Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 Manual page 107
Configuring infranet controllers guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01:
- Manual (444 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
Related
Documentation
Copyright © 2010, Juniper Networks, Inc.
Table 25: Authentication Realms Configuration Details (continued)
Option
Function
Enable Dynamic
Enables an automatic timer
policy evaluation
for dynamic policy
evaluation of this realm's
authentication policy, role
mapping rules, and role
restrictions.
Refresh roles
Refreshes the roles of all
users in this realm. (This
option does not control the
scope of the Refresh Now
button.)
Refresh policies
Refreshes the resource
policies (not including
Meeting and Email Client)
for all users in this realm.
(This option does not
control the scope of the
Refresh Now button.)
Refresh interval
Specifies how often you
(minutes)
want the Infranet Controller
to perform an automatic
policy evaluation of all
currently signed-in realm
users. Specify the number
of minutes (5 to 1440).
Configuring Role Mapping Rules (NSM Procedure) on page 90
Configuring Infranet Controller Source IP Access Restrictions (NSM Procedure) on
page 61
Chapter 9: Configuring Authentication Realms
Your Action
Select this option to enable dynamic policy
evaluation.
NOTE: If you select Dynamic policy
evaluation and you do not select Refresh
roles and Refresh resource policies, the
Infranet Controller evaluates the realm's
authentication policy, role mapping rules,
and role restrictions only.
Because dynamic policy evaluation can
potentially impact system performance,
keep these guidelines in mind:
Automatic (timer-based) refreshing of
user roles and resource policies can affect
system performance. You can improve
performance by disabling either or both
of the Refresh roles and Refresh resource
policies options to reduce the scope of
the refresh.
You can improve performance, by setting
the Refresh interval option to a longer
time period.
Use the Refresh Now button at times
when users may not be affected.
Select this option to refresh roles.
Select this option refresh policies.
Enter the frequency in minutes.
89
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 and is the answer not in the manual?