Configuring Infranet Enforcer Policies; Configuring Infranet Enforcer Resource Access Policies (Nsm Procedure) - Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 Manual
Configuring infranet controllers guide
Hide thumbs
Also See for NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01:
- Manual (444 pages) ,
- Administration manual (1026 pages) ,
- Installation manual (244 pages)
Table of Contents
Advertisement
CHAPTER 10
Configuring Infranet Enforcer Policies
Configuring Infranet Enforcer Resource Access Policies (NSM Procedure)
Copyright © 2010, Juniper Networks, Inc.
Configuring Infranet Enforcer Resource Access Policies (NSM Procedure) on page 93
Configuring Infranet Controller IPsec Routing Policies (NSM Procedure) on page 95
Configuring Infranet Controller IP Address Pool Policies (NSM Procedure) on page 98
Configuring Infranet Controller Source Interface Policies (NSM Procedure) on page 99
Configuring an Infranet Controller to Connect to a ScreenOS Enforcer (NSM
Procedure) on page 101
Configuring an Infranet Controller to Connect to a JUNOS Enforcer (NSM
Procedure) on page 102
An Infranet Enforcer resource access policy specifies which users are allowed or denied
access to a set of protected resources.
To configure Infranet Enforcer resource access policies:
In the NSM navigation tree, select Device Manager> Devices.
1.
Click the Device Tree tab, and then double-click the Infranet Controller for which you
2.
want to configure Infranet Enforcer resource access policies.
Click the Configuration tab. In the configuration tree, select UAC > Infranet Enforcer
3.
> Resource tab.
Add or modify settings for resource access policies as specified in Table 27 on page 93.
4.
Click one:
5.
OK—Saves the changes.
Cancel—Cancels the modifications.
Table 27: Resource Access Policies Configuration Details
Option
Name
Function
Your Action
Specifies the resource
Enter a name for the resource access
access policy name.
policy.
93
Advertisement
Table of Contents
Related Manuals for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
Related Products for Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - API GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - NSMXPRESS SERIES II REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper NETWORK AND SECURITY MANAGER 2010.3
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper MEDIA FLOW CONTROLLER 2.0.5
Need help?
Do you have a question about the NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING INFRANET CONTROLLER GUIDE REV 01 and is the answer not in the manual?