Infranet Controller And Nsm Installation Overview; Chapter 2 Infranet Controller And Nsm Installation Overview; Uac Installation Overview - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 Manual
Configuring infranet controllers guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01:
- Manual (444 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
CHAPTER 2
Infranet Controller and NSM Installation
Overview
UAC Installation Overview
Related
Documentation
Copyright © 2010, Juniper Networks, Inc.
UAC Installation Overview on page 7
NSM Installation Overview on page 8
NOTE: For important safety information, read Juniper Networks Security
Products Safety Guide.
The UAC components to be installed are the following:
Install Infranet Enforcer and/or 802.1X hardware and perform the basic setup. See
1.
the documentation that shipped with the system or visit the Juniper Networks Web
site at
http://www.juniper.net/techpubs/
Install Infranet Controller hardware and perform the basic setup using the serial
2.
console. See the Juniper Networks Unified Access Control Installation Guide.
License the Infranet Controller and verify user accessibility. Follow the initial
3.
configuration Task Guide instructions embedded in the Infranet Controller Web console.
Configure an SSL connection between the Infranet Controller appliance and your
4.
Infranet Enforcer appliances and/or 802.1X switches. See the Juniper Networks Unified
Access Control Quick Start Guide or Part 1, "Getting Started," of the Juniper Networks
Unified Access Control Administration Guide.
NSM Installation Overview on page 8
NSM and Device Management Overview on page 3
Communication Between an Infranet Controller and NSM Overview on page 3
to download the appropriate documentation.
7
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 and is the answer not in the manual?