Toyota 02-8FGF15 Operator's Manual page 62

Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 3
01_A5028-0EA04_En.fm 61 ページ 2012年12月6日 木曜日 午後12時42分
INSPECTION PERIOD (Accomplish based on operating hours or
month, whichever is soonest.)
HYDRAULIC SYSTEM
Cylinder
1.
Cylinder mounting looseness and damage...............................................
2.
Rod and rod screw and rod end deformation and damage.......................
3.
Cylinder operation ...................................................................................
4.
Natural drop and natural forward tilt .......................................................
5.
Oil leakage and damage ...........................................................................
6.
Pin and cylinder shaft support wear and damage.....................................
7.
Lifting speed ............................................................................................
8.
Uneven movement ...................................................................................
Oil pump
9.
Oil leakage and unusual noise..................................................................
Hydraulic oil tank
10. Oil level and contamination .....................................................................
11. Tank and oil strainer.................................................................................
12. Oil leakage ...............................................................................................
Control lever
13. Linkage looseness ....................................................................................
14. Operation..................................................................................................
Oil control valve
15. Oil leakage ...............................................................................................
16. Relief pressure measurement ...................................................................
17. Relief valve and tilt lock valve function ..................................................
Oil pressure piping
18. Oil leakage ...............................................................................................
19. Deformation and damage.........................................................................
20. Linkage looseness ....................................................................................
ELECTRICAL SYSTEM
Ignition system
1.
Distributor cap cracking...........................................................................
2.
Spark plug burning and gap .....................................................................
3.
Distributor side terminal burning.............................................................
4.
Distributor cap center piece wear and damage ........................................
5.
Plug cord internal disconnection..............................................................
6.
Ignition timing .........................................................................................
Starter
7.
Pinion gear meshing.................................................................................
Charger
8.
Charging effect.........................................................................................
6
EVERY
3
6
12
MONTHS
WEEKS
EVERY
250
500
1000
2000
HOURS
T
I
I
M
I
I
M
I
I
I
C
I
I
I
I
M
I
I
I
T
I*
I
I*
I
I*
I
I*
I
I
M
I
I*
I
INSPECTION PERIOD (Accomplish based on operating hours or
month, whichever is soonest.)
Battery
9.
Battery electrolyte level ...........................................................................
10. Specific gravity ........................................................................................
Electrical wiring
11. Wiring harness damage ............................................................................
12. Fuses ........................................................................................................
Preheater
13. Glow plug heat coil breakage ..................................................................
14. Open circuit in intake heater ....................................................................
DPF muffler (Option)
15. Filter.........................................................................................................
16. Inline filter (for back pressure sensor) .....................................................
17
DPF valve.................................................................................................
SAFETY DEVICES, ETC.
Head guard
1.
Welded portion cracking ..........................................................................
2.
Deformation and damage.........................................................................
Back rest
3.
Mounting looseness .................................................................................
4.
Deformation, cracking and damage .........................................................
Lighting system
5.
Operation and mounting condition ..........................................................
Horn
6.
Operation and mounting condition ..........................................................
Instrument
7.
Operation..................................................................................................
Back-up buzzer (Option)
8.
Operation and mounting condition ..........................................................
SAS
9.
Operation..................................................................................................
10. Looseness at and/or damage to sensor fittings.........................................
11. Damage to, deformation of and/or oil leakage
at functional parts and loosening mounting .............................................
12. Looseness at and/or damage to wire harness ...........................................
13. Performance of lock cylinder and/or accumulator...................................
6
EVERY
3
6
12
MONTHS
WEEKS
EVERY
250
500
1000
2000
HOURS
I
M
I
I
I
I
Ι
I
C
I
I
T
I
I
I
I
I
I
I
I
I
I
en-61
en

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents