Start
b3-02 Speed Search Deactivation Current
b3-14 Bi-Directional Speed Search Selection
b8-01 Energy Saving Control Selection
b8-02 Energy Saving Gain
b8-03 Energy Saving Control Filter Time Constant
C2-01 S-Curve Time at Acceleration Start
C3-01 Slip Compensation Gain
C3-02 Slip Compensation Primary Delay Time
C4-01 Torque Compensation Gain
C4-02 Torque Compensation Primary Delay Time
C5-01 ASR Proportional Gain 1
C5-02 ASR Integral Time 1
C5-03 ASR Proportional Gain 2
C5-04 ASR Integral Time 2
C5-06 ASR Primary Delay Time Constant
C6-02 Carrier Frequency Selection
E1-04 to
The default setting of these parameters depends on the control mode but also on the drive capacity. Refer to
E1-10
F1-05 PG 1 Rotation Selection
F1-09 Overspeed Detection Delay Time
L1-01 Motor Overload Protection Selection
L3-20 DC Bus Voltage Adjustment Gain
L3-21 Accel/Decel Rate Calculation Gain
L4-02 Speed Agreement Detection Width
L4-04 Speed Agreement Detection Width (+/–)
L8-38 Carrier Frequency Reduction Selection
L8-40 Carrier Frequency Reduction Off Delay Time
o1-03 Digital Operator Display Selection
o1-04 V/f Pattern Display Unit
<9> Default setting is determined by the drive model (o2-04) and duty selection (C6-01).
454
Setting Range Resolution
0.0 to 10.0 0.1
0.00 to 10.00 0.01 s
0 to 1 –
0 to 200 1%
0 to 1 1
0 to 1 –
0.0 to 10.0 0.1
0.00 to 10.00 0.01 s
0.00 to 10.00 0.01 s
0.0 to 2.5 0.1
0 to 10000 1 ms
0.00 to 2.50 0.01
0 to 10000 1 ms
0.00 to 300.00 0.01
0.000 to 10.000 0.001 s
0.00 to 300.00 0.01
0.000 to 10.000 0.001 s
0.000 to 0.500 0.001 s
1 to F –
0 to 1 –
0.0 to 2.0 0.1 s
0 to 4 –
0.00 to 5.00 0.01
0.00 to 10.00 0.01
0.0 to 20.0 0.1
0.0 to 20.0 0.1
0 to 2 1
0.00 to 2.00 0.01 s
0 to 3 1
0 to 1 1
YASKAWA ELECTRIC SIEP C710616 27C YASKAWA AC Drive A1000 Technical Manual
Control Modes (A1-02)
V/f (0) V/f w/PG (1) OLV (2)
0.5 Hz 0.5 Hz 0.5 Hz
0.50 0.50 0.50
0 1 0
120 – 100
1 0 1
0 0 0
– – 0.7
0.50,
2.00
(Motor
– –
Capacity:
55 kW and
above)
0.20 0.20 0.20
0.0 – 1.0
2000 – 200
1.00 1.00 1.00
200 200 20
– 0.20 –
– 0.200 –
– 0.02 –
– 0.050 –
– – –
7 7 7
<9> <9> <9>
V/f Pattern Default Values on page
0 0 0
– 1.0 –
1 1 1
1.00 1.00 0.30
1.00 1.00 1.00
2.0 Hz 2.0 Hz 2.0 Hz
2.0 Hz 2.0 Hz 2.0 Hz
<9> <9> <9>
0.50 0.50 0.50
0 0 0
– – –
CLV (3)
0.5 Hz
0.50
1
–
1
0
1.0
0.01,
0.05
(Motor
Capacity:
55 kW and
above)
0.20
1.0
–
–
–
20.00
0.500
20.00
0.500
0.004
7
<9>
456.
0
0.0
1
0.30
1.00
2.0 Hz
2.0 Hz
<9>
0.50
0
0